Haws 9001EXPC1D1 Leitfaden

08/17 Model 9001EXPC1D1 Page 1 of 7

No. 2077071(11)

1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424

E-mail: haws@hawsco.com  website: www.hawsco.com

Model 9001EXPC1D1 Alarm

INSTALLATION, OPERATION

MAINTENANCE INSTRUCTIONS

LIMITED WARRANTY

HAWS warrants that this specific product is guaranteed against defective material or poor

workmanship for a period of one year from date of shipment. HAWS liability under this

warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,

or part thereof, which shall appear to the Company upon inspection to be of defective

material or not of first class workmanship, provided that claim is made in writing to Haws

within a reasonable period after receipt of the product. Where claims for defects are made,

the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS

will not be liable for the cost of repairs, alterations or replacements, or for any expense

connected therewith made by the owner or his agents, except upon written authority from

HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective

materials or poor workmanship, except for replacements, as provided above. Buyer agrees

that Haws has made no other warranties either expressed or implied in addition to those

above stated, except that of title with respect to any of the products or equipment sold

hereunder and that HAWS shall not be liable for general, special, or consequential

damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation

and maintenance instructions provided are adhered to. The units also must be used for the

purpose for which they were intended. This product is intended to supplement first-aid

treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this

emergency equipment will prevent serious injury or the aggravation of existing or prior

injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED

OR GIVEN BY HAWS.

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS

MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

FOR CUSTOMER SERVICE: 1-888-640-4297

08/17 Model 9001EXPC1D1 Page 2 of 7

TROUBLESHOOTING

PROBLEM

REPAIR CHECKLIST

Alarm horn and lamp do not

operate.

1a.

Check incoming circuit for power and power

from flow switch.

Check that the direction of water flow

corresponds to the arrow on the flow switch

body.

Check that water flow is sufficient.

Check all electrical connections for security,

including those in alarm base.

Faulty flow switch. Replace entire switch

assembly.

Faulty flasher module in alarm. Replace

flasher module.

Horn sounds but lamp does not

flash.

2a.

Only replace lamp with Haws P/N

0003225505. (See Sheet 3 of Installation

drawing)

Should replacement lamp also fail to operate,

replace flasher module.

Lamp replacement.

3a.

Remove the guard/globe assembly from the

light fixture to replace the lamp. Only replace

lamp with Haws P/N 0003225505. (See Sheet

3 of Installation drawing)

Alarm stays on.

4a.

Check wiring connections.

Disconnect flow switch wires and test for

continuity.

RECOMMENDED TOOLS: Pipe joint sealant, screwdriver, pipe wrench, 14 AWG wire,

3/4” conduit and basic electricians’ tools for power connection.

LOCATION OF UNIT: The Model 9001EXPC1D1 Alarm may be mounted directly to the

upper stand pipe of a safety shower or wall mounted next to a shower or eyewash. The

alarm should be clearly visible from several directions.

ELECTRICAL SUPPLY: 120 VAC 50/60 HZ, 23 Watts average power consumption.

Suitable for use in Class I, Division 1, Group C, D areas; Temperature rating T4 (135°C).

WARNING: Power shall be supplied by a dedicated circuit through a 10 AMP maximum

breaker or fuse and should not supply any power to any other devices.

WATER SUPPLY: The flow switch requires a minimum of 2.4 GPM to activate. Mount

flow switch in supply line with flow in horizontal direction and switch stem extending

vertically from tee. Mount switch with at least 6” of straight pipe on both sides to minimize

turbulence in switch.

08/17 Model 9001EXPC1D1 Page 3 of 7

INSTALLATION PROCEDURE

*WARNING: EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY

IMPAIR SUITABILITY FOR CLASS 1, DIVISION 1.

STEP 1: Choose a location for mounting the flow switch in the water supply line. The inlet

and outlet ports of the flow switch must be a minimum of 6 inches from any tees

or elbows in the water supply line. See attached installation drawing.

STEP 2: Mount the flow switch assembly in the water supply line. The switch body must

be in the vertical position with the water pipe horizontal. The water flow must be

in the direction marked by the arrow on the flow switch body. Use pipe sealing

compound on all water pipe connections.

STEP 3: Choose a location for mounting the alarm assembly. The alarm housing should

be positioned along a vertical axis at least 7 feet above ground for best visibility.

The alarm may be mounted directly to a water pipe using the supplied brackets.

The alarm can also be bolted to a flat surface such as a wall, using flanges with

appropriate fasteners (not supplied).

STEP 4: Using wire nuts, connect the flow switch to the alarm and power. The pink and

orange wires are connected to the second normally closed contact of the flow

switch and may be used for remote alarm activation. The signal from the pink

wire will be supply voltage, to be provided to orange wire by customer, when no

water is flowing and zero voltage when the flow switch and local alarm are

activated. If a remote alarm is not used, the pink and orange wires must be

insulated at their free ends. Power to be routed using rigid conduit and a seal

fitting or Class 1, Division1 rated armored cable and an appropriate gland fitting.

See Electrical Wiring Diagram provided on installation drawing. Follow all

instructions in installation drawing and NEC code when installing unit.

OPERATION AND TEST INSTRUCTIONS

Test weekly. Instruct all employees in the use of emergency showers and eyewashes.

STEP 1: Apply power to the alarm branch circuit. The alarm should remain OFF.

STEP 2: Open the shower or eyewash flow valve. The alarm should sound and the light

should flash shortly after water flows from the system.

STEP 3: Shut off the flow valve. The alarm should turn off.

For more information about Haws products see our website: www.hawsco.com

HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

PARTS BREAKDOWN

PENDANT

LIGHT FIXTURE

GUARD 0002627451

HORN 0000091345

SP154DPDT FLOW SWITCH

FLASHER 0002469722

(INSIDE)

0002325488;

LED LAMP

0003225505

0004261000

APPROVED

DRAWN

PART NUMBER

DRAWING NO.

SCALE: SHEET OF

REV

DRAWING TYPE: SIZE: A

BYECN NO.

PAGE

DATE

ECN:

REVISED PER

CHKD

HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.

MODEL(S)

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAIL: HAWS@HAWSCO.COM

WEBSITE: WWW.HAWSCO.COM

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.

SLS

7/15/08

A11

0002077071

9001EXPC1D1

1:1

09/25/17

4 of 7

PARTS BREAKDOWN

5197

2017

CUSTOMER ELECTRICAL HOOKUP ON TOP

POWER NOT SUPPLIED) CONDUIT ENTRY FOR

ARMORED CABLE; MINIMUM BEND

152mm

6"MIN.

ARROW

MAIN JUNCTION BOX (120 VAC INCOMING

NOTES:

NOT SUPPLIED)

(RECOMMENDED

1-1/4" UNIONS

DIRECTION

NOTE FLOW

WATER SUPPLY

1-1/4" IPS

STRAIGHT

152mm

6"MIN.

STRAIGHT

CAUTION:

THIS ASSEMBLY AT ANY JOINT

AS DAMAGE WILL OCCUR

DO NOT DISASSEMBLE OR ROTATE

SWITCH MUST BE MOUNTED IN HORIZONTAL POSITION

FLOW SWITCH

1. AUDIBLE AND VISIBLE ALARM ACTIVATED WHEN

SHOWER OR EYEWASH IS IN USE.

2. ALL ELECTRICAL COMPONENTS UL CERTIFIED. 120VAC

SUPPLY VOLTAGE REQUIRED, APPROXIMATELY 100VA

ALL ELECTRICAL HOOKUPS TO MAIN JUNCTION BOX.

3. SUITABLE FOR CLASS I, DIV. 1 GROUPS C, D

TEMPERATURE RATING T4 (135°C) LOCATION.

4. LIGHT MUST BE ORIENTED IN A VERTICAL POSITION

AS SHOWN IN ORDER TO MEET NEMA 4 RATING.

5. INSTALLER MUST USE THREAD SEALANT, SUCH AS

APPLETON TLC3, RECOMMENDED FOR USE IN

HAZARDOUS LOCATIONS ON ALL ELECTRICAL NPT

CONNECTIONS.

HORN 6

SHOWER

RADIUS 5"; DO NOT CUT OR MODIFY.

SEE SHEET 2 FOR ELECTRICAL WIRING DIAGRAM

2X 1-1/4" PIPE CLAMP

2X WALL MOUNT FLANGE

MOUNTING HARDWARE

NOT SUPPLIED. SEE

BELOW

MOUNTING HOLE PATTERN 4X 1-5/8"

8 1/2"±1/2"

4X1-5/8"

8X Ø1/4"

2X 3/4" NIPPLE

SEE MOUNTING

SYSTEM DETAIL

MOUNTING SYSTEM DETAIL

(FOR PIPE OR WALL MOUNT)

FLASHING LIGHT

SEE SHEET 3 FOR

LAMP REPLACEMENT

APPROVED:

DRAWN:

PART NUMBER

DRAWING NO.

SCALE: SHEET OF

REV

DRAWING TYPE: SIZE: A

BY:ECN NO.

PAGE

DATE:

ECN:

REVISED PER

CHK'D.:

MODEL(S)

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

SLS

07/08

15361A00 11

0002077071.D

9001EXPC1D1 ALARM

1:1

09/25/17

4140 GC

5 of 7

INSTALLATION

5197

2017

(MAX PIPE SIZE Ø1 7/8")

(COPPER)

(BLK)

(ORG)

(PINK)

(110 VOLT)

(NEUTRAL)

NC 1

COMPONENT DESIGNATION:

FLSH - FLASHER RELAY

LT1 - RED LIGHT

FS - FLOW SWITCH

AH - ALARM HORN

COM 2

NC 2

NO 2 (WHT)

(BLK)

(BLUE)

COM 1

NO 1

(RED) FLSH

(WHT)

(RED) G

LT1

120 VAC POWER SOURCE

(CUSTOMER)

POWER SOURCE

LOAD

(CUSTOMER)

ELECTRICAL WIRING DIAGRAM

(GROUND)

APPROVED:

DRAWN:

PART NUMBER

DRAWING NO.

SCALE: SHEET OF

REV

DRAWING TYPE: SIZE: A

BY:ECN NO.

PAGE

DATE:

ECN:

REVISED PER

CHK'D.:

MODEL(S)

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

SLS

07/08

15361A00 11

0002077071.D

9001EXPC1D1 ALARM

1:1

09/25/17

4140 GC

6 of 7

INSTALLATION

5197

2017

PENDANT MOUNT

GUARD/GLOBE

ASSEMBLY

NOTES: (CONTINUED FROM SHEET 1)

6 LIGHT REPLACEMENT INSTRUCTIONS:

1) REMOVE GUARD/GLOBE ASSEMBLY:

FIRST LOOSEN SET SCREW (LOCATED ON GUARD WHERE

SHOWN). NEXT, ROTATE ASSEMBLY COUNTER CLOCKWISE

UNTIL GUARD IS FREE FROM PENDANT MOUNT AND LAMP

IS EXPOSED.

2) ONLY REPLACE LAMP WITH HAWS P/N 0003225505.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF

COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS 1,

DIVISION 1.

3) REPLACE GUARD/GLOBE ASSEMBLY:

ROTATE ASSEMBLY CLOCKWISE ONTO THE PENDANT MOUNT

UNTIL TIGHT AND TIGHTEN SET SCREW.

LAMP

SET SCREW

APPROVED:

DRAWN:

PART NUMBER

DRAWING NO.

SCALE: SHEET OF

REV

DRAWING TYPE: SIZE: A

BY:ECN NO.

PAGE

DATE:

ECN:

REVISED PER

CHK'D.:

MODEL(S)

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

SLS

07/08

15361A00 11

0002077071.D

9001EXPC1D1

1:1

09/25/17

4140 JP

7 of 7

INSTALLATION

5197

2017

Inhaltsverzeichnis

Andere Haws Sicherheitssystem Handbücher

Haws

Haws 9001 Alarm Series Betriebsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung