Harvest TEC 239DM Bedienungsanleitung

239DM - 20

5/21

OWNER’S MANUAL

Model 239DM

Dye Sprayer Marking System

Accessory upgrade to CNH DIA Moisture kits 439618, 48189657, & 90420182

Forage Harvester

Harvest Tec 739DM Table of Contents

Page

Introduction & Tools Needed

Installation of Dye Sprayer Tank & Plumbing

System Wiring

Installation of Plumbing

5-7

Plumbing Diagram

Plumbing Troubleshooting

Baler Display Integration

8-18

Case LB334/434 & New Holland Big Baler Series

(MY2020 and Prior)

Case LB436HD & MY2021 and later LB4 Series

New Holland 340/1290HD & MY2021 & later Big Baler Series

8-14

15-18

Display Options

Operation of Tablets

Operating the Harvest Tec 700 Series System

Filling Tank & Start Up

Operation Instructions Automatic or Manual Mode

20-23

24-31

Pin Outs

33-36

Parts Breakdown

Warranty

Introduction

Congratulations on purchasing a Harvest Tec Dye Sprayer Marking System. When attached to a DIA star

wheel moisture sensor for Case/New Holland large square balers the 239DM allows you to visibly mark the wet

areas on your bales. The system includes the tank, pump, plumbing, mounting hardware and necessary

harnesses. There is a parts breakdown in the back of the manual to reference if replacement parts are needed.

All replacement parts and dye will be ordered through your local CNH dealer.

Tools Needed

Standard wrench set

Hammer

Straight edge

Standard socket set

Tape measure

Metal drilling and cutting tools

Center punch

Marker

Installation of Dye Sprayer Tank & Plumbing

Installation of Mounting Bracket & Tank –CASE & New Holland Large Squares

Locate the tank and mounting bracket assembly. Looking at Figure 1 decide where a desirable mounting

location will be the most convenient and work the best for the user.

a. Once tank location is decided, mark the mounting holes and drill  bit.

b. 

System Wiring

Setting up Tractor

1. Connect the red and black eye-loop connectors from 006-765IC Tractor Power/Communication harness

DIRECT to tractor battery. Route 18 pin plug to drawbar of tractor and the other leg of the harness with the 12

Pin and 4 Pin connector into the cab of the tractor.

2. 006-6673 ISO Communication Module (ICM) mounts in the cab of the tractor and connect 006-765IC 12 pin

header harness to it.

3. Connect 006-765CPH key power harness to 4 pin plug on 006-765IC harness near ICM. Securely fasten to

key power outlet in cab of tractor

4. Secure wires with zip ties.

Setting up baler.

1. Route 006-765BN harness from draw bar of baler back toward Balers ECU

2. Remove 006-7303CMS star wheel harness plug from Baler ECU CAN 2 connection and attach 006-765BN

to same connection of 006-7303CMS harness.

3. Remove 006-4640J resistor plug from the 006-7303CMS harness and attach 006-

765VN to same connection of 006-7303CMS. Reattach 006-4640J to port on 006-765VN.

4. Locate the CAN Port 1 on the baler ECU. Remove 6 pin active terminator (X504) from

CAN 1 (Figure 2) and attach active terminator to 006-765VN harness 6 pin plug

5. Attach 006-765VN harness to Baler ECU CAN 1 plug

Setting up Dye Marker

1. Locate the wiring harness (006-765IDM3) supplied in the 239 dye Sprayer Marking Kit.

Connect to triangle plug on the metal frame of the dye marker.

2. Route Dye Marking harness (006-765IDM3) to main star wheel harness (006-7303CMS) and attach it to

triangle CAN plug found near star wheels. Secure with zip ties

Figure 1

Common New Holland and CASE IH baler

mounting position

Figure 2

System Wiring Diagram

 



 



 





 





 



 



 

 





 



 

   

 









Installation of Plumbing

To most effectively mark the wet spots in any bale, Harvest Tec recommends that the nozzles are

mounted directly above or below the Star Wheels. To get the best spray pattern focused directly on

the wet spot of the bale the nozzles will need to be approximately above the bale that is being

marked. A small notch may need to be cut to increase surface area of the bale being marked.

1. Once you have the tank and mounting bracket securely fastened to the baler, locate parts A, B,

C, D & E pictured below in Figure 2. Assemble in the following order: (A) Elbow | (B) nozzle

holder | (C) check valve | (D) reducing bushing | (E) tip as pictured below.

*****Note: All parts should be thread taped*****

2. Once the nozzle holders are fastened to the balers, route the 3/ to the tips. Make sure to

fasten the hose securely but avoid pinching the lines. (Plumbing Diagram pictured in Figure 3)

*****Keep from routing the hose in the way of moving parts on the baler*****

3. Attach drain hose top hose barb fitting at bottom of tank. Run hose to a secure point and attach

valve assembly.

Check Valve

004-1207V

Elbow

003-SE14F

Brass Tip

004-TX-5

Straight Fitting

003-A1418

Quick Connect

004-1207H

Rubber Gasket

004-1207W

Tip Screen

004-1203-100

Nozzle Holder

001-4216

Nozzle Body

004-4722

Nozzle Cap

004-4723

Figure 2

Installation of Plumbing (continued)

4. Install the tip and nozzle holder assemblies in the suggested locations pictured shown below.



a. Make sure that the tip assemblies (A) are mounted in line with the star wheels (B) so that

the system is marking the wet spots of the bale.

Example A

Example B

Installation of Plumbing (continued)

Plumbing Diagram

Common Question

1. Is the marking dye safe for livestock consumption?

The Dye Marker uses red-colored, food-grade dye and is safe for all livestock.

2. How do I bleed the air out of the lines properly?



the dye marker until the air is pushed out of the lines.

Troubleshooting

Problem

Possible Cause

Solution

The tips are not spraying Dye

1. The system is out of dye.

2. There is air in the lines,

preventing a steady mist

coming from the tips.

3. Damaged/pinched hose.

4. Tip is plugged.

5. Set point is set too high

1. Check the tank for solution. If the tank

is empty, refill and bleed air from lines.

2. Remove the tips from the check valves

and using the priming button bleed the

air out of the lines.

3. Inspect all the hose making sure the

lines are damaged or pinched.

4. Removed the tip from the bushing and

inspect, clean is necessary.

5. Lower the set point level at which the

user would like to have the bales

marked at.

Tank

005-9019

Pump

007-4120LF



002-9003AS

Hose Barb Tee

003-T3838

Brass Tip

004-TX-5

Drain Valve

002-2216

Figure 3

Baler Display Integration

Case LB334/434 & New Holland Big Baler Series (MY2020 and Prior) (continued)

The ISOBUS Monitor utilizes touch screen options to make selections. Selections are made by finding the

desired selection and pressing the touch screen icon. All buttons are labeled and color coded.

When the moisture system is connected thru the baler CAN1 and powered on the first time it is necessary to

load the object pools to the Virtual Terminal (VT).

Case LB334/434 & New Holland Big Baler Series (MY2020 and Prior) (continued)

Icon (1) indicates that the object pools are in the process of loading and saving to the VT. Note that if the

language selection of the VT is changed, the corresponding object pool must be reloaded to the VT. The

object pool loading process takes approximately two minutes to complete.

Once the object pools have been loaded and Icon (1) disappears from the upper left corner of the display,

press the NEXT IMPLEMENT button (2) and verify that the moisture system object pool appear on the Virtual

Terminal.

After verifying that the moisture system object pool is loaded and the operating screens are displayed on the

VT, press the NEXT IMPLEMENT button (3) to return to the baler work screen page.

Press the bottom button of the Menu Bar with the down arrow in corner (4) on the side of the screen to

continue down the Menu Bar below the USER SETTING icon.

Case LB334/434 & New Holland Big Baler Series (MY2020 and Prior) (continued)

Scroll through the Menu bar until the INFORMATION icon (5) is visible. Press the INFORMATION button so

the Information page appears. Verify that the controller software loaded to the baler is version 4.2.0.0 or

higher. If not, contact the dealer to update firmware in Baler Control Module (BCM). If the controller software

displays version 4.2.0.0 or higher proceed to configuring the baler for the moisture system by pressing the

MACHINE SETUP button (6).

Once the MACHINE SETUP icon has been selected, the Machine Setup page will appear, and the icon will be

backlit in orange. Press the MACHINE SETUP icon (7) again to go to the second page of the Machine Setup.

The second page of the Machine setup is identified by the three gray buttons in the Menu Bar. Press and

hold the third gray button (8) for 10 seconds or until the display switches to displaying Dealer Mode.

4.2.0.0

Inhaltsverzeichnis

Andere Harvest TEC Spritzpistole Handbücher

Harvest TEC

Harvest TEC 675 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung