Hansol 730E Bedienungsanleitung



User’s Guide

730E(1772E)

COLOR MONITOR

Regulatory Information.......................................................................................................................... 2

Introduction

Features ...................................................................................................................................................4

Controls

OSD Controls ...........................................................................................................................................5

OSD Menus ..............................................................................................................................................6

Power Management Feature................................................................................................................. 9

Standard Signal Table ............................................................................................................................ 9

Specifications ........................................................................................................................................ 10

Pin assignment table D-Sub Mini 15pin connector .......................................................................11

Troubleshootings .................................................................................................................................. 12

Table of Contents

Color Monitor

Regulatory

Information

- FCC Information

- Declaration of

Conformity

FCC COMPLIANCE STATEMENT :

This device complies with part 15 of FCC Rules. Operation is subject to the following two

conditions : (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

HANSOL MULTITECH, INC.

17785 Center Court Dr. Ste. 665 Cerritos, CA 90703, USA

TEL : 562-809-8005 FAX : 562-809-8015

This equipment has been tested and found to comply with limits for a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause unacceptable interference to radio and television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol-

lowing measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced Radio/TV technician for help.

PRODUCT NAME : 17" COLOR MONITOR

MODEL NUMBER : 1772E

FCC RULES : TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT : FOR HOME OR OFFICE USE

Color Monitor

Caution

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

- Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

- Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

- Energy Star As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star

guidelines for energy efficiency.

Notice

The information contained in this document is subject to change without notice.

Color Monitor

Introduction

- Features

The exclusive double dynamic focus system with a hyperbolic focus compensation circuit controls the electron

beams resulting in a fine image display over the entire area of the screen.

Super contrast screen for superior contrast and richer color.

Advanced INVAR Shadow mask for superior focus, brightness and color.

On screen menu color control system easily allows the white of the image to be adjusted as well as R.G.B

signals, resulting in true-to-life colors.

Ergonomic Design

Flat, square screen to reduce image distortion and glare, thus relieving eye strain.

Low-leak radiation prevention meeting MPR Ⅱand the very stringent TCO magnetic field emissions standards

for increased user safety.

Environmentally Friendly

Power management circuit conforming to VESA DPMS standards controls energy consumption when monitor

is not in use, you save energy.

All plastic parts are recyclable. All materials are strictly selected to ensure ease of maintenance, inspection and

disposal.

Timing

Automatic tracking of horizontal frequencies of 30 to 72 kHz, and vertical frequencise of 50 to 160 Hz.

Eight timings are factory preset for image size and position.

Eight additional timings are user definable.

System Flexibility

Equipped with DDC1, DDC2B and DDC2Bi for Plug & Play compatibility.

Monitor is compatible with VGA, SVGA, VESA and high resolution video modes up to 1280(H) x 1024(V) 60Hz.

Automatic universal power supply is built in permitting AC power input of 100 - 240V AC, 50 or 60Hz.

Self-test menu allows the display unit to be checked on screen without connecting to a computer.

Superior image.

Color Monitor

Controls

- OSD controls

Function of OSD buttons on the front of the monitor

In the main menu, exits the OSD controls. In a submenu, exits to the OSD main menu.

－/ +

1) When no OSD on the Screen.

－: Direct access to Brightness controls.

+ : Direct access to Contract controls.

2) When Main menu is displayed. : Moves to function what you want to adjust.

3) When the Sub menu is displayed. : Controls the amount what you want to adjust.

MENU : Displays OSD main Menu.

1) When Main menu is displayed. : Selects function with RED ICON.

2) When Sub menu is displayed. : Selects function with RED ICON.

Additional front controls

Power Switch : Turns the monitor power on or off. When the power is on, the LED is on.

LED Power indicator Light : Located left side of the power switch and indicates the monitor's power mode.

Each mode reduces the amount of power used by the monitor.

Accessing on screen menu

Press MENU Button.

Turning off on screen menu

When in the main menu, press button.

When in submenus, press the button twice.

"ON SCREEN MENU" controls include the following extended controls such as Size, Position,

Geometry, Color Adjust, Brightness and Contrast Utilities. Adjustments are saved instantly.

The currently addressed control can be reset to factory settings by pressing the Reset button.

Color Monitor

Controls

OSD MENU MENU CONTROL

1. NO OSD Proceeds to NO.2

－Proceeds to NO.3

+ Proceeds to NO.4

No meaning

2. MAIN MENU The function with RED ICON is

- Performed : Recall, Degauss

- Selected and blinked :

Color Adjust, Zoom

- Proceeded : Others

－+ Moves to function you want.

Exit to No.1

3. BRIGHTNESS

Moves to No.2

－Decreases the brightness

+ Increases the brightness

Exit to No.1

4. CONTRAST

Moves to No.2

－Decreases the contrast

+ Increases the contrast

Exit to No.1

5. H/V-POSITION

Toggles horizontal or

vertical position

－Moves the image down or left in the

selected function.

+ Moves the image up or right in the

selected function.

Exit to No.2

6. H/V-SIZE

Toggles horizontal or

vertical size

－Shrinks the image in the selected

function.

+ Expands the image in the selected

function.

Exit to No.2

- OSD Menu

Color Monitor

7. GEOMETRY Odd press

: Selects and blinks the function

with RED ICON.

－+ Controls the amount of the Selected

function. (Refer to Geometry

controls menu in detail)

Exit to No.2

Even press

: Stops blinking and ready to

move function you want.

－+ Moves to function you want.

Exit to No.2

8. MOIRE Odd press

: Selects and blinks the function

with RED ICON.

－+ Controls the Amount of the seleccted

function. Please control these key

inorder the image not to shiver.

Exit to No.2

Even press

: Stops blinking and ready to

move function you want.

－+ Moves to function you want.

9. LANGUAGE

Selects the languages with

RED ICON and Exit to No.2.

－+ Moves to language you want.

Exit to No.2

10. OSD POSITION

Toggles OSD position

horizontally or vertically.

－Moves the OSD menu left or down in

the selected function.

+ Moves the OSD menu right or up

in the selected function.

Exit to No.2

11. COLOR MODE

Odd press

: Blinks the RED ICON

- color menu ICON.

－+ Moves to color mode you want and

the selected “color mode” will blink.

Exit to No.1

Even press

: Stops blinking and ready to

move function you want.

－+ Moves to function you want.

Exit to No.1

When the color mode ICON

isblinking in user mode, press,

then go to color adjust mode

No.12.

－

Color Monitor

12. COLOR ADJUST MODE

RB - Red background raster

GB - Green background raster

BB - Blue background raster

RG - Red level gain

GG - Green level gain

BG - Blue level gain

Odd press

: Selects and blinks the

function you want.

－+ Controls the amount of function

you want.

Exit to No.11

Even press

: Stops blinking and ready to

move function you want.

－+ Moves to function you want.

Exit to No.11

13. ZOOM Odd press

: Selects zoom and blinks the

zoom ICON.

－Shrinks the image horizontally and

vertically.

+ Expands the image horizontally and

vertically.

Exit to No.1

Even press

: Stops blinking and ready to

move another function.

－+ Moves to the function you want.

Exit to No.1

Recall ( )

Recall control to the factory setting resets all the controls within the all menu.

If you want to return to the factory mode setting, press menu key on Recall

ICON.

Degauss( )

Eliminates the build-up of stray magnetic fields which alter the correct scan of

the electron beams and affect the purity of the screen colors, focus, and

convergence. When pressed, you screen image will jump and waver a

bit as the screen is demagnetized.

※Geometry Controls Menu

•Pincushion : Increases or decreases the curvature of the sides either inward or outward.

•Parallelogram : Increases or decreases the tilt of the sides either to the left or right.

•Trapezoid : Increases or decreases the bottom of the screen to be the same as the top.

•Pin Balance : Increases or decreases the curvature of the sides either to the left or right.

•Rotation : Increases or decreases the tilt of the screen image relative to a horizontal line.

Caution : Please allow a minimum of 20 minutes to elapse between

uses of the Degauss button. Do no hold the button down

continuously to avoid decreasing the life the Deguass

circuitry.

The Geometry controls allow you to adjust the curvature or

angle of the sides of you display.

Color Monitor

Power

Management

Feature

The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager

Signalling (DPMS) mode of Video Electronics Standard Association(VESA).

The power management feature requires that the video card of the computer should support DPMS function.

Standard Signal

Table

Status LED Sign Power Consumption

Normal mode Green ON Normal Power

DPMS mode Green Blinking Less than 3 W

Resolution Horizontal

Frequency(kHz)

Vertical

Frequency(Hz)

Clock Frequency

(MHz)

Sync Polarity

(H/V)

VGA (720 x 400) 31.469 70.087 28.322 －/ +

VGA (640 x 480) 31.469 59.940 25.175 －/ －

VGA (640 x 480) 37.500 75.000 31.500 －/ -

VGA (640 x 480) 43.269 85.008 36.000 －/ －

SVGA (800 x 600) 46.875 75.000 49.500 + / +

SVGA (800 x 600) 53.674 85.061 56.250 + / +

XGA (1024 x 768) 60.023 75.029 78.750 + / +

XGA (1024 x 768) 68.677 84.997 94.500 + / +

No image is displayed with Green blinking

Monitor is in power saving mode.

Use mouse or keyboard to release power saving mode.

No image is displayed without LED on.

Power cable plug must be pulled out.

Check the power plug on monitor and on the wall.

"Out of range" displayed on the screen.

This message is displayed when the signal from video card exceeds the maximum

frequency of the monitor. Readjust resolution and frequency in accordance with the monitor

capacity.(Refer to Standard Signal Table).

Color Monitor

Specifications

※ It is different according to option.

ITEM 730E(1772E)

CRT Type 17", 90°deflection FST

CRT Horizontal Dot pitch 0.24mm

CRT Surface Non-glare, Anti-Reflection & Anti-Static

Input

Signal

Sync. H/V Separate, TTL, positive/negative

H/V Composite, TTL, positive/negative

Video RGB Analog (0.7Vp-p), positive

75 Ω Terminated

Scanning

frequency

Horizontal 30KHz~72KHz (Automatically)

Vertical 50Hz~160Hz (Automatically)

Maximum Resolution 1280Dots x 1024Lines (Non-interlace)

Pixel Clock(Max.) 110 MHz

Display Size (Standard) Horizontal 306mm, Vertical 230mm

Power Consumption(Max.) 74 Watts

Power Supply AC 100~240Volt, 60/50Hz ±3Hz

Input Connector D-Sub, 15Pin Connectors

Display Colors Unlimited

Dimension

Unit

(with stand) 15.6" (W) x 16.4" (D) x 16.1"(H) / 397mm(W) x 417mm(D) x 410.2mm(H)

Carton 18.1" (W) x 19" (D) x 17.7"(H) / 461mm(W) x 485mm(D) x 450mm(H)

Weight Net 32.1lbs (14.6kg)

Gross 36.4lbs (16.5kg)

Temperature

Operating 32℉ to 104℉(0℃to 40℃)

Storage -4℉ to 140℉ (-20℃ to 60℃)

Humidity 10% to 85% R.H.Non-condensing

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hansol Monitor Handbücher

Hansol

Hansol 920A Bedienungsanleitung

Hansol

Hansol B19CL Bedienungsanleitung

Hansol

Hansol D17CL Bedienungsanleitung

Hansol

Hansol 520f Bedienungsanleitung

Hansol

Hansol 19Inch (Viewable size 18 ) High Resolution Color Monitor... Bedienungsanleitung

Hansol

Hansol H950 Bedienungsanleitung

Hansol

Hansol H950VI B19BF Bedienungsanleitung

Hansol

Hansol H750D Bedienungsanleitung

Hansol

Hansol 730D Bedienungsanleitung

Hansol

Hansol D19BL Bedienungsanleitung

Hansol

Hansol H750 Bedienungsanleitung

Hansol

Hansol E19AL Bedienungsanleitung

Hansol

Hansol H700TD Bedienungsanleitung

Hansol

Hansol H530 Bedienungsanleitung

Hansol

Hansol D19AL Bedienungsanleitung

Hansol

Hansol B15BF Bedienungsanleitung

Hansol

Hansol D17CL Bedienungsanleitung

Hansol

Hansol 700Fs Bedienungsanleitung

Hansol

Hansol H750D Bedienungsanleitung

Hansol

Hansol H550 Bedienungsanleitung

Hansol

Hansol H550 Bedienungsanleitung

Hansol

Hansol D17DL Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung