HATO 180C Bedienungsanleitung

HATO 180C / 200C

GARAGE DOOR OPERATOR

USER’S MANUAL

OUTLINE

1. Safety instructions………………………………3

2. Main features …………………………………4

3. Technical specifications ………………………5

4. Check …………………………………………5

5. Installation and adjustment ……………………6

6. Programming …………………………………10

7. External terminal connections…………………16

8. Maintenance …………………………………17

9. Troubleshooting ………………………………17

INSTALLATION MANUAL

Our compliments for your excellent choice. The HATO 180C/200C electro-mechanical gear

motor has been produced for reliability and high quality.

This Manual will offer information you may need to install your gear motor assuring long-lasting

performance and to safeguard your safety. HOWEVER CAUTION IS UNQUESTIONABLY

INDISPENSABLE AND NOTHING IS BETTER THAN PREVENTING ACCIDENTS.

CONFORMITY DECLARATION:

It’s in accordance with Machine Directive 2006/42/WE and following modify.

It’s in accordance with the following directive CE:

Electromagnetic compatibility Directive 2014/30/UE and following modify.

Low tension Directive 2014/35/UE and following modify.

Radio directive RED 2014/53/UE

Have been applied the following harmonized norms:

EN ISO 12100:2012; EN 60204-1:2010; EN 60335-2-95:2015, EN 301 489-3 V1.4.1:2006; UNI

EN 12453:2002, where applicable EN 12445:2002

Current declaration are available on website

1.Safety instructions

Carefully read and follow all safety precaution, warnings before attempting to install and use

this garage door operator, incorrect installation can lead to severe injury.

The installation should be carried out by a qualified technician.

To avoid electrical shock, disconnect the power cord from the mains power outlet before

doing any repairs or removing the cover.

The door operator must be grounded.

Before installation of the door operator, the door should be carefully checked for being

kept well balance. The door must be in good working order. Open and close the door

manually, make sure the door can be moved smoothly.

No one or vehicle is allowed to enter or leave the garage while the remoter is being

installed, do not allow children to play near the door.

Locate any fixed control: within sight of door but away from all moving parts of the door

and at a height of more than 1.5m above the ground to avoid children reaching it.

Keep remote controls away from children, to prevent the door operator from being

activated involuntarily.

When opening or closing the door, do not attempt to walk or drive through the door.

The door should only be operated when it can be observed to avoid accidents.

Install and adjust the manual release so that the handle hangs less than 1.5m above the

floor.

Our company reserves the right to change the design and specification without prior

notification.

During the installation and the use of the automation, pay attention to the following safety

rules:

Distance security!

Mechanisms moving!

Do not install automation in an environment saturated with explosive mixtures!

Electric Shock!

Use gloves!

Use welding glasses!

Maintain ear protection!

Failure to comply with the instructions above may result in personal injury or property damage.

Our company does not accept responsibility for damage or injury resulting from installing this

operator.

2. Main features

The door operator is designed for garage door.

The control unit regulates all the necessary functions such as automatic lighting control,

automatic memory, automatic close, automatic reverse and photocell protection etc.,

extremely quiet and smooth operation.

Courtesy light will turns on in using and turns off after 3 minutes.

The operator memorizes the limit positions and unique braking system that slows the unit

down at the end of its travel. Soft start and soft stop control guarantees extremely smooth

and quiet operation.

Automatic reversion on obstruction during closing procedure.

The controller has a security LOCK function which prevents operation of the door from

transmitter.

In the event of power failure, the release device makes it possible to open and close the

door manually.

Hopping code remote control with max. 20 pcs hand transmitters.

Wiring terminals for battery, button switch, infrared photocell etc.

3. Technical specifications

Tools required

A ladder and Tape measure

Electric drill and assorted drill bits

Screwdriver

Spanner / Wrench

Multimeter / Test pen

Hacksaw / Cutter

Pliers / Hammer

Use a helper if possible to assist with the installation.

4. Check

After receiving the product, you should make an unpack-inspection, in which you should check

whether the product was damaged. If you have any problem please contact dealer.

Fig.1

Model

HATO 180C

HATO 200C

Motor power

80 W

100 W

Lifting capacity

800 N

1000 N

Max. door size

8 m2

12 m2

Power supply

220X(1±10%)V AC 50-60Hz

Motor

24VDC

Ambient temperature

-20ºC~+50ºC

Working humidity

≦90%

Courtesy light time

3 minutes

Radio frequency

433.92 MHz

Transmitter type

Rolling code

Transmitter battery

27A 12V

Bulb

24V 5W

1.Powerhead (x1) 3. Shuttle&Manual release cord(x1)

2. Chain drive rail assembly (x1)

6. Door bracket (x1)

5. Header bracket (x1) 8. Straight arm (x1)

10. Screw / Screw cap / Pin and R pin

11. Transmitter (x2)

R pin

Screw(M8x16mm) Screw cap(M8) Screw cap(M6)

7. L arm (x1)

Screw(M6x22mm) Screw(M8x55mm)

4. Powerhead

bracket (x3)

9. Angle iron (x1)

5. Installation and adjustment

Step1

Check the door is in good working condition, manually open and close the door to make

sure the door operates smoothly and freely.

The door must be well balanced.

Check to see if there is a solid frame in the wall above the center of the door.

Close the door.

Measure the door width, mark the centerline of the door using a pencil, and extend the

line down to the door surface, then up the wall above the door.

Check the installation height of the operator. Slowly open garage door and observe the

highest point of door while moving. Close the door again and mark this highest point on

the wall, mark a horizontal line across the vertical centerline around 40mm above the

highest point. (Note: there should be 80mm space between this horizontal line to the

ceiling. If there is not enough space, please use the max. height possible to allow the

header bracket to be fitted properly. )

Garage door

40mm

Fig.2

Tilt door

Sectional door

Highest point

Fig.3

Fit the header bracket to the wall above the door, the centerline of the door should align

with the centerline of the bracket, The bottom edge of the bracket should align with the

horizontal line. Fix the header bracket to the wall with expansion bolts.

Hightest point of

garage door

Horizontal line

Centerline

40mm

Header bracket

Fig.4

Step 2

Insert the shuttle into the groove of the chain drive rail. Be sure it faces the right direction

(the release arm on the shuttle towards the powerhead). Fasten the four screws

(M6x22mm).

Straight arm

Pin and R pin (x1) M6x22mm Screw (x4)

The release arm

towards the powerhead.

Fig.5

Step 3

Place the powerhead on the floor, add cardboard packing to protect the powerhead from

scratching by the floor. Attach the powerhead unit to the chain drive rail, make sure the

spindle is inserted into the chain drive, then fix the brackets.

Steel rail

Powerhead bracket

Powerhead unit

Angle iron

M8X16mm screw (x2)

M8 screw cap(x2)

M6 screw cap(x4)

Mounting bracket (Not included in accessories)

M6X22mm screw (x2)

M6 screw cap(x2)

Fig.6

Step 4

Close the door.

Place the operator in the center of the floor. Lift the front end of the rail up to the header

bracket that has been mounted above the garage door, insert the bolt and secure it with

nut see Fig.7.

Header bracket

Bolt and nut

M8 Expansion bolt (Not

included in accessories)

Fig.7

Step 5

Raise and support the powerhead with a ladder and line up the rail with the centerline

marked on the door. The rail must be level.

Fix the rail to ceiling with mounting brackets (not included in accessories) and angle iron

see Fig.6, make sure that the rail is level. If necessary, Check the door does not touch any

part of the rail by opening or closing it manually.

Fig.8

Step 6

Fix the door bracket on the top edge of the door with screws (M8X55) and screw caps (M8).

Link the L arm to the door bracket with pin and R pin. Link the straight arm to the shuttle with

pin and R pin, then connect L arm to straight arm with two screws (M8X16) and screw caps

(M8), ensure the door arm can be moved freely. See Fig.8, Fig.9 and Fig.10.

L arm

Door bracket

Pin and R pin(X1)

M8 screw cap(X2)

M8x55 screw(X2) M8 Screw cap(X2)

M8X16mm Screw(X2)

Fig.9

Straight arm

Shuttle

L arm

Door bracket

Fig.10

Manual operation

If the door has to be operated manually due to a power cut or malfunction of the automated

system, pull the release rope, open and close the door manually. To reconnect the door, move

the door by hand until it engages into the chain shuttle.

6. Programming

SET button: Mode set and Confirm function

CODE button: Transmitter code set and clear function

UP button: Up limit

DOWN button: Down limit

Fig.11

With power on, the bulb will turn on about 2 seconds and then turn off. The LED will

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HATO Garagentoröffner Handbücher

HATO

HATO 120 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung