Hanshin Smart Thermal Detector Bedienungsanleitung
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 1 / 19
Smart Thermal Detector
User Manual
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 2 / 19
Table of Contents
Table of Contents ...................................................................................................................... 2
Warning and Precaution............................................................................................................ 3
Packaging checklist.................................................................................................................... 3
Hardware Overview................................................................................................................... 4
User Interface Overview............................................................................................................ 5
Temperature Screening Procedure ........................................................................................... 6
Temperature Screening Hints.................................................................................................... 6
Thermal Detector Setting.......................................................................................................... 7
Android-related setting............................................................................................................. 9
CMS Cloud control system ...................................................................................................... 11
HANSHIN thermal: Mobile Application Notification ............................................................... 16
Local Record Exporting............................................................................................................ 19
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 3 / 19
Warning and Precaution
○The operation temperature of Smart Thermal Detector is 10 - 40 ℃(50 –104 °F).
Using this machine in the extreme environment may cause damage to the machine
○When Smart Thermal Detector shows elevated temperature (Yellow or Red), adjust
the position to measure again / use another thermometer to measure the
temperature accurately. If you have other signs of illness, please consult your doctor
immediately
○Smart Thermal Detector is designed to be a rapid screening tool for temperature.
This product is not designed to diagnose any disease or as a substitute for the
consultation of the doctor
○Insert the power adapter fully into the main socket
○Do not touch the power adapter with wet hands
○Do not expose this machine to rain or excessive moisture. This machine must not be
exposed to dripping or splashing water
○Do not expose this machine to direct sunlight and other sources of heat
Packaging checklist
Smart Thermal Detector
Item
Description
Quantity
1
Smart Thermal Detector
1
2
DC12V Power Adapter
1
3
User manual
1
4
Smart Thermal Detector wall mount
1
Optional items
Smart Thermal Detector floor stands
Upon request
Smart Thermal Detector table stands
Upon request
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 4 / 19
Hardware Overview
Front
Top and back side
Front
Back
1
Thermal Detector Sensor
6
DC Power Input
2
Distance Sensor
7
3.5 mm Audio Out
3
Environmental Thermometer
8
Micro-SD Card Slot
4
Optical Sensor
9
USB Port
5
10.2 inch LED display
10
USB Port
6
NFC Sensor
11
RJ45 LAN Port
12
Power on / off button
1
2
6
5
3
6
7
8
9
10
11
4
12
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 5 / 19
User Interface Overview
1
Temperature Detection Standard
2
Temperature Detection Area
3
Local Exporting
4
Date & Time
5
NFC Card information
6
Setting
1
2
3
4
5
6
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 6 / 19
Temperature Screening Procedure
1. Tap NFC card on the NFC Sensor if you would like to record detection with
your detection (if applicable)
2. Move your head towards the Smart Thermal Detector until your face covered
most area of the human-shaped frame of the detection area (around 50 cm
distances between the forehead and the machine). Detection area will show a
scanning animation when the distance is appropriated. If no scanning
animation is shown, move your head closer to the machine. The Screening
will start immediately once the animation is shown
3. Wait for 1 second until the display shows the screening result
4. The display shows below screening result regarding the use of body
temperature
Temperature Screening Hints
To ensure temperature screening result accurate, please avoid below environmental factors:
Factors
Effect
Room Temperature Too High / Low
Deviations will be found in
Measuring results
Obstruction found between the forehead and the
measuring machine
Measure unsuccessfully
Measuring too far
Inaccurate measuring results
32˚C - 37.3˚C
(89.6˚F - 99.1˚F)
Green
Normal Body Temperature
37.4˚C - 38˚C
(99.2˚F - 100.4˚F)
Yellow
Moderate Fever
38.1˚C - 42˚C
(100.5˚F - 107.6˚F)
Red
High Fever
Temperature a bit low
Recommend to take off glasses
and retry
Temperature too low
The measurement may be done
incorrectly / interference found
Please retry
Temperature too low
The measurement may be done
incorrectly / interference found
Please retry
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 7 / 19
Users should avoid measuring temperature in the cases below, wait for 20 minutes before
measuring the temperature.
Situation
Effect
After intense exercise
Measure result will be high
After hot bath
Measure result will be high
After long time exposure to directly sunlight
Measure result will be high
Wearing too many clothes / not enough clothes
Measure result will be high/low
Thermal Detector Setting
Connect USB Mouse to the Smart Thermal Detector for detail settings of the software.
Consult your ITAdministrator before the setting
Click the setting icon by moving the mouse
cursor with your connected mouse.
The configuration page will be shown
immediately.
Basic Setting
1. Capture photo when body temperature
detected exceed 37.3˚C/ 99.1˚F
By enabling this function, a photo will be
captured when abnormal body temperature is
detected (e.g. Yellow and Red)
2. Capture photo when body temperature
detected successfully
By enabling this function, a photo will be
captured after the detection no matter what
the result is
3. Enable smart camera detection
By enabling this function, smart camera can
detect human faces
4. Enable fast detection
1 second fast detection is enabling
5. Enable body temperature measurement after
tagged NFC card
By enabling this function, the measurement
will only start after users tap their NFC card
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 8 / 19
6. Display 24H
Change display of 12H into 24H
7. Display MM/DD/YYYY
Change display of DD/MM/YYYY into
MM/DD/YYYY
8. Display in ˚F(Degree Fahrenheit)
Change display of ˚C into ˚F
Advanced Setting
It is not necessary to set the advanced
configuration in normal usage. Please contact
your local supplier before making any of the
advanced settings.
1. Kiosk –Machine ID
Enter the Machine ID provided by your local
supplier. Make sure the machine is connected
to the internet before activating.
2. Cloud Server Address
Enter the CMS web address to connect to
the cloud platform. This value is usually
pre-configured and not necessary to
configure.
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 9 / 19
Android-related setting
Smart Thermal Detector is running in Android platform. Besides those settings in the smart
thermal detector software, there are some basic settings to be set in Android.
Connecting to Wi-Fi network
Smart Thermal Detector supports connecting to the internet with both Wi-Fi and LAN. Before
using the Smart Thermal Detector, it is required to set the internet settings in the Android
system.
Connect the mouse to Smart Thermal Detector,
right-click the mouse to exit the Smart Thermal
Detector software to go to the Home screen of the
Android system.
Click on the setting to enter the Android settings.
Enter Wi-Fi settings.
Select and enter the required information to
connect to the Wi-Fi network.
Smart Thermal Detector
User Manual V1.5
Smart Thermal Detector User Manual V1.1
Copyright © 2020 Hanshin International Limited
All Rights Reserved Page 10 / 19
Adjust the Sound volume
InAndroid settings, go into the Volume settings.
Adjust the sound volume of the machine. It is not
recommended to adjust to higher than 90%
volume.
Inhaltsverzeichnis
Beliebte Temperaturregler Handbücher anderer Marken
Swegon
Swegon LUNAd MB Bedienungsanleitung
Lucky Reptile
Lucky Reptile Thermo Control II Bedienungsanleitung
SENSORMETRIX
SENSORMETRIX Argon 100 Bedienungsanleitung
Fuji Electric
Fuji Electric PXE4 Bedienungsanleitung
Yuyao gongyi
Yuyao gongyi XMT-808 series Bedienungsanleitung
Selec
Selec TC544C Bedienungsanleitung
