Hakko Electronics FG-101B Bedienungsanleitung

Thank you for purchasing the HAKKO FG-101B Soldering tester.

This product is a soldering iron tester capable of measuring soldering tip

temperature, leak voltage and ground resistance.

Please read the manual carefully

before operating the HAKKO FG-101B.

Please keep this manual readily accessible for reference.

Instruction Manual

SOLDERING TESTER

FG-101B

Table of Contents

1. PACKING LIST AND PART NAMES .........................................................................................1

2. SPECIFICATIONS......................................................................................................................2

3. WARNINGS, CAUTIONS AND NOTES.....................................................................................3

4. OPERATION ..............................................................................................................................4

4-1 Initial setup........................................................................................................................................... 4

4-2 Measurement of tip temperature........................................................................................................ 5

4-3 Measurement of leak voltage ............................................................................................................. 6

4-4 Measurementofresistancedi󰀨erencebetweentipandgroundwire ............................................ 7

4-5 Explanation about various functions ................................................................................................ 7

5. MAINTENANCE.........................................................................................................................9

6. REPLACEMENT PARTS/OPTIONS ........................................................................................10

1. PACKING LIST AND PART NAMES

Please check that all items listed below are included in the package.

HAKKO FG-101B ............................................1

Fuse.................................................................1

Conductive wire...............................................1

Sensor (qty 10)................................................1

Ground clip ......................................................1

Power cord ......................................................1

Instruction manual ...........................................1

SYSTEM TESTER

FG-101B

Fuse Conductive

wire

Ground clip

Blind plate

Power receptacle

LCD

AUTO ZERO button

MAX HOLD

button

SELECT button

Conductive plate Power switch

Power cord

Protective plate

Mode display

Ground terminal (GND)

Sensor

AUTO/SEND

button

Display contents

*1 This alarm indicates sensor burnout.

If this alarm occurs, replace the sensor.

*2 When the and buttons are held pressed simultaneously for a long time (1 sec or longer), the count

is reset.

Temperature measurement count*2

°C/°F/mV/Ωdisplay

AUTO HOLD function

MAX HOLD function

Calibration

Display temperature, leak voltage and

tip to ground resistance/

Burnout alarm*1

(Display of "-1" indicates burnout.

CAUTION

Do not use this product for a soldering iron which is not grounded.



Connect this product to a power receptacle equipped with a ground terminal and ground it before use.

Instruction manual

DATA I/O connection (9 pins)

Infrared output part

Inlet

HAKKO FG-101B

2. SPECIFICATIONS

Model name HAKKO FG-101B

Temperature Resolution 1˚C 1°F

Measurement range 0 - 700˚C*1 32 - 1300°F*1

Measurement

tolerance

±3

˚C

(between 300 and 600

˚C

)

±5˚C (other than above)

±6

°F

(between 572 and 1112

°F

)

±10°F (other than above)

Sensor K(CA) thermocouple

Voltage Resolution 0.1mV

Measurement range 0 - 40 mV (AC)

Measurement tolerance

±(5% of reading +1 digit)

Resistance Resolution 0.1Ω

Measurement range 0 - 40Ω

Measurement tolerance

±(5% of reading +1 digit)

Display LCD display 3-1/2 digits

Burnout *2

MAX HOLD function Refer to "MAX HOLD Function"(page 7) in "4-5

Explanation about various functions".

AUTO HOLD function Refer to "AUTO HOLD Function"(page 8) in "4-5

Explanation about various functions".

Temperature

measurement count

function

000 to 999 times

Power consumption 100V : 3.2W 100 - 110V : 3.6W

120V : 3.2W 220 - 240V : 3.6W

Outline dimensions 211(W) × 53(H) × 126(D) mm

Weight 0.95 kg

Usable temperature/humidity range 0 to 40˚C, Max. 80%RH, without condensation

Environmental conditions Applicable rated pollution degree 2

(According to IEC/UL61010-1)

*1 Temperature sensors (191-212) can only be used to measure temperatures below 500°C (932°F). To

measure higher temperatures, use an appropriate temperature probe (see"6. REPLACEMENT PARTS/

OPTIONS").

*2 If the temperature sensor is not attached or is disconnected, "Burnout" will appear. If the temperature sensor

is disconnected, replace it with a new one. In addition, if a value out of the temperature range is detected.

"Burnout" will also appear.

NOTE

Please note that the specications and appearance are subject to change without prior notice.

