Haier HWM80-68B Bedienungsanleitung

Full automatic washing machine

User's manual

This manual is for

HWM80-68B

Please read this manual

carefully before using.

Retain it for future reference.

Names of the parts

Safety precautions

Contents

Answers to question

Trouble shooting

Packing list Specification

Installation and adjustment

Usage of the drain hose

Preparation before washing

Put in the laundries

Add the detergent and softener

Use the operation knobs and buttons

Installation the water inlet hose

Disposal after washing

Finish washing

Close the top lid

Please check if the power receptacle has good earthing

condition before using to guarantee your safety.

Warning sign

Names of the parts

Meaning and description of the symbols

Forbidding sign

Contents marked with that symbol are related

to the safety of the product and the personal

safety of the users. Please operate in strict

conformity to the contents, otherwise it may

cause damageof the machine or injure the

personal safety of the user.

Contents marked with that symbol are actions

forbidden to perform. Performing of those

actions may result in damage of the machine

or injure the personal safety of the user.

Adjustable foot

Front control

board

Front fixed

foot

Rear fixed foot

back cover

Cabinet

Drain hose

Back faceplate

Control panel

film

Control panel

Lint filter(Installed by user)

Filter cover

Level meter

Power line

Pulsator

Inner tub

Detergent box Drier outlet

cover

Top lid B

Cabinet handle

Globe cover

Cool water valve

Top lidA

Adjustable foot

seam

hanging hole

for the drain

hose

Safety precautions

Please insert the power cord into

special receptacle with rated vol-

tage.Be sure to use single-phase

three pins receptacle.The earthing

terminal of the receptacle must be

earthed reliably.If possible,please

adopt electric leakage protector.

When the machine is normally

using, please put the power plug

at the location easily to be insert-

ed and extracted by hand. Be sure

to pull the plug off when there's

power failure, or the machine is

being moved, cleaned or when it

is idle.

If the power cord is bad, to avoid risk it is required to replace it by the

technicians of our special shop or the after-sale service department.

Keep the pin of the power plug clean.

Do not put the machine at damp

place like the bathroom . Never

wash it with water. Do not place

wet laundries on the control panel.

Do not use water hotter than 65 C .

In case the washing machine is in-

stalled on ground with carpet, do not

block the ventilation hole with carpet.

The ventilation holes

at the bottom

Do not wash water-proof laundries like

the raincoat, bike covers etc. to avoid

abnormal vibrations in spinning.

Do not let the machine share one receptacle

with other electric appliances. If the power

plug is damaged, or the plugging into the

receptacle is loose, do not use the plug any

more.

Earth

Do not decompose, repair or alter the

machine by yourself.

Do not put any hot or heavy items (such

as the kettle with hot water ) on the

washing machine.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.)

The handicapped or children without

care shall not use the machine.

Keep the machine away from direct

sunlight and heat source like the heater.

Safety precautions

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Petrol

Thinner

To protect your laundries and wash-

ing machine, please take out all of the

coins, buttons, sand, hairpin and

other foreign materials before washing.

Please check if the water faucet is open,

and if the connection of the water inlet

pipe is proper.

It is suggested to use foamless washing

powder.

Toprevent the lintin the tubfrom blocking

the cascade outlet and influencing the

cascade effect, please keep the lint filter

in good condition, and install it to proper

position during washing.If the lint filter is

lost or damaged,please contact thelocal

after-sale service department of our

company.

Install the bottom plate

Adjust the installation position

Soft items

Bottom plate Screw

Installation and adjustment

Please install and adjust the machine according to the requirement of the manual. It is

very important to your security and correct operating the machine.

Back

Front

After openingthe package, pleaselean the

washing machine gently down on soft items

(like towel cloth, blanket, etc.). Install the

bottom plate to the bottom of the machine

with eight screws by a cross screwdriver,

then lift the machine up gently. See to the

figure:

Loosen Fasten

High Low

Adjustable nut

Adjustable leg

The largest allowable slope of the shank base of the machine is 2 .

The slanting or rough ground will result in unstable running or

stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal:

Adjust the adjustable leg:

If the bulb of the level meter at the balance display

position is inside the standard circle, it indicates that

the machine is horizontal. Otherwise you need to

adjust the adjustable leg of the machine.

1.To twist the adjustable leg, please first lift up the

leg side slightly, loosen the adjustable nut, and

then twist the leg.

2.After adjustment, fasten the nut.

Air bubble

Standard circle

Suitable Not suitable

Inner tub Lint filter

After openingthe package, pleasetake out thelint

filter from the document bag,install it tothe filter cover

of inner tub.See to thefigure.

How to change the direction of the drain hose

1.The height of the drain hose shall be

less than 10cm, or the drainage will not

be smooth, and cost such long time that

the machine may stop at mid way.

2.Do not ramp or press the drain hose.

3.If the drain hose is too long, cut it at mid

point. To make smooth drainage, cut the

front end of the hose slantingly.

4.If extra drain hose is needed, please

make separate purchase. The inner

diameter of the extra hose shall not

less than 30mm, and the length shall

not exceed 1.5m.

Usage of the drain hose

The drain hose shall drain smoothly

1.Dismount the back cover of the washing machine.

2.Lay down the washing machine gently with the front

side facing the ground. Use cross screwdriver to

loosen the eight screws. Take off the bottomplate.

4.Dismount the protecting cover of the drain outlet at the

other side as indicated in Figure 3.

5.Extend the drain hose out of the other side. Fix the drain

hose onto the cabinet with the drain hose rack. Set the

drain hose nut on, and fasten the nut to the direction

indicated in the figure, as per Figure 4.

6.Install the protecting cover of the drain outlet to the other

side, as indicated in Figure 5.

7.Install the bottom plate (method the same as stated

above). Lift up the washing

machine gently.

3.Put down the outer drain hose. Twist the drain hose nut

counterclockwise to take it off as indicated in Figure 1.

Take off the drain hose rack. Put the drain hose into

the cabinet as indicated in Figure 2.

back

front

bottom plate

drain outlet

protecting

cover fasten

drain hose nut

Drain hose nut Drain hose rack

Outer

drain hose

Loosen

soft item

Figure 1

Figure 3 Figure 4

Figure 5

Figure 2

If the extra hose is too long, cut it either

at point A or B.

Install the lint filter

Install the water inlet pipe

Connection between the water inlet hose jointer and the water faucet

Water faucet, suitable water faucet, not suitable

It is required that the front end shall be longer than 10mm.

The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.

2. Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose

jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four

screws and take out the bush inside the jointer. See to Figure 3.

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

3. Fasten thefour screws ofthe water inlethose jointer evenly. See toFigure 4.

About 4mm after twisting

Remark: .Before installation, the threading is 4mm above the upper surface of the nut.

After installation, the threading is 2mm above the upper surface of the nut..

About above 2mm after twisting

Water inlet hose jointer

Screw knife

Screw

Bushing

Nameplate

Screw nut

Water inlet hose Figure 1

Figure 4

Figure 2

Figure 5

Figure 3

Figure 6

Slider

Lock level

Install the water inlet hose

4. Take off the nameplate.Twist the fastening nut as per the indication of the figure

to seal up the exit end face of the faucet. See to Figure 5.

Connection between the water inlet hose and the washing machine

1 Do not takeoff the waterabsorption cushion. Pleasecheck

if the cushion isdropped or damaged eachtime before using.

If it happens so,please duly contact ourafter-sale service

department.

2 Set the nutof the water inlethose on the waterinlet valve jointer.

3 Fasten the nut.Swing it gently toconfirm if it's fastenedwell.

Water absorption cushion.

Water inlet

hose nut

Water inlet valvejointer

Dismount the water inlet hose

Connection between the water inlet hose jointer and the water inlet hose

Check the connection between the water inlet hose jointer and the

water faucet

1.Swing the hosegently to checkif it is fastened stably.

2.After installation, open thefaucet to check ifit leaks water.

3.Do not bend thehose by force.

4.Each time before using,please check if theconnection

between the water inlethose jointer and thewater faucet,

and the installation ofthe water inlet hoseisfirm, so as

to avoid dropping owingto improper installation.

1. Push downthe slider.Plug the waterinlet hose intothe jointer.

2. Hang thelock lever ontothe jointer.Release

the slider tilla click soundis heard.

Lock level

Slider

The water inlet

hose jointer

Slider

Locking level

1. Close thewater faucet.

2 .Press thelock lever andpush down theslider. Thenpull off the

water inlet hose.If the machineis used more than once every

week, the waterinlet hose jointercan remain onthe faucet to

avoid damaging thefastening screws.

1 Preparation before washing

Preparation before washing

1.Connect the water inlet hose. Open

the water faucet.

2.Confirm that the washing machine is

earthed reliably. Then insert the

power plug into the receptacle. The

earth terminal shall not link to gas

pipeline and faucet water pipeline.

3.Put down the drain hose.

Pay attention to followings before washing the laundries

Check if

the laundries

has special

requirement

on washing

Clear the

pocket. Take

out the coins,

sand, hairpins

etc.

Tie the long

strips; fasten

the buttons;

close zippers.

When the pulsator

is running , the

buttons of the

laundries may

cause noise. For

the sake of

discretion, please

put the laundries

with buttons into

other laundries.

The quantity of

the laundries

shall not be too

large. Stretch

and loosen the

laundries before

putting them in

the tub.

a. Check if the laundries are applicable for washing with machine.

b. Divide the laundries that are not colorfast from other laundries.

c. Put those laundries difficult to absorb water into water with hand.

d. For those laundries with heavy soil, please first remove the dirt like

mud or dust. For the parts with heavy soil, please apply detergent on

them in advance, which can make it easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn

it over before putting in.

f. Do not put those laundries polluted by chemicals into the washing

machine directly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Haier Waschmaschine Handbücher

Haier

Haier HWM130-0523S Bedienungsanleitung

Haier

Haier JW-K71A Bedienungsanleitung

Haier

Haier HLP20E - Pulsator Washer Bedienungsanleitung

Haier

Haier XQB55-10 Bedienungsanleitung

Haier

Haier HWM80-0626S Bedienungsanleitung

Haier

Haier HWM120-0523S Bedienungsanleitung

Haier

Haier AC-8888-07 Bedienungsanleitung

Haier

Haier HW90-BP14959S6 Bedienungsanleitung

Haier

Haier HWM75TL Bedienungsanleitung

Haier

Haier HW150-BP14986ES9 Bedienungsanleitung

Haier

Haier HWM33-200F Bedienungsanleitung

Haier

Haier HWM80-27S Bedienungsanleitung

Haier

Haier HW-D1270TVE ME Bedienungsanleitung

Haier

Haier HWM105-0626S Bedienungsanleitung

Haier

Haier HWM40-32 Bedienungsanleitung

Haier

Haier HNY500TX Bedienungsanleitung

Haier

Haier HWM85-0713SW Bedienungsanleitung

Haier

Haier ESL-T21 Bedienungsanleitung

Haier

Haier HW80-1403D Bedienungsanleitung

Haier

Haier XQG50-QF800 Bedienungsanleitung

Haier

Haier HWM90-0577 Bedienungsanleitung

Haier

Haier HQM62-K Bedienungsanleitung

Haier

Haier HWM130-113S Bedienungsanleitung

Haier

Haier HW110-B14979EU1 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung