Hargrove H-Tube Betriebsanleitung

Installation and service must be provided by a qualified installer,

service a

enc

or the

as su

lier.

ADEQUATE FIREPLACE VENTILATION IS REQUIRED FOR SAFETY

READ INSTRUCTIONS FULLY BEFORE INSTALLING OR OPERATING

INSTALLER: LEAVE THESE INSTRUCTIONS WITH CONSUMER!

NOTE:

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WARNING: If the information in this

manual is not followed exactly, a fire or

explosion may result causing property

damage, personal injury or loss of life.

It is the homeowner’s responsibility to

assure their fireplace has adequate draft.

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS

1. Do not try to light any appliance.

2. Do not touch any electrical switch; do

not use the phone in your building.

3. Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions.

4. If you cannot reach your gas supplier,

call the fire department.

INSTALLATION AND OPERATION GUIDE FOR

HARGROVE

Glass H-Tube and

Stainless Steel “S” Burner

The gas appliance must be burned only in a fully vented, non-combustible fireplace with the damper

completely open and the chimney free of any obstructions or restrictions. The fireplace must be designed and

approved to burn wood.

The realistic yellow flame produces carbon monoxide and soot. Under normal conditions, these products are

exhausted up the chimney. If fumes or soot, from the gas burning, are evident in the room when the damper is

fully open it indicates that the fireplace draft is defective. Do not operate your gas appliance until the fireplace

draft is corrected.

IMPORTANT INFORMATION

WARNING: This appliance assembly contains burner orifices specifically for the input gas and

Btu rating. Modifying or failure to use the factory orifice may cause property damage, personal

injury or loss of life.

1. Do not use a natural gas set for propane or a propane set for natural gas.

2. There a many different local codes for gas appliances. The installation and the provision for combustion and

ventilation air must conform to local codes and, or in the absence of local codes, with the National Fuel Gas Code

ANSI Z223.1 – (most current revision).

3. Gas appliances must be installed by personnel qualified for installing gas appliances.

4. This appliance must be installed only in a solid-fuel burning fireplace with a working flue and constructed of

noncombustible materials. Solid fuels are not to be burned in a fireplace where a decorative appliance has been

installed.

5. A permanent free opening must be provided by either the fireplace chimney or chimney damper to vent flue gasses.

Any chimney damper must be fixed in a manner, which will maintain the permanent free opening at all times. Use

Table II to determine the minimum permanent free opening based on chimney height and the appliance Btu input

rating. Refer to the Damper Stop section for additional directions.

6. The minimum free opening is based only on two factors; chimney height and Btu input rating. Many other factors affect

the fireplace drafting. It is the homeowner’s responsibility to assure their fireplace has adequate draft. If fumes or soot

from the gas burning are evident in the room when the damper is fully open, it indicates that the fireplace draft is

defective. Do not operate your gas appliance until the fireplace draft is corrected. Consult your fireplace specialist.

7. A fireplace screen must be in place when the appliance is operating and, unless other provisions for combustion air are

provided, the screen shall have an opening(s) for introduction of combustion air.

8. When glass fireplace doors are used, always operate your gas appliance with the doors fully open to allow for proper

combustion air and to keep control valves from overheating.

9. The minimum inlet supply pressure for the purpose of input adjustment is 5.0 inches (natural gas) 11 inches (propane

gas) in water column. The maximum inlet supply pressure is 10.5 inches (natural gas) 13 inches (propane gas) in

water column.

10. The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5kPa). The appliance must be isolated from

the gas supply piping system by closing its individual manual valve during pressure testing equal to or less than 1/2

psig (3.5kPa).

