Hamilton Beach HBF500S-230V Handbuch

Technical Data Sheet

PROPRIETARY RIGHTS NOTICE This document and all information contained within it is the property of Hamilton Beach Brands, Inc. (HBB). It is confidential and proprietary

and has been provided to you for a limited purpose. It must be returned or destroyed upon request. Disclosure, reproduction or use of this document and any information

contained within it, in full or in part, for any purpose is forbidden without the prior written consent ofHBB. No photographs may be taken of any article fabricated or assembled

from this document without the prior written consent of HBB.

Revision Description: Production Release

Request Number: DOC2649 Revision Date: 4/17/12 Approved by: DOC2649

4421 Waterfront Drive

Glen Allen, VA 23060 Issue Code(s): CS, SP Page: 1 of 4Document #: 520006200 Rev: A

ENG-FRM-RIC-4.32, Rev. E

HBF500S-230V Food Blender Technical Information

Trouble Shooting Guide

-Symptom: During a normal cycle the machine stopped.

-Cause: The unit has possibly overheated. Check the electric circuit. Check the reset switch. If

both check OK unplug the machine, allow it stand for 15-30 minutes. Plug it back in and try

running the machine.

Repair Guide

Housing Disassembly (see figure 1)

-Turn power switch to “off” position and unplug the machine.

-Remove feet.

-Remove the four screws under the feet.

-Carefully lift bottom from unit; wires will limit your movement.

Figure 1. Machine interior.

Wiring Detail

Cord (see figure 2)

-White cord lead splits with one lead connecting to the PC board terminal N and one lead

connecting to the inside terminal of the circuit breaker switch.

Technical Data Sheet

PROPRIETARY RIGHTS NOTICE This document and all information contained within it is the property of Hamilton Beach Brands, Inc. (HBB). It is confidential and proprietary

and has been provided to you for a limited purpose. It must be returned or destroyed upon request. Disclosure, reproduction or use of this document and any information

contained within it, in full or in part, for any purpose is forbidden without the prior written consent ofHBB. No photographs may be taken of any article fabricated or assembled

from this document without the prior written consent of HBB.

Revision Description: Production Release

Request Number: DOC2649 Revision Date: 4/17/12 Approved by: DOC2649

4421 Waterfront Drive

Glen Allen, VA 23060 Issue Code(s): CS, SP Page: 2 of 4Document #: 520006200 Rev: A

ENG-FRM-RIC-4.32, Rev. E

-Black cord lead connects to the outside terminal of the circuit breaker switch.

-Green cord wire connects to the motor ground.

Figure 2. Cord and circuit breaker switch.

PC Board (see figure 3)

-The motor field lead closest to the PC board connects to terminal M1. There should be no

current reading.

-The motor field lead closest to the RFI board connects to terminal M2. There should be line

current when cycle start is activated.

-One white lead from the cord connects to terminal N. There should be no current reading.

-The black lead from the center terminal of the circuit breaker switch connects to terminal L.

There should be line current present.

-The 4-conductor cable from the LED cycle counter connects to terminal J7.

-The 3-conductor cable from the speed control connects to terminal J8.

-The 2 – 3-conductor cables from the jar sensors connect to terminals IC3 and IC4

-The lead from terminal P1 on the RFI board connects to the P1 terminal on the PC board.

-The lead from terminal P2 on the RFI board connects to the P2 terminal on the PC board.

Note: When making the following connections “top” and “bottom” are relative to the machine assembled

and sitting upright.

-“Off “ terminal lead connects to the top terminal of the on/off switch.

-5 VDC reading with switch in off position.

-“On” terminal lead connects to the center terminal of the on/off switch.

-5 VDC reading while the machine is running.

-“Start” terminal lead connects to bottom terminal of the on/off switch.

Momentary -5 VDC when start switch is activated.

-“Pulse” terminal lead connects to the top terminal of the hi/low/pulse switch.

Technical Data Sheet

PROPRIETARY RIGHTS NOTICE This document and all information contained within it is the property of Hamilton Beach Brands, Inc. (HBB). It is confidential and proprietary

and has been provided to you for a limited purpose. It must be returned or destroyed upon request. Disclosure, reproduction or use of this document and any information

contained within it, in full or in part, for any purpose is forbidden without the prior written consent ofHBB. No photographs may be taken of any article fabricated or assembled

from this document without the prior written consent of HBB.

Revision Description: Production Release

Request Number: DOC2649 Revision Date: 4/17/12 Approved by: DOC2649

4421 Waterfront Drive

Glen Allen, VA 23060 Issue Code(s): CS, SP Page: 3 of 4Document #: 520006200 Rev: A

ENG-FRM-RIC-4.32, Rev. E

-5 VDC when pulse switch is activated.

-“High” terminal lead connects to the bottom terminal of the hi/low/pulse switch.

-5 VDC while running on high speed.

-“Low” lead connects to the center terminal of the hi/low/pulse switch.

-5 VDC while running on high or low speed.

Figure 3. PC Board

RFI Board (see figure 4)

-One white lead from the cord connects to terminal N. There should be no current reading.

-The lead from the center terminal of the circuit breaker connects to terminal L202.

-The lead from the motor ground connects to the GND terminal.

-The lead from terminal P1 on the PC board connects to the P1 terminal on the RFI board.

