Haztec 7-1027 Series Bedienungsanleitung
Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
7-1027-X Wireless
Dash Mount Remote Control
M239 Issue 1.2 Created by: Technical - 1 - September 2020
Thank you for purchasing this Haztec product. Before proceeding with installation it is essential
to read and understand this instruction booklet.
Warning!
This product must be installed by persons competent in vehicle electrical installations
Care should be taken to ensure that water ingress cannot occur through mounting or
wiring holes
Regularly inspect the product to confirm correct operation
DO NOT allow solvents, fuels or acetone-based cleaners etc. to come into contact with
this product
Basic Operating Specifications:
Supply voltage:
7-1027-12 12VDC / 7-1027-24 24VDC
Maximum current draw:
25mA / 4mA (standby)
Operating temperature range:
-30OC to +70OC
Operating frequency:
433.92Mhz
Operating range:
65m
Dimensions (mm):
104 (W) x 86 (H) x 107 (D)
Kit Contents:
Qty
Description
1
Remote control unit
1
Wiring loom
2
Fixing screws
2
Retaining nuts
Remote dash-mount
For use with 7-1007 searchlights
12 or 24VDC versions
Wireless communication to
searchlight
Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
7-1027-X Wireless
Dash Mount Remote Control
M239 Issue 1.2 Created by: Technical - 2 - September 2020
Connection Instructions:
Wire
Connect to
Function
Red
Positive [+] via fuse
Main feed
Black
Negative [-]
Earth/Ground
Programming the Remote:
Avoid installation inside a metal surround as this will block the RF signal
Ensure that the searchlight is disconnected from the power source
Make sure that no other transmission devices are within 3m of the the remote control
unit and searchlight
Ensure that no other remote control (i.e. 7-SL007) units are programmed to the
searchlight before commencing
If another remote has been programmed; connect the 7-1027 as per the connection
instructions, then press and hold the programming button and connect the searchlight to
the power
Allow the searchlight to flash more than 4 times, then release the programming button
and disconnect the power
You can now proceed with programming the 7-1027 as the main controller
Connect the remote unit to power as per connection instructions
Press and hold the programming button on the rear of the remote unit
Reconnect power to the searchlight. The searchlight will flash 1-4 times to acknowledge
that the remote has been programmed
Release the programming button and disconnect power to the searchlight
Reconnect the power and check for correct operation
To program additional remotes; repeat the above process for the first unit, then press
and hold the programming button on the second unit within 5 seconds of programming
the first remote
The searchlight will again flash to acknowledge that programming has been successful
A searchlight can accept upto 4 programmed remote control units
Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
7-1027-X Wireless
Dash Mount Remote Control
M239 Issue 1.2 Created by: Technical - 3 - September 2020
Installation:
Cut a 80x80mm hole into the mounting surface so that the remote unit fits neatly in place
Use the remote unit as a template to mark the mounting hole positions. Drill the fixing
holes using a suitable sized drill bit for the screw fixings being used
Plug the wiring loom into the rear of the unit and connect the power as per connection
instructions
Attach the remote unit to the mounting surface using the screws provide or customer
supplied fixings if desired
Dimensional Drawing:
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Haztec Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
