Harbor Freight Tools ZURICH OBD2 Montageanleitung
Visit our website at: http://www.harborfreight.com
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back
of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep
this manual and the receipt in a safe and dry place for future reference. 21j
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2021 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 59091
Table of Contents
Safety ..........................................3
Specifications ..............................5
Overview......................................5
Operating Instructions..................6
Warranty ......................................8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Page 3For technical questions, please call 1-888-866-5797.Item 59091
Important Safety Information
Work Area Safety
1. Keep your work area clean and well lit.
Cluttered benches and dark
areas may cause accidents.
2. Do not connect or disconnect the
Code Reader while the ignition
is on or the engine is running.
3. DO NOT attempt to operate
the Code Reader while driving
the vehicle. Have a passenger
operate the Code Reader.
4. Before testing a vehicle, engage the
parking brake and chock the tires.
5. NEVER smoke or allow a spark or
flame in vicinity of battery or engine.
6. Carbon Monoxide is produced
while the vehicle’s engine is
operating and is deadly in a closed
environment. Early signs of carbon
monoxide poisoning resemble the flu,
with headaches, dizziness, or nausea.
If you have these signs, the work
area may not be vented properly. Get
fresh air immediately. Operate the
vehicle in a well-ventilated work area.
7. Do not operate the Code Reader
in explosive atmospheres, such
as in the presence of flammable
liquids, gases, or heavy dust.
8. Keep a fire extinguisher suitable for
gasoline/chemical/electrical fires nearby.
9. Use extreme caution when working
around the ignition coil, distributor
cap, ignition wires and spark plugs.
These components create hazardous
voltages when the engine is running.
10. Keep bystanders, children and visitors
away while operating the Code Reader.
11. This product is not a toy. Do not allow
children to play with or near this item.
12. Use as intended only.
13. Inspect before every use; do not use
if parts are loose or damaged.
14. Do not place the Code Reader
on any unstable surface.
15. Handle the Code Reader with care. If
the Code Reader is dropped, check
for breakage and any other conditions
that may affect its operation.
16. Keep the Code Reader dry, clean,
free from oil, water or grease.
Use a mild detergent on a clean
cloth to clean the outside of the
Scan Tool, when necessary.
17. Store the Code Reader in a locked
area out of the reach of children.
18. Maintain product labels and
nameplates. These carry
important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Electrical Safety
1. Do not use the Code Reader
while standing in water.
2. Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators.
3. Do not expose the Code Reader to rain
or wet conditions.
Water entering the Code Reader
increases the risk of electric shock.
4. Make sure your hands are dry before
operating the Code Reader.
Page 4 For technical questions, please call 1-888-866-5797. Item 59091
Personal Safety
1. Wear ANSI-approved safety
goggles during use.
2. Do not wear loose clothing or jewelry.
Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
can be caught in moving parts.
3. Do not use the Code Reader while
tired or under the influence of
drugs, alcohol, or medications. A
moment of interruption can result
in serious personal injury.
4. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference
or pacemaker failure.
5. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
Service
There are no user serviceable parts. Code Reader service must
be performed only by qualified repair personnel.
Page 5For technical questions, please call 1-888-866-5797.Item 59091
Specifications
Working Voltage 12 V DC provided by vehicle battery
Overview
OBD II On-Board Diagnostics
It is required by the EPA that all 1996 and
newer vehicles sold in the United States be
equipped with an OBD II computer system.
OBD II is an early warning system
designed to monitor engine, transmission,
and emissions control components by
performing specific diagnostic tests.
When a fault condition is detected, the
system captures important data and
activates the “Check Engine” light.
If the light comes on, the vehicle might have
a condition that wastes fuel, shortens engine
life, or causes excessive air pollution. If
the problem that caused the light to come
on is addressed, for instance a loose gas
cap is tightened, the light will go out.
If the light comes on and stays on, a minor
engine fault condition is occurring and
should be addressed as soon as possible
If the light is blinking, a severe engine
fault condition is occurring and should
be addressed immediately.
The Code Reader connects to the vehicle’s
computer system and captures information
that can help identify the fault condition.
Page 6 For technical questions, please call 1-888-866-5797. Item 59091
Operation
1. Scan QR code for iOS,
Repair Solutions 2 App.
2. Scan QR code for Android,
Repair Solutions 2 App.
3. Download and open
Repair Solutions 2 App.
4. Type in Email Address, create
and confirm Password.
5. 16-pin DLC is usually located under
dashboard, within 12 inches of
center of panel, on driver’s side
of most vehicles. Check vehicle’s
service manual for exact location.
BEHIND
ASHTRAY
NEAR
CENTER
OF DASH
LEFT CORNER
OF DASH
6. Connect Bluetooth Code Reader to
vehicle’s Data Link Connector (DLC).
Data Link
Connector
(DLC)
Bluetooth
Code
Reader
7. Turn ignition key to “Acc.”.
DO NOT start engine.
8. Press here and follow prompts.
Page 7For technical questions, please call 1-888-866-5797.Item 59091
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175454454 when ordering parts.
FCC ID - 2AMWOFC-BT825
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Andere Handbücher für ZURICH OBD2
1
Andere Harbor Freight Tools Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