-The lead from terminal P2 on the PC board connects to the P2 terminal on the RFI board.

Figure 4. RFI Board

Technical Data Sheet

PROPRIETARY RIGHTS NOTICE This document and all information contained within it is the property of Hamilton Beach Brands, Inc. (HBB). It is confidential and proprietary

and has been provided to you for a limited purpose. It must be returned or destroyed upon request. Disclosure, reproduction or use of this document and any information

contained within it, in full or in part, for any purpose is forbidden without the prior written consent ofHBB. No photographs may be taken of any article fabricated or assembled

from this document without the prior written consent of HBB.

Revision Description: Production Release

Request Number: DOC2649 Revision Date: 4/17/12 Approved by: DOC2649

4421 Waterfront Drive

Glen Allen, VA 23060 Issue Code(s): CS, SP Page: 4 of 4Document #: 520006200 Rev: A

ENG-FRM-RIC-4.32, Rev. E

Switches

-Important: The ground harness must be connected to the on/off switch, the hi/low/pulse switch

and the motor ground.

-The switches are keyed to ensure alignment.

-The speed control has a single pin and hole for alignment.

-See PC board wiring instructions for switch wire placement.

Motor Removal and Replacement

-Disassemble housings as described in Housing Disassembly above.

-Remove the two ground screws.

-Disconnect the motor leads from the PC board.

-Remove the four screws securing the motor to the upper housing.

-Lift the motor from the shroud.

-Re-assemble in reverse order.

PC Board and RFI board Removal and Replacement

-Carefully slide a long philips head screwdriver between the board and the housing and remove

the two screws that secure the bracket.

-Lift the PC board or RFI board from the machine and disconnect the wires.

-Re-assemble in reverse order.

How to Determine Cycle Count

-Turn the power switch to the “off” position.

-Unplug the machine.

-Turn the machine upside down and position so that you can look into the three holes on the

bottom/front of the machine.

-Plug the machine into a power source.

-Count and record the number of flashes from the LED lights; first Red, then Yellow, then

Green.

-Once complete add two zeros to the end. This is your cycle count.

-Example: Red – 2, Yellow – 0, Green – 8. You have recorded 208. At the end add two zeros -

20800. Your cycle count is 20,800.

Last revised 2/24/2012

Inhaltsverzeichnis

Andere Hamilton Beach Mixer Handbücher

Hamilton Beach

Hamilton Beach 54226 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 53517 Bedienungsanleitung

Hamilton Beach

Hamilton Beach HBB250 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 53602-CN Bedienungsanleitung

Hamilton Beach

Hamilton Beach 994 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 50163 Betriebsanleitung

Hamilton Beach

Hamilton Beach 58912-CN Bedienungsanleitung

Hamilton Beach

Hamilton Beach 50161N - Wave-Action Blender Bedienungsanleitung

Hamilton Beach

Hamilton Beach 58915-CN Bedienungsanleitung

Hamilton Beach

Hamilton Beach Summit HBH850 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 58146-CL Bedienungsanleitung

Hamilton Beach

Hamilton Beach HMI Series Bedienungsanleitung

Hamilton Beach

Hamilton Beach Blender Bedienungsanleitung

Hamilton Beach

Hamilton Beach 1G901 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 52400-CN Bedienungsanleitung

Hamilton Beach

Hamilton Beach 50233P Bedienungsanleitung

Hamilton Beach

Hamilton Beach Ice Shaver Bedienungsanleitung

Hamilton Beach

Hamilton Beach HBS1200 Bedienungsanleitung

Hamilton Beach

Hamilton Beach 51180 Betriebsanleitung

Hamilton Beach

Hamilton Beach 54616C Bedienungsanleitung

Hamilton Beach

Hamilton Beach 908 Series Bedienungsanleitung

Hamilton Beach

Hamilton Beach SUMMIT BBS0850 Bedienungsanleitung

Hamilton Beach

Hamilton Beach HBH450 Bedienungsanleitung

Hamilton Beach

Hamilton Beach Go Sport Bedienungsanleitung

Beliebte Mixer Handbücher anderer Marken

ROTOR

ROTOR 1125.201 Bedienungsanleitung

Braun

Braun Multiquick 5 Vario series Bedienungsanleitung

ARENDO

ARENDO MIRA 305424 Bedienungsanleitung

CHEF-BUILT

CHEF-BUILT CCB-3500 Bedienungsanleitung

Viconte

Viconte VC-4406 Bedienungsanleitung

Oster

Oster BLSTAB-CB0 Bedienungsanleitung

HOFFEN

HOFFEN MC-3005 Bedienungsanleitung

Sunbeam

Sunbeam 4182 Bedienungsanleitung

Black & Decker

Black & Decker BLC18750DM Bedienungsanleitung

Bialetti

Bialetti FMX35 Bedienungsanleitung

Black & Decker

Black & Decker BL8000 Bedienungsanleitung

Duronic

Duronic BL530 Bedienungsanleitung

Exquisit

Exquisit MS 3002 wes Bedienungsanleitung

Lumme

Lumme LU-KP1891A Bedienungsanleitung

Binatone

Binatone HB-735 Bedienungsanleitung

Moulinex

Moulinex LM936E10 Bedienungsanleitung

Oster

Oster VERSA Installations- und Betriebshandbuch

Ninja

Ninja NN210Q Bedienungsanleitung