Hantek PPS2116A Bedienungsanleitung
CONTENTS
1. INSTRUCTION..........................................................................................................................................................................................................................................1
2. SPECIFICATIONS....................................................................................................................................................................................................................................1
3. USER GUIDE............................................................................................................................................................................................................................................2
4. ATTENTION...............................................................................................................................................................................................................................................7
5. MAINTENANCE........................................................................................................................................................................................................................................7
6. ACCESSORIES........................................................................................................................................................................................................................................8
1. INSTRUCTION
This power s pply are integrated analog and digital control technology in one of the new general-p rpose power s pply, it has both analog power
high stability, low ripple noise characteristics of digital circ its and easy implementation and a variety of control f nctions, for yo r work and prod ction
provides a wide range of convenient, simple, easy-to- se. Specification see Table 1:
Table 1
Type PPS2116A
O tp t Voltage 0-32.00V(step 0.01V)
O tp t C rrent 0-5A
Power
(220VLoaded)
192VA
Weight Abo t 3.6Kg
2. SPECIFICATIONS
2.1 So rce effect: CV≤0.01％+3mV(mA)
2.2 Load reg lation: CV≤0.01％+3mV(I≤3A) CC≤0.2％+3mA(I≤3A)
2
Load reg lation: CV≤0.02％+5mV(I>3A) CC≤0.2％+5mA(I>3A)
2.3 Ripple & Niose: CV≤1.0mVrms(I≤3A) CC≤3mArms(I≤3A)
Ripple & Niose: CV≤2.0mVrms(I>3A) CC≤6mArms(I>3A)
2.4 Protection type: Overc rrent protection (OCP) Overvoltage protection (OVP)
2.5 Show the acc racy: Precision voltage directive,±(0.5％+2 words)
Acc racy of c rrent instr ctions,±(1％+2 words)
2.6 O tp t voltage rise time: Unladen <60ms Loaded:<60ms
2.7 O tp t voltage fall time: Unladen:<100ms Loaded:<100ms
2.8 Working Voltage:220V±10％AC 50Hz/60Hz
2.9 Package Size:310mm×150mm×205mm(L×W×H)
2.10 Dimensions: W (100mm)×H (160mm+ Machine feet 6mm)×D (275mm non-terminal)
2.11 Operating environment:temperat re0～+40 relative h midity≤80℃％
3. USER GUIDE
3.1 Panel Instruction
3.1.1 Front Panel Instr ction
(1) Indicates the o tp t voltage (2) 5 Gro p o tp t parameter storage instr ctions
(3) Indicates the o tp t c rrent (4) Gro p 5 o tp t parameters to store and select
(5) SHIFT key to enable the second f nction (6) O tp t t rn-off b tton
(7) Panel key lock f nction (8) Voltage adj st selection key
(9) C rrent adj st selection key (10) Power ON –OFF control
(11) “+” o tp t terminal (12) “GND” terminal
(13) “-“ o tp t terminal (14) ADJUST switch
(15) Over-c rrent protection instr ctions (16) C rrent stat s instr ctions
(17) O tp t t rn-off instr ctions (18) Overvoltage protection instr ctions
(19) Constant stat s instr ctions
3.1.2 Rear Panel Instr ction
(20) Cooling fan (21) USB interface (Limited to prod cts DPS2000U series)
3
(22) Power s pply socket and f se holder
FIG.1 Front Panel
FIG.2 Rear Panel
3.2 Operation Instruction
4
3.2.1 Front Panel Operation Instruction
Front panel display incl des, Voltage, c rrent digital display, constant voltage, over-voltage stat s, o tp t, constant c rrent, over-c rrent
protection LED stat s of instr ctions. Panel Feat res
M1, M2, M3, M4, M5 Preset storage parameters selection key;
SHIFT is the second f nction enable key;
SHIFT is the second f nction enable key; O tp t t rn-off key can be arbitrarily c t off the o tp t, witho t having to se the power switch;
LOCK Relax all panel key lock to ens re that job witho t external infl ence;
VOL, VUR Voltage / c rrent adj st selection key, one-b tton switch, space-saving;
ADJUST Safe and reliable digital code switch, effective way to avoid the noise Analog potentiometer o tp t more stable, reliable.