11. The fireplace chimney or venting system should be examined annually and cleaned as required by a qualified agency.

FIREPLACE SIZES

Front Width

Center Width

Back Width

TABLE I

Minimum Minimum Front Minimum Minimum

Set Size Center Width Opening Width Depth Height

21 28” 30” 16” 16”

24 32” 36” 16” 16”

30 37” 42” 16” 16”

29 39 51 64

Appliance Input Rating, Btu Per Hour (w)

Chimney

Height,

Feet

6 34,000 46,400 62,400 80,000

8 37,000 50,400 68,000 86,000

10 40,400 55,800 74,400 96,400

15 44,600 62,400 84,000 108,800

25 50,400 68,400 94,000 122,200

30 55,200 76,800 105,800 138,600

Each gas appliance requires a minimum 16-inch front opening height and minimum 16-inch depth. To

determine the largest set that will fit in a fireplace, the width at the center of the fireplace is the critical

dimension. Table I below indicates the minimum center width for each size set.

*View is looking down on the fireplace floor. To determine center width, add front width and

back width and divide by 2.

TABLE II

Free opening area of chimney damper for venting combustion products from decorative

appliances for installation in vented fireplaces. Minimum size of chimney flue is 8” diameter.

Minimum Permanent Free Opening, Square Inches

INSTALLING GLASS H-TUBE

PARTS LIST

ITEM DESCRIPTION

1. H-Tube

2. Sand

3. Flex connector

4. Brass reducing union

5. Brass reducing elbow

6. Volcanic cinders (3/8”)

7. Damper stop

18SNHT0A0 24SNHT0A0 30SNHT0A0 36SNHT0A0

SSHB18 SSHB24 SSHB30 SSHB36

SD SD SD SD

FCNW-18 FCNW-18 FCNW-18 FCNW-18

46-6-8 46-6-8 46-6-8 46-6-8

50-6-8 50-6-8 50-6-8 50-6-8

VC VC VC VC

DS DS DS DS

NATURAL GAS AND MATCH LIGHT ONLY

1. Make sure gas is shut off.

2. Connect the 1/2” to 3/8” brass reducing elbow (5) to your gas supply.

3. Connect the black flex connector (3) to the elbow (5).

4. Connect the 1/2" to 3/8” brass reducer (4) to the H-tube (1).

5. Make sure that the H-tube has the holes facing down. This will keep

the sand from obstructing the holes. This will not affect flame height.

6. Finally, connect the flex connector (3) to the brass reducer (4). GAS SUPPLY

INSTALLING STAINLESS STEEL “S” BURNER

PARTS LIST FOR NATURAL GAS WITH NO VALVE

ITEM DESCRIPTION

1. S-Burner

2. Black pipe cap

3. Sand

4. Flex connector

5. Brass reducing elbow

6. Brass reducing union

7. Volcanic cinders (3/8”)

8. Damper stop

18SNSB0A0 24SNSB0A0 30SNSB0A0

SSSB18 SSB24 SSB30

CAP-8 CAP-8 CAP-8

SD SD SD

FCNW-18 FCNW-18 FCNW-18

50-6-8 50-6-8 50-6-8

46-6-8 46-6-8 46-6-8

VC VC VC

DS DS DS

5. 6. 7. 8.

1. Make sure gas is shut off.

2. Connect black pipe cap (2) to the side of the burner you are not running gas to.

3. Connect either the brass reducing elbow (5) or brass reducing union (6) to the

side of the burner that is not capped.

4. Connect the other brass reducer to your gas supply.

5. Use the flex connector (4) to connect the two reducers.

6. Finally, make sure that all of your connections are tight before lighting.

18SNSB1B0 24SNSB1B0 30SNSB1B0

SSSB18 SSSB24 SSSB30

CAP-8 CAP-8 CAP-8

CPC-C CPC-C CPC-C

SPC-K SPC-K SPC-K

RSTPB-18 RSTPB-18 RSTPB-18

SD SD SD

FCNW-18 FCNW-18 FCNW-18

50-6-8 50-6-8 50-6-8

46-6-8 46-6-8 463-6-8

VC VC VC

DS DS DS

INSTALLING STAINLESS STEEL “S” BURNER

PARTS LIST FOR NATURAL GAS WITH VALVE

ITEM DESCRIPTION

1. S-Burner

2. Black pipe cap

3. Valve

4. Control knob

5. Thermocouple and pilot

6. Sand

7. Flex connector

8. Brass reducing elbow

9. Brass reducing union

10. Volcanic cinders (3/8”)

11. Damper stop

2. 3.

5. 8.

11.

6. 10.

1. Make sure gas is shut off.

2. Connect either the brass reducing elbow (8) or brass reducing union (9) to your

gas supply.

3. Connect the flex connector (7) from your brass reducer to the nipple on the back

side of your valve.

4. Finally, make sure that all of your connections are tight before lighting.

INSTALLING STAINLESS STEEL “S” BURNER

PARTS LIST FOR LIQUID PROPANE WITH VALVE

ITEM DESCRIPTION

1. S-Burner

2. Black pipe cap

3. Valve

4. Control knob

5. Thermocouple and pilot

6. Air mixer

7. Flex connector

8. Brass reducing union

9. Volcanic cinders (3/8”)

10. Damper stop

18SNSB1B0 24SNSB1B0 30SNSB1B0

SSSB18 SSSB24 SSSB30

CAP-8 CAP-8 CAP-8

CPC-C CPC-C CPC-C

SPC-K SPC-K SPC-K

RSTPB-18LP RSTPB-18LP RSTPB-18LP

AM-55 AM-55 AM-55

FCNW-18 FCNW-18 FCNW-18

46-6-8 46-6-8 46-6-8

VC VC VC

DS DS DS

10.

1. Make sure gas is shut off.

2. Connect brass reducing union (8) to your gas supply.

3. Connect the flex connector (7) from your brass reducing union (8) to the nipple on the

back side of your valve.

4. Finally, make sure that all of your connections are tight before lighting.

CAUTION

THE DAMPER MUST BE FULLY OPEN WHEN

OPERATING THE GAS APPLIANCE! Fig 1

Fireplace

Floor

4” Minimum

Fireplace

Floor

DAMPER STOP

Attach the damper stop clamp to the fireplace damper blade.

Position the clamp to prevent full closure of the fireplace

damper blade. See Figure 1

If the damper stop provided does not fit, the installer shall

install a permanent damper stop that will keep the damper

open to a minimum of opening as determined in Table II.

GLASS H-TUBE POSITIONING

1. Turn the gas off.

2. Remove old log lighter, ashes, and all other

materials from the firebox.

3. Center the Burner on the fireplace floor with the

burner pipe completely visible from the front.

For best results, the Glass H-tube should be

directly under the flue opening with a minimum

of 4” from the front edge of the Glass H-tube to

the fireplace opening. See Figure 2

STAINLESS “S” BURNER POSITIONING

1. Turn the gas off.

2. Remove old log lighter, ashes, and all other

materials from the firebox.

3. Center the Burner on the fireplace floor with the

burner pipe completely visible from the front.

For best results, the Glass H-tube should be

directly under the flue opening with a minimum

of 4” from the front edge of the Glass H-tube to

the fireplace opening. See Figure 3

GAS CONNECTION

1. The gas supply line should be 1/2" Inside Diameter (ID) up to 30 feet and 3/4" for longer distance.

2. Use the gas connector (FCNW-18) to connect gas supply to the H-tube burner and “S” burner.

3. Read lighting instructions. Light pilot on the “S” burner and check for leaks using soapy water. These

controls are factory preset and will not normally require additional adjustment of the pilot flame. If field

adjustment of the pilot flame is required, remove the pilot adjust cover screw to expose the adjusting

screw. Turn the adjusting screw clockwise.

Burner

Fig 2

Burner

Fig 3

Do not use this appliance if any part has been underwater. Immediately call a qualified service

technician to inspect the appliance and to replace any part of the system or gas control, which has

been underwater. Keep this appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

Pilot Flame

Thermocouple

RSTPB-18

BURNER PAN MEDIA (Fig 4)

1. Cover the Glass H-tube with Sand. The Glass

H-tube should be completely covered.

2. Light the gas and observe the flame for even

distribution.

3. The glass or beads are placed over the sand.

Place as much as desired over the area still

allowing the gas comes through.

BURNER PAN MEDIA (Fig 5)

1. Fill the S-burner pan with Sand for NG and

use only glass or beads only for LP. Sand

level should be sloped evenly with the sides of

the S burner should be completely full.

2. Light the gas and observe the flame for even

distribution.

3. The glass or beads are placed over the sand or

directly on the pan for LP. Place as much as

desired over the area still allowing the gas to

come through.

PILOT FLAME (Fig 6)

The pilot light should be checked periodically

to assure proper flame. On the S-burner

pans, the flame should be hanging on the

side, directly over the middle burner. When

turning the main burner on, the pilot flame

should ignite the main gas within 4 seconds

without creating a big poof, depending on the

gas pressure.

VOLCANIC CINDERS

The black volcanic cinders are used to cover the fireplace floor, fitting and tubing around the burner

system. Although not functional, the black cinders act as a picture frame around the glass or beads.

FOR YOUR SAFETY

Fig 4

Sand

Fig 5

Glass or Beads

Fig 6

Sand

Glass or Beads

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causin

ert

dama

ersonal in

or loss of life.

A. This appliance has a pilot, which must

be lit by hand. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some

gas is heavier than air and will settle on

the floor.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try to light any appliance.

2. Do not touch any electric switch; do not

use any phone in your building.

3. Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions.

4. If you cannot reach your gas supplier,

call the fire department.

C. Use only your hand to push in or

turn the gas control knob. Never

use tools. If the knob will not

push in or turn by hand, do not try

to repair it. Call a qualified

service technician.

D. Do not use this appliance if any

part has been under water.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any gas

control, which has been

underwater.

LIGHTING INSTRUCTIONS

GAS OUTLET

GAS INLET

Pilot Adjustment

Screw

Pilot Gas

Supply

4. Find pilot – follow metal tube from the gas control

behind the burner pan.

Pilot Burner

Thermocouple

1. STOP! Read the safety information above on

this label.

2. Push in gas control knob slightly and turn

clockwise to “OFF”.

CONTROL

KNOB

NOTE: Knob cannot be turned from “PILOT” to

“OFF” unless knob is pushed in slightly. Do not

force.

3. Wait five (5) minutes to clear out any gas. If you

then smell gas, STOP! Follow “B” in the safety

information above. If you don’t smell gas, go to

next step.

5. Turn knob on gas control counter-clockwise to

“PILOT”.

6. Push in control knob all the way and hold in.

Immediately light the pilot with a match.

Continue to hold the control knob in for about one

minute after the pilot is lit. Release knob and i

will pop back up. Pilot should remain lit. If it

goes out, repeat steps 3 – 7.

* If knob does not pop up when released, stop and

immediately call your service technician or gas

supplier.

* If the pilot will not stay lit after several tries, turn

the gas control knob to “OFF” and call you

service technician or gas supplier.

7. Turn gas control knob counterclockwise to “0N”.

LIGHTING INSTRUCTIONS

1. Turn knob clockwise from “ON” position to the “PILOT” position. Push in the gas control knob slightly

and turn clockwise to “OFF”. Do not force knob.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hargrove Brenner Handbücher

Hargrove

Hargrove Firepit Burners Betriebsanleitung

Beliebte Brenner Handbücher anderer Marken

Riello

Riello RS 28/M Kurzanleitung

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Riello

Riello RX 500 S/PV Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

AESYS

AESYS TurboFire II Bedienungsanleitung

Riello

Riello RG1RKD Kurzanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch

Riello Burners

Riello Burners P 200 P/G Kurzanleitung

WLD-TEC

WLD-TEC powerjet Bedienungsanleitung