Harvia XENIO CX45J Bedienungsanleitung

04052022/Y05-0917

HARVIA XENIO CX45J

Control unit

These instructions for installation and use are

intended for owners of saunas, heaters and control

units, persons in charge of managing saunas,

heaters and control units, and for electricians

responsible for installing heaters and control units.

Once the control unit is installed, these instructions

of installation and use are handed over to the owner

of the sauna, heater and control unit, or to the

person in charge of maintaining them.

CONTROL UNIT HARVIA XENIO (CX170)

Control unit's purpose of use: the control unit is

meant for controlling the functions of a sauna

heater. It is not to be used for any other purpose.

Congratulations on making an excellent choice!

CONTENTS

1. HARVIA XENIO ........................................................... 3

1.1. General .............................................................. 3

1.2. Technical Data.................................................... 4

1.3. Troubleshooting .................................................. 4

2. INSTRUCTIONS FOR USE............................................. 5

2.1. Using the Heater ................................................. 5

2.1.1. Heater On .................................................. 5

2.1.2. Heater Off.................................................. 5

2.2. Changing the Settings.......................................... 5

2.3. Using Accessories ............................................... 5

2.3.1. Lighting ..................................................... 5

2.3.2. Ventilation ................................................. 5

2.3.3. Safety switch ............................................. 5

2.4. Control panel lock ............................................... 8

2.5. Remote control ................................................... 8

2.6. Power saving mode ............................................. 8

3. INSTRUCTIONS FOR INSTALLATION ............................. 9

3.1. Installing the Control Panel ................................... 9

3.2. Installing the Power Unit .................................... 10

3.2.1. Electrical Connections .............................. 10

3.2.2. Power Unit Fuse Faults .............................. 10

3.2.3. Power extension unit LTY17 (optional) ........ 10

3.3. Installing the Temperature Sensor ....................... 13

3.3.1. Installing the Temperature Sensor WX232 ..... 13

3.4. Resetting the Overheat Protector......................... 13

4. SPARE PARTS .......................................................... 14

1. HARVIA XENIO

1.1. General

The purpose of Harvia Xenio control unit is to con-

trol an electric sauna heater within an output range

of 2.3–18 kW. The control unit consists of a con-

trol panel, a power unit and a temperature sensor.

See figure 1.

The control unit regulates the temperature in the

sauna room based on information given by the sen-

sor. The temperature sensor and the overheat protec-

tor are located in the temperature sensor box. The

temperature is sensed by an NTC thermistor and the

overheat protector can be reset ( 3.4.).

Figure 1. System components

Temperature sensor WX232

Heater

Control panel

Power unit

Sauna room

Safety switch

Dry area

Main switch

Data cable

The control unit can be equipped with a safety

switch (see figure 1). The control unit can be used

to preset the start of the heater (pre-setting time).

See figure 3a.

Sauna room

Dry area

Temperature sensor WX232

Control panel

Heater

Power unit

Main switch

Data cable

Description/Beschreibung Remedy/Abhilfe

E1 Temperature sensor's measuring

circuit broken.

Check the red and yellow wires to the temperature sensor and their

connections (see figure 6) for faults.

E2 Temperature sensor's measuring

circuit short-circuited.

Check the red and yellow wires to the temperature sensor and their

connections (see figure 6) for faults.

E3 Overheat protector's measuring

circuit broken.

Press the overheat protector's reset button ( 3.4.).

Check the blue and white wires to the temperature sensor and their

connections (see figure 6) for faults.

E9 Connection failure in the system. Switch the power off from the main switch (figure 1). Check the data

cable, sensor cable and their connections. Switch the power on.

1.2. Technical Data

Control panel:

• Temperature adjustment range: 40–110 °C.

• On-time adjustment range: family saunas

1–6 h, public saunas in apartment buildings

1–12 h. For longer operating times consult the

importer/manufacturer.

• Pre-setting time adjustment range: 0–12 h.