3.2.2 Operation Instruction
This series of power s pplies with o tp t parameter storage gro p 5 f nctions in se can be divided into normal se, pre-storage to se
both cases, normal se, Refer to the following steps:
(1). Open the power switch, set the voltage, press the VOL voltage adj st selection key, shows the digital voltage reg lator t be is selected,
the selected digital t be stat s in the flickering, spinning move ADJUST switch, variable voltage val e of the size, again press the VOL
voltage adj st selection keys can be selected to change the location of digital t be;
(2). C rrent settings, press VUR c rrent adj st selection key, shows the digital t be c rrent reg lation is selected, the selected digital t be
stat s in the flickering, spinning move ADJUST switch, set the c rrent val e of variable size, once again press the adj st VUR select key,
adj st voltage selection b tton, the selected digital t be location;
(3). Achieve the voltage and c rrent settings, the time did not press the power b tton o tp t sh tdown, power is t rned off, no o tp t, press
the OUTPUT key to t rn off the o tp t after the stat s instr ction constant (CV), the o tp t stat s ( OUT) of the lantern was lit, power
normal work; see FIG.3:
5
FIG.3 O tp t stat s Fig re FIG.4 Lock stat s Fig re
(4).Over-c rrent close settings, press the SHIFT key, panel indicator led M1～ M5 are lighted, then press the OUTPUT key ,at this point the
power s pply r n in the over-c rrent close mode . When the overload OCP led is lighted and c t off the o tp t voltage.
(5). Panel b tton lock, at the normal o tp t apparat s can se the feat re, which is mainly in order to avoid the load when connected to
adj st the o tp t voltage to the harmf l effects of the load, The se of panel keypad lock is on, press the keyboard key lock (LOCK) 2
second or more, digital display "-Loc", said keyboard panel has been locked, the keyboard is locked, the Operation panel is displayed
when "-Loc" prompt, all keys are not working, nlock long again by the b tton, yo can ret rn to normal stat s, see FIG.4:
Defa lt storage can store a maxim m of 5 gro p o tp t parameter defa lt val e to M1 as an example by doing the Following:
(1). Storage operation, first set the preset voltage, c rrent, specific settings can be when sed with reference to the normal voltage and
c rrent settings methods, voltage and c rrent settings End After, After Press the second f nction enable key (SHIFT) on the panel, M1～
M5LED all lighted, the show voltage and c rrent val es are to be stored, see FIG.5 and see FIG.6;
FIG.5 Storage stat s FIG.6 After storage
stat s
(2). Press the corresponding memory key o tp t parameters, storage time of M1, M1 pressing keys corresponding to the M1 light-emitting
diode light, see FIG.6
(3). Other in each gro p stored in the defa lt method and the same M1;
6
(4). O t has been stored at the defa lt, press the M1 key to display the stored voltage, c rrent, and then press the sh tdown b tton
OUTPUT, can be stored in the o tp t voltage, C rrent, see FIG.7
FIG.7 Memory o tp t
. ATTENTION
4.1 The power s pply feat res over-c rrent protection with so nd, when the o tp t short circ it, the circ it protection will be activated only when
a short circ it when tro bleshooting to restore o tp t.
4.2 Maintenance of power s pply, the inp t power m st be disconnected by repair professionals
4.3 Machine after se, please be ventilated dry place, not long-term, sho ld npl g the power pl g
4.4 Belong to high-power instr ment of the power s pply, at f ll capacity, therefore they sho ld pay attention to the se of ventilation and cooling
power, and power radiator shell and a higher temperat re, please note that hand-to-avoid
4.5 Three core power cord the protective earthing gro nding terminal m st be reliable to ens re that the se of safety
4.6 When the power to place too m ch time re- se, pre-election power 15 – 20 min tes and be stable before eq ipment p t into se
5. MAINTENANCE
The apparat s sho ld be sed nder normal working conditions, are not allowed in the s nlight expos re, a strong vibration and occasions
with the se of corrosive gases.
7
5.1 F se replacement
If the f se b rned, the eq ipment will not be able to work. F se will not open normally, nless the fail re of circ its. Please check before
replacing f ses may ca se b rning f se circ it, and then replace the f se. F se replacement, please se the original specifications in line
with the f se
5.2 Cleaning
When cleaning the instr ment, se ne tral detergent Baptist has a soft cloth and water. Do not spray detergent on the s rface of the
apparat s, there is probably beca se of detergent into the internal chassis damage. Do not se with gasoline, benzene, tol ene, xylene,
acetone and other chemical s bstances or similar solvent. Do not se abrasive cleaning prod cts s ch as the apparat s
6. ACCESSORIES
Prod ct se instr ctions 1
Power cord 1
O tp t Line: 1
Prod ct certification 1
Matching: USB Interface, Comm nication Software
8
Inhaltsverzeichnis
Andere Hantek Stromversorgung Handbücher
Hantek
Hantek PPS 1004A Bedienungsanleitung
Hantek
Hantek HDP10000 Series Bedienungsanleitung
Hantek
Hantek HT3003PB Bedienungsanleitung
Hantek
Hantek HDP135V6 Bedienungsanleitung
Hantek
Hantek HDP4000 Series Bedienungsanleitung
Hantek
Hantek HDP43 Series Bedienungsanleitung
Hantek
Hantek HT3003PE Bedienungsanleitung
