Haier HWM65-728 Bedienungsanleitung
User's manual
This manual is for
HWM65-728
Please read this manual
carefully before using.
Retain it for future reference.
Fully automatic washing machine
W
0030808138
Packing list Specification
Specifications
Installation and adjustment
Usage of the drain hose
Preparation before washing
Put in the laundries
Usage of the detergent
Close the top lid
Installation the water inlet hose
Disposal after washing
Finish washing
Use the operation buttons
Trouble-shooting
Answer to question
Contents
Names of the parts
Safety precautions
Meaning and description of the symbols
1
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Warning sign
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Control panel seat
Top lid component
Notes: All illustrations in this Manual are given for reference only. Your products
and accessories may show differences from these illustrations due to our
continuous improvement.
Names of the parts
Meaning and description of the symbols
Ú
Back cover
Power line
Drain hose
Cabinet handle
Water inlet valve
Jacket of
drain hose
Water absorption
cushion
Drain entrance
cover
Hanging
hole
Filter cover(2 pieces)
Control panel film
Cabinet
Adjustable foot
Adjustable foot film
Screw cover(right)
Back control board
Screw cover(left)
Outer tub cover
Lint filter(2 pieces)
Balance ring
Inner tub
Liquid whitener inlet
Fixed foot (3 pieces)
Detergent box
Pulsator
2
Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is in-
stalled on ground with carpet, do not
block the ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
The ventilation holes
at the bottom
3
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Petrol
Thinner
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
Please don t use the washer in the environment below 0 C; if the washer has been stored
below 0 C, please be sure to ensure the washer is placed under the room temperature for 24 hours
and then use otherwise the washing effects may be lowered or the washer may be damaged.
To change the direction of drain pipe, please contact the customer care agent of our company.
4
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Carpet
Back
Front
Bottom plate
Screw
Install the bottom plate
After opening the package, please lean the washing machine gently down
on soft items (like towel cloth,blanket, etc.). Install the bottom plate to the
bottom of the machine with seven screws by a cross screwdriver, then lift the
machine up gently. See to the figure:
Adjust the Installation position
The washing machine away from wall should be overrun 20mm. The largest
allowable slope of the shank base of the machine is 2 .The slanting or rough
ground will result in unstable running or stoppage of the machine.
Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the side of the
leg slightly, loosen the adjustable nut, and twist the leg.
2 . After adjustment, fasten the nut.
Fasten
Loosen
High Low
the adjustable nut
the adjustable feet
5
1.The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and
cost such long time that the machine may stop
at mid way.
2.Do not trample or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not less
than 30mm, and the length shall not
exceed 1.5m.
If the extra hose is too long, cut it either
at A or at B point.
Usage of the drain hose
The drain hose shall drain smoothly
Remarks: in order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman .
1.Dismantle the back cover of the washing
machine.
3.Dismantle the protecting cover of the drain
outlet at the other side Install the bushing as
per indicated in Figure 2.
Drain outlet
protecting cover
Drain hose
bushing
Figure 1
Figure 3
2.Take off the drain hose frame. Put down
the drain hose , put the drain hose into the
cabinet. take off the drain hose bushing
(As indicated in Figure 1).
Drain hose
frame Drain hose
bushing
Figure 2
Drain hose
frame
Drain outlet
protecting cover
Drain hose
Figure 4
How to change the direction of the drain hose
5.Install the protecting cover of the drain
outlet at the other side as per indicated in
Figure 4.
4.Extend the drain hose from the other side.
Fix the drain hose onto the base frame with
the drain hose frame.
(As indicated in Figure 3)
6
The exit end face of the faucet
Confirm the water faucet
Connection between the water inlet hose jointer and the water faucet
water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3.Fasten the four screws evenly. See to Figure 4.
remark: Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
water inlet hose jointer
Screw knife
water inlet hose
Figure 1
Figure 4 Figure 5
Slider
Lock lever
Installation the water inlet hose
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
About 4mm before twisting
About less than 2mm after twisting
Screw
Bushing
Sign plate
Screw nut
Figure 2 Figure 3
Figure 6
7
Connection between the water inlet hose and the washer
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose and the water
inlet hose
Check the connection between the jointer of the water inlet hose and
the water faucet
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
1.Push down the slider. Insert the water inlet hose into the jointer.
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Locking lever
Slider
water absorption
cushion.
nut of the water
inlet hose
the jointer of the
water inlet hose
Slider
Locking lever
jointer of the
water inlet valve
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
8
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose. Open the
water faucet.
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. The earth terminal shall not link
to gas pipeline and faucet water pipeline.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Check if
the laundries
has special
requirement
on washing
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
4.slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally
Andere Handbücher für HWM65-728
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Haier Waschmaschine Handbücher
Haier
Haier WD-8888-19 Bedienungsanleitung
Haier
Haier TEL6TL Bedienungsanleitung
Haier
Haier XQJ50-31 Bedienungsanleitung
Haier
Haier AWT-120LI Bedienungsanleitung
Haier
Haier HWM-6.5/S Bedienungsanleitung
Haier
Haier HMS1060TVE Bedienungsanleitung
Haier
Haier HW-C1070TVEME Bedienungsanleitung
Haier
Haier HW70-B1239N Bedienungsanleitung
Haier
Haier JW-PK60A Bedienungsanleitung
Haier
Haier JW-G50A Bedienungsanleitung
Haier
Haier HLP24E Bedienungsanleitung
Haier
Haier HW-C1260TVE-E Bedienungsanleitung
Haier
Haier HWM75-78 Bedienungsanleitung
Haier
Haier HW80-IM12826TNZP Bedienungsanleitung
Haier
Haier HVS1200 Bedienungsanleitung
Haier
Haier HN800TX Benutzerhandbuch
Haier
Haier XQB60-68 Bedienungsanleitung
Haier
Haier HWD1600 Bedienungsanleitung
Haier
Haier HWM-G42A Bedienungsanleitung
Haier
Haier HW80-B14266A Bedienungsanleitung