• Control of lighting and fan

• Dimensions: 85 mm x 24 mm x 110 mm

• Length of data cable: 5 m (10 m extension

cables available, max. total length 30 m)

Power unit:

Supply voltage and max. loads:

• 50/60Hz

• 200 V 1-Phase, Max load 9 kW

• 200 V 1-Phase (two separated circuits) Max

load 18 kW

• 200 V 3-Phase, Max load 15,5 kW

• Max. load can be increased up to 36 kW with a

power extension unit LTY45J

• Lighting control, max. power: 100 W, 200 V 1N~

• Fan control, max. power: 100 W, 200 V 1N~

• Dimensions: 364 mm x 73 mm x 267 mm

• Terminal for a safety switch

Sensors:

Table 1. Error and status messages. Note! All service operations must be done by professional

maintenance personnel.

STATUS MESSAGES / ZUSTANDSMELDUNGEN

SAFE Safety switch circuit is open Remove the object from atop the safety switch

rESt Pause time active -

rc on Remote control activated -

• The temperature sensor is equipped with

a resettable overheat protector and a

temperature-sensing NTC thermistor (22 kΩ/

T=25 °C).

• Weight: 175 g with leads (ca 4 m)

• Dimensions: 51 mm x 73 mm x 27 mm

1.3. Troubleshooting

If an error occurs, the heater power will cut off and

the control panel will show an error message ”E

(number)”, which helps troubleshooting the cause

for the error. Table 1.

Note! All service operations must be done by pro-

fessional maintenance personnel. No user-service-

able parts inside.

2. INSTRUCTIONS FOR USE

Indicator lights

Menu and navigation buttons

Operating buttons

Display

Temperature

On-time

Value decrease *)

Mode change

Value increase *)

Heater on/off

Lighting on/off

Fan on/off

*) Press and hold to make the

value change faster.

Figure 2. Control panel

2.1. Using the Heater

When the control unit is connected to the pow-

er supply and the main switch (see figure 1) is

switched on, the control unit is in standby mode

and ready for use. I/O button’s background light

glows on the control panel.

WARNING! Before switching the heater on always

check that there isn’t anything on top of the heater

or inside the given safety distance.

2.1.1. Heater On

Start the heater by pressing the heater

I/O button on the control panel.

When the heater starts, the top row of the display

will show the set temperature and the bottom row

will show the set on time for five seconds.

When the desired temperature has been reached

in the sauna room, the heating elements are

automatically turned off. To maintain the desired

temperature, the control unit will automatically turn

the heating elements on and off in periods.

If the heater efficiency is suitable and the sauna

has been built correctly, the sauna takes no more

than an hour to warm up.

2.1.2. Heater Off

The heater turns off and the control unit switches

to standby-mode when

• the I/O button is pressed

• the on-time runs out or

• an error occurs.

NOTE! It is essential to check that the control unit

has cut off power from the heater after the on-time

has elapsed, the dehumidification has ended or the

heater has been switched off manually.

2.2. Changing the Settings

The settings menu structure and changing the

settings is shown in figures 3a and 3b.

The programmed temperature value and all values

of additional settings are stored in memory and will

also apply when the device is switched on next

time.

2.3. Using Accessories

Lighting and ventilation can be started and shut

down separately from other functions. Figure 6.

2.3.1. Lighting

The lighting of the sauna room can be wired so that

it can be controlled from the control panel. (Max

100 W.)

Switch the lights on/off by pressing the

control panel button.

2.3.2. Ventilation

If there is a fan installed in the sauna room, it can

be connected to the control unit and be controlled

from the control panel.

Start/stop the fan by pressing the control

panel button.

2.3.3. Safety switch

Safety switch refers to e.g. Harvia SFE, a safety

device installed above or integrated to the heater,

preventing the heater from heating should any

object (e.g. towel, piece of clothing) drop or be

placed on top of the heater and cause a fire hazard.

The safety switch is connected to the control unit

according to its manual. See also figure 6.

Figure 3a. Settings menu structure, basic settings

Press the MENU button to open the settings menu.

Sauna room temperature

The display shows the sauna room temperature setting. Temperature indicator light blinks.

• Change the setting to the desired temperature with the – and + buttons. The range is

40–110 ºC.

Press the MENU button to access the next setting.

Remaining on-time

Press the + and – buttons to adjust the remaining on-time.

Pre-setting time (timed switch-on)

• Press the + button until you overstep the maximum on-time. Temperature indicator light

switches off. Pre-setting time symbol blinks on the screen.

• Select the desired pre-setting time using the – and + buttons. The time changes in 10

minute steps.

Press the MENU button to exit.

Basic mode (heater on)

The top row shows the sauna room temperature. The bottom row shows the remaining on-time.

Both indicator lights glow.

Basic mode (pre-setting time running, heater off)

The decrease of remaining pre-setting time is shown until zero appears, after which the heater is

switched on.

BASIC SETTINGS/GRUNDEINSTELLUNGEN

Example: the heater will be on for 3 hours and 40

minutes.

Example: the heater will start after 10 minutes.

Open the settings menu by simultaneously pressing the locations of the buttons –, MENU

and + (see figure 2). Press for 5 seconds.

The buttons do not glow when the control unit is in standby mode.

Setting the remote use

The remote use setting can be changed with the — and + buttons. The options are "OFF"

(remote control disabled), "SAFE" (safety switch).

See section 2.3.3. for further information.

Confirm the selection with the MENU button.

Setting pause time. Enable or disable the pause time feature with buttons + and -. Pause

time must be enabled, if the control unit is remotely started by an automated schedule

(e.g. a weekly timer).

Press the MENU button to access the next setting.

Maximum on-time

The maximum on-time can be changed with the – and + buttons. The range is 1–12 hours

(6 hours*)).

Press the MENU button to access the next setting.

Sensor reading adjustment

The reading can be corrected by +/- 10 units. The adjustment does not affect the meas-

ured temperature value directly, but changes the measuring curve.

Press the MENU button to access the next setting.

Memory for power failures

The memory for power failures can be turned ON or OFF *).

• When turned on, the system will start again after a break in electricity.

• When turned off, the break will shut the system down. I/O button must be pressed to

restart.

• The safety regulations for memory usage vary from region to region.

Control unit standby

I/O button’s background light glows on the control panel.

ADDITIONAL SETTINGS/WEITERE EINSTELLUNGEN

Example: the heater will be on for 6 hours from the start.

(Remaining on-time can be changed, see figure 3a.)

*) Factory setting

Press the MENU button to access the next setting.

Sauna dehumidifying interval

The sauna dehumidifying interval can be turned ON or OFF*). The interval will begin when

the devices are switched off from the I/O buttons or when the set on-time runs out. During

the interval

• the heater is on

• the sauna room temperature is set at 40 °C.

• If a fan is connected to the control unit, it will also be on.

The length of the interval is 45 minutes. When the time runs out, the devices turn off

automatically. The interval can also be stopped manually at any time by pressing the I/O

button. Dehumidifying helps to keep your sauna in a good condition.

Press the MENU button. The control unit switches to standby-mode.

*) Factory setting

Figure 3b. Settings menu structure, additional settings

Sauna

dehumidifying

in progress

2.4. Control panel lock

Press and hold the heater and

light buttons for three seconds.

-CL- is shown on the display.

Panel lock can be activated only

in standby mode. Panel lock also

prevents remote start.

2.5. Remote control

According to the product standard IEC/EN 60335

-2-53 regulating electrical sauna heaters, a control

unit can be used to remotely control the heater

once the heater is equipped with a secure switch

(safety switch).

Using with a safety switch: the heater can be

turned on remotely, if the safety switch circuit is

closed. If the circuit is open, "SAFE" is displayed

and the heater will not start.

Pause time: These features are limited by a pau-

se time that prevents the heater from turning on

if it has been less than 6 hours since the heater

was last turned off. Trying to remotely turn the

heater on during the pause time period (6 hours),

text ”rESt” is displayed. The heater can be remotely

started after the pause time has elapsed and ”rc”

is displayed.

Memory for power failures: the control unit resu-

mes operation, if the remote switch has remained

in ON position.

Preset time: if the control unit is on preset delay

time, it cannot be controlled with a remote switch.

After the preset delay has passed and the heater

is turned on, it can be turned off with a remote

switch.

Dehumidifying: when the heater is turned off re-

motely and dehumidifying is enabled, dehumidify-

ing starts and cannot be stopped remotely. When

dehumidifying is in progress and a safety switch

is used, the heater can be turned on remotely. If a

door switch is used, the heater cannot be remotely

started, as the remote use mode must be re-activat-

ed by pressing and holding the control unit's heater

button for three seconds.

2.6. Power saving mode

If no buttons are pressed in 30 minutes, power

saving mode is activated. Only the heater button

(and "rc on", if remote use mode is active) is lit.

3,5 x 15 mm

67 mm

96 mm

3,5 x 15 mm

3. INSTRUCTIONS FOR INSTALLATION

The electrical connections of the control unit

may only be made by an authorised, professional

electrician and in accordance with the current

regulations. When the installation of the control unit

is complete, the person in charge of the installation

must pass on to the user the instructions for

installation and use that come with the control unit

and must give the user the necessary training for

using the heater and the control unit.

3.1. Installing the Control Panel

The control panel is splashproof and has a small

operating voltage. The panel can be installed in the

1. Thread the data cable through the hole in the back cover.

2. Fasten the back cover to a wall with screws.

3. Push the data cable to the connector.

4. Press the front cover into the back cover.

Figure 4. Fastening the control panel

washing or dressing room, or in the living quarters.

If the panel is installed in the sauna room, it must

be at the minimum 500 mm safety distance from

the heater and at a maximum height of one metre

from the floor. Figure 4.

Conductor tubing (ø 30 mm) inside the wall struc-

ture allows you to thread the data cable hidden

within the wall – otherwise the installation will have

to be on the wall surface. We recommend you to

install the control panel embedded in to the wall and

far away from possible splashes.

3.2. Installing the Power Unit

Install the power unit to a wall outside the sauna

room, in a dry place with an ambient temperature

of >0 ºC. See figure 5 for instructions on how to

open the power unit cover and how to fix the unit

to the wall.

Note! Do not embed the power unit into the wall,

since this may cause excessive heating of the in-

ternal components of the unit and lead to damage.

See figure 5.

3.2.1. Electrical Connections

Figure 6 shows the electrical connections of

the power unit. For more detailed installation

instructions see the instructions for installation and

use of the selected heater model.

Figure 5. Opening the power unit cover and mounting the unit to a wall

3.2.2. Power Unit Fuse Faults

Replace a blown fuse by a new one with the same

value. The placement of the fuses in the power unit

is shown in figure 6.

• If the fuse F2 for the electronic card has

blown, there is likely a fault in the power unit.

Service is required.

• If the fuse in the line F1, F3 has blown, there

is a problem with lighting or fan. Check the

wiring and functioning of lighting and fan.

3.2.3. Power extension unit LTY45J (optional)

The maximum load of control unit can be increased

by 18 kW by using power extension unit LTY45J.

It is controlled using terminals A1, A2, A3 and A4.

The power extension unit includes detailed instruc-

tions of installation.

Inhaltsverzeichnis

Andere Harvia Steuereinheit Handbücher

Harvia

Harvia C260 Bedienungsanleitung

Harvia

Harvia XENIO CX170 Bedienungsanleitung

Harvia

Harvia C400VKK Bedienungsanleitung

Harvia

Harvia Sentiotec A2 Bedienungsanleitung

Harvia

Harvia griffin Bedienungsanleitung

Harvia

Harvia XAFIR COMBI Bedienungsanleitung

Harvia

Harvia sentiotec home.com4 Bedienungsanleitung

Harvia

Harvia CG170T Bedienungsanleitung

Harvia

Harvia sentiotec home.com4 Bedienungsanleitung

Harvia

Harvia sentiotec Pro C2 Bedienungsanleitung

Harvia

Harvia XENIO COMBI CX30C-U1 Bedienungsanleitung

Harvia

Harvia Pro D IP65 Betriebsanleitung

Harvia

Harvia griffin Bedienungsanleitung

Harvia

Harvia CS10.5 Bedienungsanleitung

Harvia

Harvia GRIFFIN INFRA Bedienungsanleitung

Harvia

Harvia C80/1 Bedienungsanleitung

Harvia

Harvia XENIO COMBI Bedienungsanleitung

Harvia

Harvia XENIO COMBI Bedienungsanleitung

Harvia

Harvia CX170-U1 Betriebsanleitung

Harvia

Harvia CF9 Bedienungsanleitung

Harvia

Harvia CX30C-U1-XW Bedienungsanleitung

Harvia

Harvia C150VKK Bedienungsanleitung

Harvia

Harvia CG170T Leitfaden

Harvia

Harvia XENIO INFRA Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung