Hamilton HTK Bedienungsanleitung

Document #101-0204 1 10/21/2011

HTK

Installation Manual

Document #101-0204 2 10/21/2011

TABLE OF CONTENTS

I. INTRODUCTION ................................................................................................... 4

II. INSTALLATION ................................................................................................... 5

MECHANICAL INSTALLATION ..............................................................................................5

Unpacking............................................................................................................................5

Positioning ...........................................................................................................................6

Mounting..............................................................................................................................6

Running Conduit..................................................................................................................6

HTK Dimensions (For brick-in installation) ............................................................ 7

HTK Dimensions (Free Standing installation) ......................................................... 8

Brick-In Installation.................................................................................................. 9

Free-Standing Installation....................................................................................... 10

Brick-In Installation.................................................................................................11

Free-Standing Installation....................................................................................... 12

Gate Orientation...................................................................................................... 13

Access Control Lane Layout................................................................................... 14

III. ELECTRICAL INSTALLATION...................................................................... 15

Pulling Wires......................................................................................................................15

Wire Terminations .............................................................................................................15

Power Supply Wiring Connection .......................................................................... 17

BRING MAIN POWER INTO OUTLET TO POWER MACHINE ..................... 17

Wash Interface ........................................................................................................ 18

HTK “Automatic” Wiring ...................................................................................... 19

HTK “Gated Tunnel” Wiring.................................................................................. 20

HTK “Ether Vend” Wiring...................................................................................... 21

Additional Wire Terminations For Use With The Credit Card or Customer Value Card

System. ..............................................................................................................................22

Additional Wire Terminations For Use With A Hamilton Code System or POS 4000 .....22

Additional Wire Terminations For Camera In HTK. ........................................................23

Additional Wire Terminations for Help Button in HTK....................................................23

Setting Car Wash Cycle Synchronization .........................................................................24

IV. COMPONENT CONNECTIONS ...................................................................... 25

Power Supply.......................................................................................................... 26

Controller................................................................................................................ 27

Distribution............................................................................................................. 28

Smart Bus Hub........................................................................................................ 29

Bill Dispenser ......................................................................................................... 30

Stacker Interface..................................................................................................... 31

Gate and Loop References...................................................................................... 32

Document #101-0204 3 10/21/2011

PLEASE READ THIS MANUAL CAREFULLY

PRIOR TO INSTALLING THIS UNIT. A complete

understanding of the operation of this unit is

essential for a successful installation.

Refer to the Table of Contents for easy

navigation through this manual.

This manual was designed to introduce the Hamilton Transaction Kiosk and to provide general infor-

mation about installation. This manual will enable the installer to properly install the HTK and make

the proper wire connections to the HTK. To obtain assistance from the manufacturer, please call (800)

837-5561 or (419) 867-4858. Or contact Hamilton Mfg. online @ http:\\www.hamiltonmfg.com.

When calling for assistance, it is important to have serial numbers readily available. Please record these

numbers in the spaces provided.

HTK MODEL & SERIAL #

CONTROLLER MODEL & SERIAL #

HOPPER MODEL & SERIAL #

STACKER MODEL & SERIAL #

VALIDATOR SERIAL #

BILL DISPENSER SERIAL #

LOCK/KEY #

Please complete the warranty card, which was included with your machine, and return it to the manu-

facturer.

ABOUT THIS MANUAL

Document #101-0204 4 10/21/2011

I. Introduction

This manual will describe the installation of the Hamilton Transaction Kisok from a mechanical and

electrical perspective.

Automatic / Rollover

•Brick in Mounting

• Schematic drawing of mounting conﬁguration of HTK

• Schematic drawing of cabinet dimensions

• Schematic drawing of conduit mounting holes

• Schematic of HTK wiring connections

Tunnel / Gated

•Schematic drawing of mounting conﬁguration of HTK

• Schematic drawing of positioning of HTK and Gate

• Schematic drawing of cabinet dimensions

• Schematic drawing of conduit mounting holes

• Schematic drawing of wiring connections for HTK, Gates and Gated

PLC

NOTE: Website links to Gate and Loop information is provided on

page 24.

*IMPORTANT NOTICE: HAMILTON MFG. RECOMMENDS

THAT THE HTK OPERATE ON A DEDICATED POWER

SOURCE. UNDER NO CIRCUMSTANCE SHOULD ADDI-

TIONAL EQUIPMENT BE OPERATING OFF THE DEDICAT-

ED POWER SOURCE FOR THE HTK.

Document #101-0204 5 10/21/2011

II. Installation

NOTE: It is very important to read and understand all of these in-

structions before attempting installation. Hamilton will not be

responsible for injury due to improper installation.

The installation process contains two distinct operations, Mechanical Installation, and Electrical

Installation

MECHANICAL INSTALLATION

 Unpacking

There are a number of points to keep in mind while unpacking your HTK. These items will make the

installation and continued operation of your machine run smoother. These tips are listed below.

Be sure to save your keys

The keys and lock inserts are placed inside a cushioned envelope bag, then placed inside the machine

located next to the power supply. When removing the shrink-wrap, be sure to locate the “T” handle

crank and set it aside so it does not get thrown away. MAKE A PERMANENT RECORD OF THE

NUMBERS ON YOUR KEYS IN CASE A KEY IS LOST AND MUST BE REORDERED.

Remove the packing strap from the hoppers

The hoppers comes shipped with a packing strap secured around it to minimize the vibrations caused

by shipping. If this strap is not removed, the hopper will not tip out for easy ﬁlling. The strap may be

cut off with a pair of wire cutters or sturdy scissors. Cardboard is placed around the edges of the hop-

per to protect it during shipping. After removing the strap, be sure to remove the cardboard as well.

In addition to the removal of the card board and strapping, one of the hoppers will be holding the

paper for the receipt printer.

Remove all packing debris from the hopper

During unpacking, ensure that debris does not fall into the hopper bowl. If this material is not removed,

the hopper could jam. With the power completely disconnected, remove all loose material inside the

hopper bowl.

Remove HTK from shipping pallet

The HTK is securely mounted to the pallet with 4 mounting bolts and nuts. To remove the HTK from

the pallet, open the main door and locate the cushioned envelope to retrieve the key for the vault. Once

you have the vault door open loosen and remove the two nuts from the bolts. Repeat this process on the

two bolts on the side of the power supply. Once this process is complete, you will be able to remove

the HTK from the pallet.

Removal of additional packing materials

Inside the HTK are additional components that have packing material holding the component in place

for secure shipping. The following will need to be removed for proper operation. The ﬁrst is the strap-

ping around the Validator. Another is the removal of the tape around the coin mechanism. In addition

the tape and paper on the front of the bill dispenser, this also incudes the tape that holds the bill rejection

tray. Finally the removal of the tape from the coin box, which need to be placed underneath the coin

mechanism inside the cabinet.

Document #101-0204 6 10/21/2011

Brick Mounted

 The ﬁrst method is to construct a brick or concrete enclosure that will house the HTK. Figure

on page 7 (HTK Bolt Pattern Brick-In) gives the HTK mounting hole locations.The HTK

provides for six 5/8” mounting holes. Have your engineer or contractor recommend con-

struction suitable for strength and stability.

Base Mounted (Free Standing)

 The other method involves mounting the HTK on an optional HTK Base . In this situation,

the base is secured to the pavement and the HTK is secured to the base. Fasteners to be used

should be recommended by your engineer as to strength and suitability.

NOTE: The HTK that mounts to the HTK Base is speciﬁcally

designed to be mounted together. Trying to mount a brick mount

style HTK to the base, is not compatiable.

 Running Conduit

Typical electrical code requires low and high voltage wiring to be run in separate conduits. Because of

this, the HTK has three 1 1/8 “ conduit mounting holes in the back of the cabinet, as well as six 1 1/8”

conduit holes in the bottom of the cabinet.

NOTE: When running your conduit refer to “HTK Bolt Pattern

Brick-In” located on page 7.

 Conduit carrying high voltage 120VAC power lines, should be connected to either one of

the bottom 2 right or 1 back right conduit holes, as viewed from the front of the machine.

These conduits are designated only for 110v for the power supply.

 Conduit carrying lines with 24VAC, 24VDC, 12VAC or 12VDC signals should be connected

to either one of the four bottom left or back 2 left conduit holes, as viewed from the front of

the machine.

 If any external communication lines (Cat 5 or Cat 5E, Video, POS etc.) are used, they should

be run through separate conduit and connected to any of the open conduits on the left bottom

or left back of the machine.

NOTE: In the Free Standing cabinet there will be no conduit holes

in the back.

 Positioning

There are no set guidelines for the placement of the HTK. However, it is recommended that the ma-

chine is positioned far enough away from the wash entrance to minimize the amount of overspray that

may get into the HTK. Also, there is a typical height, from the pavement to the bottom of the cabinet,

of approximately 24”.

 Mounting

It is recommended that the HTK be mounted in a permanent enclosure. Safety is a primary concern, so

the equipment must be securely mounted. Hamilton recommends using one of the following methods:

Document #101-0204 7 10/21/2011

HTK Dimensions (For brick-in installation)

Document #101-0204 8 10/21/2011

HTK Dimensions (Free Standing installation)

Document #101-0204 9 10/21/2011

Brick-In Installation

Document #101-0204 10 10/21/2011

Free-Standing Installation

1 7/8

2 3/4

CURB

Ø1 1/8 CONDUIT HOLES FOR

SIGNAL WIRES AND ETHERNET

Ø1 1/8 CONDUIT HOLES FOR

SIGNAL WIRES AND ETHERNET

1 1/2

7 3/8

Ø1 1/8 CONDUIT HOLE FOR 110V ONLY

Ø5/8 MOUNTING HOLES

( 6 PLCS )

15 7/8

4 1/8

28 3/8

6 1/8

20 1/8 5 1/2

HTK FREE STANDING CABINET BOLT PATTERN

( CUTAWAY VIEW OF BOTTOM OF CABINET)

Andere Handbücher für HTK

Inhaltsverzeichnis

Andere Hamilton Digitale Beschilderung Handbücher

Hamilton

Hamilton HTK Betriebsanleitung

Beliebte Digitale Beschilderung Handbücher anderer Marken

LG 72WS70MS-B Bedienungsanleitung

SMART-AVI

SMART-AVI SIGNAGEPRO Bedienungsanleitung

LG 65SM5D Bedienungsanleitung

LG 55EW5TK-A.AUS Bedienungsanleitung

KeyWest Technology

KeyWest Technology BREEZE Bedienungsanleitung

XtendLan

XtendLan XL-DSP-183C Bedienungsanleitung

LG 47VL10 Bedienungsanleitung

LG WP400 Kurzanleitung

Dynascan

Dynascan DS861LR4 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1363 Bedienungsanleitung

LG 22XE1J Bedienungsanleitung

protech

protech KT-7290 Bedienungsanleitung

WebDT

WebDT 515A Montageanleitung

Samsung

Samsung IWJ Series Bedienungsanleitung

LG 84TR3B Bedienungsanleitung

LG 55EJ5D Kurzanleitung

EVERI

EVERI Enrollment Kiosk Bedienungsanleitung

LG 75XS4G Bedienungsanleitung