3. WARNINGS, CAUTIONS AND NOTES

In this manual, items requiring caution are classied into 2 categories, "WARNINGS" and

"CAUTIONS", as dened below. Please make sure to understand these items before reading

the main text.

WARNING :

Failure to comply with a WARNING may result in serious injury or death.

CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage

to the objects involved.

NOTE : Indicates important steps or items in the procedure being explained.

Be sure to observe the following warning items.



WARNING

󱾀The unit is for a counter or workbench use only.

󱾀This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in safe way and understand the

hazards involved.

󱾀Children shall not play with the appliance.

󱾀Cleaning and user maintenance shall not be made by children without supervision.

Be sure to observe the following warning items, for which failure to do so may cause

accidents or malfunctions.



CAUTION

󱾀This unit is for indoor use only.

󱾀When using the thermometer to measure the temperature of the soldering iron tip or desoldering

nozzle, pay great attention to the temperature of the tip or nozzle since it will be as high as 200 to

450°C (392 to 842°F). Careless handling of such a hot object may result in a burn or re.

󱾀Do not modify this product.

󱾀Do not get this product wet or use it with wet hands.

󱾀Be sure to unplug the power plug before internal inspection or replacement of parts. Failure to do so

may cause an electric shock.

󱾀Use HAKKO genuine parts as replacement parts.

󱾀When inserting or unplugging the power plug, do so while holding the plug, not the cord.

󱾀Do not perform dangerous actions.

4. OPERATION

CAUTION

Since the sensor is made of ultra-

thin (Ø0.2) K thermocouple, pressing

the sensor strongly may cause it to be

disconnected. Handle it with care.

Slide pin

Conductive plate

Slide button

Terminal

4-1 Initial setup

1. Attach the included sensor.

1) Slide the slide button. The slide pin

will move toward the terminal.

2) Attach the sensor with the slide pin

moved toward the terminal.

3) Attach the sensor having a red mark

to the red-colored terminal and the

sensor having a blue mark to the

blue-colored terminal.

2. Insert the power plug into the power

receptacle and turn on the power switch.

1) Be sure to connect the main body

power cord to a two-pole grounded-

type receptacle.

2) The power receptacle of the HAKKO

FG-101B main body supplies power

only when the power switch is turned

on.

CAUTION

• Since the main body is partially

made of resin, be careful not to

touch the tip to the main body. In

addition, also be careful not to

touch the tip to the terminal or the

slide pin.

• Although the measurement point

of the sensor undergoes special

treatment, it will deteriorate

gradually due to repeated

measurements. In order to measure

the temperature correctly, if the

measurement point is worn out,

replace the sensor with a new

one. The reference number for

sensor replacement is approx. 50

measurements.

• When ux is stuck on the terminal,

wipe it o󰀨 with alcohol. (Do not use

thinner or benzin for wiping.)

• Read the values when the display

temperature is stable.

CAUTION

Do not measure the temperature by applying

hot air (HAKKO FR-811, etc.) directly to the

HAKKO FG-101B. If hot air is applied directly,

the HAKKO FG-101B will be damaged.

4-2 Measurement of tip

temperature

1) Press the SELECT button to set the

mode to "TEMP".

2) Apply a new coat of solder on

the tip and touch it on the sensor

measurement part (See the gures at

right.)

New solder

Measurement

point

Tip

NOTE:

When measuring, apply a new coat of solder on the tip. This action is required to ensure

that the conductive plate comes in rm contact with the tip.

NOTE :

If solder can't wet easily on the conductive plate due to low tip temperature or because of

the tip having small thermal capacity, use the included conductive wire.

Replacement method

Remove the 2 screws attaching the conductive plate, replace the conductive plate with the

conductive wire, and then attach the conductive wire with the removed screws.

4. OPERATION(continued)

NOTE :

During measurement of leak voltage, even

when the tip is not applied to the conductive

plate, values are displayed; however, this is

not a malfunction of the product. In addition,

when values out of measurement range are

detected, burnout will be displayed, and this is

also not a malfunction.

1) Plug the power plug of the soldering

iron to be measured into the power

receptacle the HAKKO FG-101B

main body.

2) Wait until the tip reaches the

set temperature. If the soldering

iron temperature is variable, set

temperature to maximum.

3) Press the SELECT button and

change the mode to "mV".

4) Press the button.

Refer to " AUTO ZERO function"

(page 8) in "4-5 Explanation about

various functions".

5) Clean the tip and apply a new coat of

solder on the tip.

6) Apply a coating of solder to the center

of the conductive plate and heat it

until a good soldering wet condition is

achieved.

7) When the display temperature is

stable, read the values.

4-3 Measurement of leak voltage

CAUTION

• Before measuring the voltage or resistance, be sure to connect the main body

power cord to a two-pole grounded-type receptacle.

• If values exceeding specied ones are displayed as results for voltage or

resistance, check the tip and attaching screws of the soldering iron for looseness

and take another measurement.

"MAX HOLD"

disappears

indicating the

function is

cancelled.

MAX HOLD

Press the button for

1 second or more

Max. temperature is updated.

Press the

less than 1 second

button for

Press the

less than 1 second

button for

MAX HOLD

MAX HOLD function (Temperature

measurement only)

Quickly pressing the button will cause "MAX

HOLD" to be displayed at the bottom of the

screen. As long as "MAX HOLD" is shown, the

maximum temperature will stay displayed.

Operation method

 Pressed quickly (less than one second)

"MAX HOLD" is displayed at the bottom

of the screen.



Pressed quickly (less than one second)

("MAX HOLD" is displayed )

By pressing the button quickly, the

displayed value will be reset and the

maximum temperature after pressing the

button will be displayed.



Pressed for a long time (1 second or

longer)

The MAX HOLD function will be released

and the product will return to normal

display.

CAUTION

 Turning o󰀨 the power always cancels the

MAX HOLD function.

The MAX HOLD function can only be used

during the temperature measurement.

HAKKO FG-101B can use the following functions.

4-4 Measurement of resistance di󰀨erence between tip and ground wire

4-5 Explanation about various functions

1) Plug the power plug of the soldering iron to be measured into the power receptacle the

HAKKO FG-101B main body.

2) Wait until the tip reaches the set temperature. If the soldering iron temperature is variable,

set temperature to maximum.

3) Press the SELECT button and change the mode to "OHM".

4) Press the button. {Refer to " AUTO ZERO function" (page 8) in "4-5 Explanation

about various functions".}

5) Perform the measurement in the same procedure as "4-3 Measurement of leak voltage".

AUTO ZERO function

AUTO ZERO function is necessary for measureing voltage (mV) and resistance (OHM).

Pressing the button displays "counting": 0.0.0 →0.0 →0.

Wait until the normal display appears.

Correction values from AUTO ZERO are recorded in the main body. Even after the power is

turned o󰀨, the correction values are still available in later measurement sessions.

Before using this function, it is necessary to cancel the "AUTO HOLD" displays.

AUTO HOLD function

When the button is pressed quickly (less than one second), "AUTO" will blink at the lower

right of the LCD.

While "AUTO" is blinking, touch the soldering iron tip to the sensor. (temperature)

While "AUTO" is blinking, touch the soldering iron tip to the conductive plate. (mV, OHM)

"AUTO" will stop blinking and stay lit after a certain amount of time, and the xed

measurement result will be displayed.

Even after the xed result is displayed, applying the tip to the sensor or the conductive plate

will enable the AUTO HOLD function to work again.

Each time the button is pressed, the AUTO HOLD function toggles between ON and OFF.

The AUTO HOLD function does not assume the measurement by temperature probes such

as the hot air.

Data send function (infrared)

Press the button for longer than one second.

Temperature data will be sent by infrared output

from the upper part of the HAKKO FG-101B. The

temperature display will blink during sending.

The temperature send function can send data only

to machines capable of receiving the data.

Only xed values can be sent.

In order to send xed values, the AUTO HOLD function or MAX HOLD function can be used

for temperature measurements and the AUTO HOLD function can be used for voltage or

resistance measurements.

Make sure the HAKKO FG-101B infrared output part is facing and within the reception range

of the receiver.

Count function

When a sensor detected a sudden temperature

rise more than 100 degrees Celsius, the value of

the thermometry count Increases.

When resetting the count number, push the

button and the button for more than one

second at the same time.

4. OPERATION(continued)

Temperature measurement count

受信部

受信範囲

赤外線出力部

赤外線出力方向

Receiver

Infrared output

direction

Infrared output part

Receiving

scope

Inhaltsverzeichnis

Andere Hakko Electronics Prüfgeräte Handbücher

Hakko Electronics

Hakko Electronics FG-101 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG101-16 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG-465 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 192 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG-460 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-811 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG101B-03 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG-470 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-410 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FG-470 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung