Halstrup-walcher REG 21 Bedienungsanleitung

Instruction Manual

REG 21 Pressure

Regulator

halstrup-walcher GmbH

Stegener Straße 10

D-79199 Kirchzarten

Germany

Phone: +49 (0) 76 61/39 63–0

Fax: +49 (0) 76 61/39 63–99

E-Mail: info@halstrup-walcher.com

Internet: www.halstrup-walcher.com

Document 7100.003674 07/2018

Instruction Manual REG 21

Table of Contents

1Safety precautions ..........................................................................................................4

1.1 Appropriate use...............................................................................................................4

1.2 Shipping, assembly, electrical connections and start-up..................................................4

1.3 Troubleshooting, maintenance, repairs, disposal.............................................................4

1.4 Symbols..........................................................................................................................5

2Instrument description.....................................................................................................6

3 Start-up............................................................................................................................6

3.1 Features..........................................................................................................................6

3.1.1 Inputs and outputs...........................................................................................................6

3.1.2 Display elements.............................................................................................................7

3.1.3 Keypad............................................................................................................................7

3.1.4 Menue tree......................................................................................................................8

3.2 User functions..................................................................................................................9

3.3 Device parameters...........................................................................................................10

3.4 Switching behaviour.........................................................................................................11

3.5 Zero-point calibration.......................................................................................................12

3.5.1 Sequence of zero-point calibration steps.........................................................................12

3.6 Overload protection .........................................................................................................12

4Identification....................................................................................................................13

4.1 Included in shipment........................................................................................................13

4.2 Product labelling..............................................................................................................13

4.3 Models.............................................................................................................................13

5Electrical connections and installation.............................................................................14

5.1 Installation .......................................................................................................................14

5.2 Instrument connections....................................................................................................14

5.2.1 Pressure ports.................................................................................................................14

5.2.2 Electrical connections......................................................................................................15

5.2.3 Option light emitting diodes (LED)...................................................................................15

6Start-up...........................................................................................................................16

6.1 Setting parameters ..........................................................................................................17

6.1.1 Overview of parameter setting functions and parameters................................................17

6.1.2 Launching a parameter setting function...........................................................................18

6.2 Setting parameters ..........................................................................................................18

6.2.1 Notes on setting switching value parameters. .................................................................20

7Troubleshooting ..............................................................................................................21

8Technical data.................................................................................................................22

9Dimension drawings........................................................................................................24

10 Certificate of Conformity..................................................................................................25

Instruction Manual REG 21

Purpose of instruction manual

This instruction manual describes the features of the REG 21 pressure regulator and

provides guidelines for its use.

Improper use of this instrument or failure to follow these instructions may cause injury

or equipment damage. All individuals responsible for operating this instrument must

therefore be properly trained and aware of the hazards, and must carefully follow

these operating instructions and the safety precautions detailed within. Contact the

manufacturer if you do not understand any part of this instruction manual.

Handle this manual with care:

It must be readily available throughout the lifecycle of the instrument.

It must be provided to any individuals who assume responsibility for operating the

instrument at a later date.

It must include any supplementary materials provided by the manufacturer.

The manufacturer reserves the right to continue developing this instrument model

without documenting such development in each individual case. The manufacturer

will be happy to determine whether this manual is up-to-date.

Conformity

This instrument corresponds to the state of the art and meets all legal requirements

set forth in EC directives as evidenced by the CE label.

The manufacturer owns the copyright to this instruction manual. This manual contains

data, instructions and drawings pertaining to the features and usage of this

instrument; copying this manual in part or in full or distributing it to third parties is

prohibited.

Instruction Manual REG 21

1 Safety precautions

1.1 Appropriate use

The REG 21 pressure regulator is designed for measuring, displaying, monitoring and

regulating positive and negative overpressures and differential pressures of non-

aggressive, gaseous media.

Always observe the operating requirements—particularly the permissible supply

voltage—indicated on the rating plate and in the “Technical data” section of this

manual.

The instrument may only be handled as indicated in this manual. Modifications to the

instrument are prohibited. The manufacturer is not liable for damages caused by

improper use or failure to follow these instructions. Violations of this type render all

warranty claims null and void.

1.2 Shipping, assembly, electrical connections and start-up

Do not close the pressure input ports when shipping, as changes in barometric

pressure could damage instruments with low measuring ranges.

Only technical personnel who are appropriately trained and authorized by the

operator of the facility may assemble the instrument and set up its electrical

connections.

The instrument may only be operated by appropriately trained individuals who have

been authorized by the operator of the facility.

Pressurized air or breath is not to be used for performance tests, as this could

damage instruments with low measurement ranges.

Measurement errors may occur if the instrument is not kept protected from sunlight.

Specific safety precautions are given in individual sections of this manual.

1.3 Troubleshooting, maintenance, repairs, disposal

The individual responsible for the electrical connections must be notified immediately

if the instrument is damaged or if errors occur.

This individual must take the instrument out of service until the error has been

corrected and ensure that it cannot be used unintentionally.

Always unplug the power cord before opening the instrument!

This instrument requires no maintenance.

Only the manufacturer may perform repairs that require the housing to be opened.

Instruction Manual REG 21

The electronic components of the instrument contain environmentally hazardous

materials and materials that can be reused. For this reason the instrument must be

recycled in accordance with the environmental guidelines of the jurisdiction in

question once it has been taken permanently out of service.

1.4 Symbols

The symbols given below are used throughout this manual to indicate instances when

improper operation could result in the following hazards:

WARNING! This warns you of a potential hazard that could lead to bodily injury up

to and including death if the corresponding instructions are not followed.

WARNING: This warns you of a potential hazard that could lead to significant

property damage if corresponding instructions are not followed.

INFORMATION: This indicates that the corresponding information is important

for operating the instrument properly.

Instruction Manual REG 21

2 Instrument description

The REG 21 pressure regulator measures differential pressures between its two

pressure ports, which lead to two chambers of a pressure measurement capsule.

Pressure is measured via a beryllium bronze membrane spring, which is displaced by

the pressure difference between the two chambers. Inductive displacement

transducers measure membrane deflection without contacting the membrane. The

instrument has no frictional parts or parts subject to mechanical wear, and performs

the following tasks:

Displays the measured value

Provides the voltage (current is also an option) proportional to the measured value.

Its two switching outputs make it suitable for use as either a two-point or a three-point

controller

The following are some additional features worth highlighting:

Overload protection

Adjustable switching hysteresis

High level of sensitivity

High level of accuracy and long-term stability

Automatic zero-point correction

Low temperature dependence

3 Start-up

3.1 Features

3.1.1 Inputs and outputs

Fig. 1: basic circuit diagram

Power supply: Depending on the model, the power is supplied as either 230 V-AC,

115 V-AC, 24 V-AC or 24 V-DC. The details of the supply voltage are given on the

rating plate.

Pressure ports: (-) port: reference pressure; (+) port: pressure to be measured.

The measurement range is given on the rating plate.

Analogue output: The instrument produces a voltage output proportional to the

measured pressure. Output is in the range of 0...10 V (ranges of -5…+5 V, 4...20

mA or 0...20 mA are optional). The spread of the analogue output values is

proportional to the measurement range. The type of analogue output is indicated on

the rating plate.

power supply

pressure

ports

analog output

switching output 1

switching output 2

Instruction Manual REG 21

Switching outputs 1 and 2: The instrument comes equipped with 2 relay outputs (2

transistor outputs are also an option). The type of switching output is indicated on

the rating plate. Switching outputs are triggered when values exceed and/or fall

below switch-on and switch-off values. See section 3.4 for a more detailed

description of switching behaviour. The instrument utilizes changeover relays and

bipolar NPN transistors, making it possible to create either open-collector or open-

emitter circuits.

Fig. 2 Transistor output (optional) a) open-collector circuit b) open-emitter circuit

3.1.2 Display elements

Fig. 3 Front view of the instrument

Display: The display shows the measured differential pressure or overpressure in

the units indicated on the housing next to the display. Positive values are displayed

as is; negative values are indicated by a preceding minus sign.

LED 1: LED 1 shows the status of switching output 1 and is illuminated whenever

the switch-on value exceeds or falls below that set for switching output 1 (see fig. 5).

LED 2: LED 2 shows the status of switching output 2 in a way analogous to that of

output 1.

3.1.3 Keypad

The instrument is set by means of 4 keys, whose functions are described in the

following:

Set key:

Call up and exit parameter setting and display functions

Save parameters

Enter key:

Begin and end settings

Select decimal places and +/- sign

Select key:

Select values or parameters

Set numerical values

Table 1

LED 1

LED 2

digital

input

digital

input

Instruction Manual REG 21

Basic settings

Time constant

(1,2,5 and 10 sec.; Default: 1)

brightness

(1 to 15; Default: 5)

zero adjustment

(autom./manuell; Default: manuell)

Change the

parameters of

switching output 1

Change the

parameters of

switching output 2

Display of the

parameters of

switching output 1

Display of the

parameters of

switching output 2

Starting manual zero adjustment

Switch-on value

(0 to 100%; Default: 35%)

switch-of value

(0 to 100%; Default: 15%)

switch direction

(0 and 1; Default: 0)

Switch-on value

switch-of value

switch direction

Switch-on value

switch-of value

switch direction

Switch-on value

(0 to 100%; Default: 50%)

switch-of value

(0 to 100%; Default: 10%)

switch direction

(0 and 1; Default: 0)

3.1.4 Menue tree

Instruction Manual REG 21

3.2 User functions

User functions include setting device parameters, displaying switching output

parameters and manually performing a zero-point calibration.

Users call up these functions by pressing the set keys; the specific function called up

depends on whether the keys are pressed individually or in combination, and for how

long they are pressed. Moving decimal points indicate that the instrument is no longer

displaying measured values (see fig. 7).

Function

parameter setting

Key sequence

Parameter

basic settings

press both and

hold for <2 s*

Time constant

Brightness

Zero adjustment

(see section 6.1)

setting parameters for

switching output 1

hold for >2 s**

Switch-on value

Switch-of value

Switch direction

(see section 6.1)

setting parameters for

switching output 2

hold for >2 s**

display functions

Key sequence

Values shown

displaying parameters

for switching output 1

hold for <2 s*

Switch-on value

Switch-of value

Switch direction

(Values are displayed one after the other.

The display then returns to the measured

value;see section 3.4)

displaying parameters

for switching output 2

hold for <2 s*

Other functions

Key sequence

Process flow

Start manual zero-point

calibration

depress

simultaneously and

hold for >2 s**

The zero-point calibration is performed

automatically. The display then returns

to the measured value.

* hold for <2 s: depress the key(s) until the decimal points on the measured value

display begin to move (see fig. 7 (2))

** hold for > 2 s: depress the key(s) until the “PPP” release code appears (see fig. 7

(3)).

Table 2 User functions for the REG 21 pressure regulator

Instruction Manual REG 21

3.3 Device parameters

Several parameters are available for adapting instrument operation to a number of

different applications. Section 6.1 describes how to set parameters; table 3 provides

an overview of available parameters.

Parameter

Description

basic settings

time constant

the amount of time required for the display, analogue output and (if

the corresponding parameters are set) switching outputs to

respond to changes in pressure

brightness

display brightness

zero-point

calibration

automatic or manual zero-point calibration options

relay output 1

switch-on value

pressure threshold value that activates the switching output, see

section 3.4

switch-off value

pressure threshold value that disables the switching output, see

section 3.4

switch direction

parameter for selecting one of the two possible directions between

the two relay/transistor output states, see section 3.4

switching output 2 (analogous to switching output 1)

switch-on value

see above

switch-off value

see above

switch direction

see above

Table 3 parameters for the REG 21 pressure regulator

Inhaltsverzeichnis

Andere halstrup-walcher Controller Handbücher

halstrup-walcher

halstrup-walcher PSD4 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

halstrup-walcher REG 21 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken