Halo Board Halo Go Bedienungsanleitung
HALO GO
TM
Before You Begin---------------------01
Main Components-------------------02
Charging Your Batteries------------03
Powering on the Halo Go----------04
Indicator Lights ----------------------05
Pairing your Bluetooth Device----06
Riding Your Halo Go-----------07-10
Safety Alerts--------------------------11
Driving Safety--------------------12-15
Technical Specications-----------16
Battery Safety--------------------17-18
Before You Begin
Before You Begin
Before learning to ride your Halo Go, you must read and follow all instructions and warnings in
this user manual. It is important that you follow all safety warnings and cautions that appear
throughout the user manual and that you use good judgment when you ride your Halo Go.
The Risk of injury
The Halo Go is a self-balancing, personal scooter that uses balancing technology. Balancing
technology cannot prevent injury if you do not ride the scooter safely. Whenever you ride the
scooter , you risk death or serious injury from loss of control, collisions, and falls. To reduce risk
of injury, you must read and follow all instructions and warnings in the user manual.
01
NOTE: The Halo Go comes with Ride-Assist Technology that keeps the board balanced at all
times. This technology requires the board to be placed on a surface while powered on. Do NOT
pick up the Halo Go while it is still on if Ride-Assist is turned on. Always power o the board prior
to picking up. Failure to do so will cause the System Warning Indicator to sound and the board
will need to be powered o and back on again before you can ride (learn more - page 8-9).
Main Components
02
Foot Mat
1
11
3 3
54
2
Indicator Lights
2
Headlights
3
Power Button 4
Charging Port 5
Charging Your Batteries
Battery Charge Indicator Light
When scooter is plugged in and charging, battery charge indicator will be solid red.
When the battery charge indicator turns green, the batteries are fully charged.
03
1
3
2
Do NOT insert the power cord plug if the charge
port, power cord or AC power outlet is wet.
Powering On the Halo Go
Power on your scooter by pressing the Power button. The Power button is located on the back
side of the scooter . The indicator lights will illuminate to indicate the power is ON.
Resetting and Calibrating the Halo Go
Put the scooter on a level surface where the wheels do not make contact with the ground.
Press the Power Button for 3-5 seconds until caution light ashes.
Turn OFF the scooter and turn ON again.
Powering On the Halo Go
04
1
1
3
2
2
Power Button Caution Light
Warning Indicator Light (Red)
If red warning light is ashing, there is an issue with the scooter (low battery, over speed,
power issue, etc).
Indicator Lights
05
1
Balance Indicator Light (Green)
The scooter is in Balance Mode with rider on.
1
Battery Status Indicator Light (Green)
When powered on, the battery status indicator light will turn on solid green.
2
Pairing your Bluetooth Device
06
Make sure both the Bluetooth® function on your device and the scooter are turned on.
On your device, locate the Bluetooth® device list.
Select “Halo Go Music” from the list to pair.
1
2
3
To pair with a Bluetooth®device
follow these steps:
To reset Bluetooth®Memory, you must reset
the scooter. Refer to Resetting the
Halo Go (page 4).
Resetting Bluetooth®Memory
Speaker
07
Before riding, make sure your Halo Go is charged. Inspect your scooter before each use. Do not ride
if any part is loose or damaged. The Scooter is highly maneuverable and allows you to easily navigate
around obstacles. However, to prevent the loss of traction, you must always be careful when riding
and learn to identify and avoid unsafe surfaces. Slippery, icy, or wet surfaces, loose materials
(sand/gravel), steep slopes, and obstacles might aect the Halo Go’s performance. Familiarize
yourself with the indicator lights that may be displayed on the scooter (page 5).
Step 1. Power ON the Halo Go by pressing the power button. Make sure the
Battery Status Indicator light is on.
1
2
Riding Your Halo Go
The Halo Go includes proprietary Halo Ride-Assist Technology Sensors.
When powered on, the Rover will automatically lift itself into a balanced position
and will remain upright until powered off. Do NOT pick up the board while the board
is on if Ride-Assist Technology is turned on (see Page 9 to turn off this feature).
Inhaltsverzeichnis
Andere Halo Board Hoverboard Handbücher
