Haug EN SL LC Bedienungsanleitung

Keep for future use!

Operating instructions

Power Pack

EN SL / EN SL LC / EN SL RLC

Static Line

Table of contents

1Operator instructions........................................................................ 5

2Safety ................................................................................................. 6

3Intended use...................................................................................... 8

4Description of unit............................................................................. 9

5Installation ....................................................................................... 10

6Application....................................................................................... 14

7Troubleshooting .............................................................................. 15

7.1 Replacing fuse ............................................................................................ 16

7.2 Flow chart.................................................................................................... 17

8Accessories ..................................................................................... 18

9Technical data ................................................................................. 20

9.1 Characteristics and specification................................................................ 20

9.2 Supply voltage ............................................................................................ 21

9.3 Ambient conditions ..................................................................................... 22

9.4 Connected lengths...................................................................................... 23

9.5 Housing ....................................................................................................... 24

10 Decommissioning ........................................................................... 25

11 Disposal ........................................................................................... 26

Types and order numbers

EN SL without thermal cutout:

01.7780.200, 01.7780.208, 01.7780.220, 01.7781.200, 01.7781.208, 01.7781.220

EN SL with thermal cutout:

01.7830.000, 01.7831.000

EN SL LC with thermal cutout and signalling lamp:

01.7833.000, 01.7833.050, 01.7834.000, 01.7834.050

EN SL RLC with thermal cutout, signalling lamp and signalling socket:

01.7835.100, 01.7835.150, 01.7836.100, 01.7836.150

1 Operator instructions

1Operator

instructions

These operator instructions must be

read completely before installation and

commissioning of the power pack.

They form a part of the power pack

and must be retained for later use or

subsequent owners.

Safety instructions must be observed

and followed at all times.

The power pack is operationally safe,

provided that it is operated in

accordance with its intended use.

The power pack is maintenance-free.

The following signal words are

used:

WARNING!

If ignored

severe personal injury.

or death may result.

ATTENTION!

If ignored

light property damage with

damage to the power pack may

result.

NOTE: Important notes and additional

information.

2 Safety

2Safety

All activities must be performed only

by persons authorized by the owner.

Such persons must

be qualified in electrical

engineering.

have read and understood the

operator instructions.

Switch off the power supply before

commencing work on the power pack,

and secure against inadvertent

switching on.

With the exception of the fuse, the

power pack does not include any parts

which can be repaired by the operator.

For reasons of safety, unauthorized

conversions and modifications of the

power pack are not permitted.

Any damage to the power pack may

result in the risk of electric shocks. In

the event of any visible damage or

suspected electrical defects, take the

power pack out of operation

immediately and secure against reuse.

WARNING!

Risk of electric shock.

High electric voltage in power pack.

Risk of electric shock when touching

live parts within power pack.

Do not open the power pack.

2 Safety

ATTENTION!

Risk of short circuit.

Spark-overs and leakage paths at the

high-voltage terminals can occur as a

result of moisture and wetness.

Short circuits within the power pack

are the likely consequence.

Protect the power pack from

wetness and moisture.

Close unused high-voltage

terminals with the red blind plugs.

Risk of spark-over.

When the power pack is switched on,

contact or separation spark-overs may

occur when the ionizing unit is

plugged in or unplugged at the high-

voltage socket.

This may result in damage to the

power pack or defects.

Only plug in/unplug the ionizing

unit at the high-voltage socket

when the power pack is switched

off.

3 Intended use

3Intended use

The power pack is intended

exclusively for the supply of alternating

high voltage to HAUG ionizing units

with X - 2000 connector.

Only HAUG ionizing units with X - 2000

connectors must be connected with

the power pack and operated.

The warranty only covers units and

accessories of HAUG

GmbH & Co. KG.

The installation and operating

conditions indicated in these

Operating Instructions must be

adhered to.

WARNING!

Risk of explosion!

Ignitable sparks may form at the

power pack.

Do not install or use the power

pack in areas subject to

explosion hazards.

4 Description of unit

4Description of unit

1) Mains switch

Green light in switch

illuminates when power pack

is on.

2) Signalling socket (RLC types only)

3) Ground connection (terminal)

4) Signalling lamp (LC and RLC

types only)

5) Bracket

6) High-voltage terminals

7) Mains supply

8) Fuse holder with fuse (for

replacement, refer to page 16,

Chapter 7.1).

5 Installation

5Installation

Do not place the power pack on a

surface generating or radiating heat.

Avoid installation location exposed to

direct sunlight.

1. Check the model plate of the power

pack against the ordering data.

In the event of damage to the power

pack, contact HAUG

GmbH & Co. KG.

2. Before connecting, check to ensure

that the power pack is suitable for

the local mains voltage.

The voltage is indicated on the

model plate attached at the side

of the power pack.

An incorrect mains voltage may

result in damage to the power

pack.

3. Use the enclosed bracket to install

the power pack at the desired

location.

The operation of the power pack

is not affected by the position in

which it is installed.

We recommend installing the

power pack with the high-voltage

terminals pointing downwards

(to protect them from moisture,

oil and dirt).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Haug Power Pack Handbücher

Haug

Haug Multistat S Bedienungsanleitung

Haug

Haug METTLER TOLEDO EN Series Bedienungsanleitung

Haug

Haug 01.7835.300 Bedienungsanleitung

Haug

Haug EN SL SLC MT Bedienungsanleitung

Haug

Haug Static Line EN SL Bedienungsanleitung

Haug

Haug EN SL MT Series Bedienungsanleitung

Haug

Haug EN 8 LC Bedienungsanleitung

Haug

Haug EN 8 SLC MT Bedienungsanleitung

Haug

Haug EN 15 Ex Bedienungsanleitung

Haug

Haug Multistat Ex SDN Bedienungsanleitung

Beliebte Power Pack Handbücher anderer Marken

EcoFlow

EcoFlow Wave 2 Bedienungsanleitung

Schumacher

Schumacher DSR PRO Series Bedienungsanleitung

Draper

Draper 12V Power Packs Bedienungsanleitung

Intermatic

Intermatic IOS-PP24 Kurzanleitung

Makita

Makita PDC01 Bedienungsanleitung

Skiva

Skiva AC110 Bedienungsanleitung

Bluetti

Bluetti AC60P Bedienungsanleitung

Draper

Draper PP12VA Bedienungsanleitung

Goodsmann

Goodsmann 9920-0300-01 Bedienungsanleitung

Risen

Risen RSN-BX007 Bedienungsanleitung

Hama

Hama A4 Series Bedienungsanleitung

Graco

Graco GH 24X011 Stücklistenhandbuch

ring

ring TradeStart RPPS3000 Bedienungsanleitung

Bluetti

Bluetti AC500 Bedienungsanleitung

Hama

Hama 00187292 Bedienungsanleitung

HYCON

HYCON HPP09 Gebrauchsanweisung

Tycon Power Systems

Tycon Power Systems TP-PP120-INV Bedienungsanleitung

Celestron

Celestron PowerTank 17 18777 Bedienungsanleitung