HearthStone Tudor Fehlerbehebungshandbuch

Owner’s Manual & Installation Guide for the

Tudor (8120) GAS-FIRED DIRECT-VENT HEATER

READ THIS OWNER’S MANUAL -Operate and

maintain this gas heater according to this instruction manual.

WARNING: If the information in these

instructions is not followed exactly, a fire or

explosion may result causing property damage,

personal injury or loss of life.

Do not store or use gasoline or other flammable

vapors and liquids near this or any other gas

appliance.

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch electrical switches; do not use

the phone in your building.

•Immediately call your gas supplier from a

neighbors phone. Follow your gas supplier’s

instructions.

•If you cannot reach your gas supplier, call the

fire department.

A qualified installer, service agency or gas supplier

must perform installation and service.

AVERTISSEMENT: Assurez-vous de bien

suivre les instructions donné dans cette notice

pour réduire au minimum le risque d’incendie

ou pour éviter tout dommage matéeriel, toute

blessure ou la mort.

Ne pas entresposer ni utiliser d’essence ni d’autre

vaperurs ou liquides inflammables dans le

voisinage de cet apprareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR

DE GAZ:

•Ne pas tenter d’allumer d’appareil.

•Ne touchez à aucun interrupteur.

Ne pas vous

servir des téléphones se trouvant dans le

batiment où vous vous trouvez.

•Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

•

Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le service dos incendies.

L’installation et service doit être exécuté par un

qualifié installer, a

gence de service ou le

fournisseur de gaz.

10-04-04

Model #8120

HearthStone Quality Home Heating Products, Inc.

317 Stafford Avenue,

Morrisville, Vermont 05661-8695

E-Mail: [email protected]

HearthStone Quality Home Heating Products Inc Tudor Model #8120

INFORMATION SHEET

Use this page to record all relevant information concerning the purchase, installation, and maintenance

of your Tudor Gas-Fired Direct-Vent heater. This information will facilitate servicing, purchase of

replacement parts, and warranty claims (if necessary). Keep your original receipt in a safe place as

proof of purchase.

Serial Number:

Fuel type (check one) Natural Gas Liquid Propane

Sold by:

Phone: Date of Purchase:

Installed by:

Phone: Date of Installation:

Gas Supplier:

Phone:

Read this Owner’s Manual before installing or operating the Tudor. Retain this manual for future reference.

SERVICE RECORD Important -Verify proper operation after servicing!

Date Who Performed Work Work Performed Notes:

WHAT WHEN WHAT WHEN

Firebox Cleaning............. annually Door Gasket.................... Replacement as needed

Glass Cleaning................ as needed

HearthStone Quality Home Heating Products Inc Tudor Model #8120

TABLE OF CONTENTS

INTRODUCTION.................................................................3

SPECIFICATIONS:........................................................5

OWNER’S INFORMATION.................................................6

INSTALLER’S INFORMATION...........................................7

ITEMS REQUIREDFOR INSTALLATION...........................7

UNPACKING AND INSPECTION.........................................7

CLEARANCETO COMBUSTIBLES.....................................8

VENTING INFORMATION................................................11

ELECTRICAL CONNECTIONS..........................................16

GAS SUPPLY & CONNECTIONS.....................................18

LOG PLACEMENT............................................................19

INITIALADJUSTMENTS...................................................22

ROUTINE MAINTENANCEAND CARE...........................26

PARTS LISTS....................................................................28

LIMITED WARRANTIES..........................................33

INTRODUCTION

Congratulations on your purchase of

HearthStone’s Tudor Gas-Fired Direct Vent

heater. The Tudor incorporates the latest in

balanced vent gas technology, which will

provide you with clean, efficient heat for

years to come. Combustion air comes

directly from the outside of your home to the

sealed firebox system, eliminating the

potential for annoying back drafts or other

problems associated with home

depressurization.

The Tudor will provide you with years of

practical and convenient service. However,

as with any gas appliance, the unit must be

properly and safely installed and maintained

by qualified service personnel to ensure safe

and trouble-free operation. It includes the

new TEK Firelog technology, which is an

amazing blend of realistic flames and

glowing embers with incredible heating

characteristics.

READ THIS OWNER’S MANUAL

Operate and maintain this gas heater

according to the instructions in this manual.

For your safety, and years of trouble free

operation, read this manual in its entirety.

By following a few simple safety

precautions and by performing minimal

maintenance, the unit will remain appealing

while providing years of quality

performance.

WARNING!

A qualified service technician should do

installation, and repair. A qualified

service technician must inspect the

appliance before use, and at least

annually. More frequent cleaning may be

required due to excessive lint from

carpeting, bedding material, pets, etc. It is

imperative that the control

compartments, burners, and circulating

air passages of the appliance are kept

clean and free of obstructions. (S’assurer

que le brûleur et le compartiment des

commandes sont propres. Voir les

instructions d’installation et d’utilisation

qui accompagnent l’appareil.)

WARNING: Do not operate this appliance

with the glass, or any panel removed,

cracked, or broken. Do not subject the door

to abuse, such as striking or slamming shut.

Replacement of the glass panel should be

done by a licensed or qualified service

person.

NEVER BURN PAPER, WOOD OR OTHER

MATERIALS

This gas heater is designed to burn natural

gas or liquid propane (LP). Never burn any

fuel not intended for use with this unit.

HearthStone Quality Home Heating Products Inc Tudor Model #8120

HOT SURFACES

Certain exposed surfaces of the Tudor will

reach high temperatures during normal

operation. Clearances to combustibles must

be maintained, as specified in the

“Clearances To Combustibles” section of

this manual.

Do not use this appliance if any part has been

under water. Immediately call a qualified

service technician to inspect the heater and to

replace any part of the control system and gas

control that has been under water. (Ne pas se

servir de cet appareil s’il a été plongé dans

l’eau, complétement ou en partie. Appeler un

technicien qualifié pour inspector l’appareil et

remplacer toute partie du systéme de contrôle

et toute commande qui ont été plunges dans

l’lau.)

WARNING

This gas appliance must not be connected to

a chimney flue serving a separate solid-fuel

burning appliance. NEVER VENT THE GAS

HEATER TO OTHER ROOMS OR BUILDINGS.

Masonry Conversions Kits are an acceptable

venting option.

Due to high temperatures the appliance

should be located out of traffic and away

from furniture, draperies, clothing and

flammable materials. Children and

adults should be alerted to the hazards of

high surface temperatures and should

stay away to avoid burns to skin or

clothing ignition. Young children should

be carefully supervised when in the same

room as the appliance. Clothing or other

flammable material should not be placed

on or near the appliance. (Surveille les

enfants. Garder les vêtements, les meubles,

l’essence ou autres liquides à vapeur

inflammables lin de l’appareil.)

FIRE HAZARD

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity

of this appliance. The Tudor should be

located out of traffic and away from

furniture, draperies, clothing, and flammable

material.

Any shield, door, or safety screen

component removed for servicing will be

replaced prior to operating the unit.

Certified for use by:

Board of State Examiners of Plumbers and

Gasfitters

100 Cambridge Street, Room 1511

Boston, Massachusetts 02202

HearthStone Quality Home Heating Products Inc Tudor Model #8120

SPECIFICATIONS:

LISTED AS: Gas-Fired Direct-Vent Fireplace Heater

Model: Tudor Direct-Vent Gas Fireplace Heater (8120)

Testing Agency: OMNI-Test Laboratories, Inc.

Tested to: ANSI Z21.88-B2003, CSA 2.33-M02, CAN/CGA2.17-M91

Certified for Canada, CSA P.4.1

Approved for Mobile Home Installation

Figure 1Tudor Dimensions

FUEL TYPE: NG LP

INPUT RATING (Btu/hr) 0-2000 ft 11,500 11,200

ORIFICE SIZE (DMS) 0-2000 ft 53 63

MANIFOLD PRESSURE-LO SETTING (in. W.c./kpa) 1.6/0.42 6.4/1.59

MANIFOLD PRESSURE-HI SETTING (in. W.c./kpa) 3.5/1.15 10.0/2.48

INLET PRESSURE-LO (in.w.c./kpa) 5.0/1.24 11.0/2.88

MINIMUMINPUT RATING (btu/hr) 7000 8500

MAXIMUMOUTPUT (btu/hr) 0-2000 ft 7652 7494

HearthStone Quality Home Heating Products Inc Tudor Model #8120

OWNER’S INFORMATION

The installation must conform with local

codes or, in the absences of local codes, the

current National Fuel Gas Code, ANSI Z223.1

(NFPA 54) or CAN/CGA B149 Installation

Code. (Installer l’appareil selon les codes ou

règlements locaux, ou, en l’absence de tels

règlements, selon les Codes d’installation

CAN/CGA-B149.)Do not use this appliance

if any part has been under water.

Immediately call a qualified service

technician to inspect the heater and to

replace any part of the control system and

gas control that has been under water. (Ne

pas se servir de cet appareil s’il a été plongé

dans l’eau, complètement ou en partie.

Appeler un technicien qualifié pour inspector

l’appareil et remplacer toute partie du système

de contrôle et toute commande qui ont été

plongés dans l’lau.)

DAILY OPERATION

The Tudor is easily operated by the

homeowner once installed and adjusted by

qualified service personnel. The unit can be

controlled via the wall-mounted thermostat

during the heating season. Set the thermostat

to the desired room temperature and the unit

will cycle on and off as required. By

adjusting the variable output control located

on the gas control valve, the rate of heat

output can be varied to meet the heating

requirements of the season. Choosing a low

flame setting will result in longer burn

cycles at a reduced output, while choosing a

high flame setting will result in a shorter,

hotter burn cycle. Through trial and error,

the homeowner can select the optimum

flame size for their setting and application.

During the summer non-heating season,

switch the wall thermostat to “OFF”, and

turn off the pilot. This will improve the

overall efficiency of the unit as the heat

from the pilot is wasted. When putting the

unit back into service, follow the lighting

instructions described on page 23.

When the unit is first lit, especially when

cool, it is normal to experience some

condensation on the inside of the window

glass. This condensation will burn off within

the first few minutes of operation. If

continuous condensation on the window

glass or dripping water from any part of the

unit or venting system (chimney) is noted,

immediately discontinue operation of the

unit and contact qualified service personnel.

Clean the area around, under, and behind the

unit on a regular basis to prevent the

accumulation of dust and lint.

The Tudor requires minimal routine

maintenance and care. It should always be

cool and off when being cleaned, or

serviced. Once a year, the unit, and venting

system should be inspected by qualified

service personnel to insure that they are

clean, free of obstruction, safe, and in good

working order. If service or maintenance is

required, qualified service personnel should

perform it.

SERVICE CAUTION

If you believe your Tudor is not, in any way,

performing properly, immediately

discontinue operation until the unit has been

inspected and approved by qualified service

personnel. Prior to servicing the unit, turn

the valve control knob clockwise to “OFF”.

The unit should be cool prior to servicing

and cleaning. Use of any components not

supplied by HearthStone on the stove voids

all warranties. Do not substitute

components.

HearthStone Quality Home Heating Products Inc Tudor Model #8120

INSTALLER’S INFORMATION

CODES

Adhere to all local codes or, in their

absence, the latest edition of THE

NATIONAL FUEL GAS CODE ANSI

Z223.1 (NFPA 54) or CAN/CGA B149

Installation Code that can be obtained from:

AMERICAN NATIONAL STANDARDS

INSTITUTE, INC.

1430 BROADWAY

NEW YORK, NY 10018

NATIONAL FIRE PROTECTION

ASSOCIATION, INC.

BATTERY MARCH PARK

QUINCY, MA 02269

A manufactured home (mobile) OEM

installation must conform with the

Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280

(U.S.) or Standard for Manufactured Home

Installation, ANSI/NCBCS A225.1 or

Standard for Gas Equipped Recreational

Vehicles and mobile Housing, CSA

Z240.4.CAN/SCA Z240 MH (Canada).

(Installer l’appareil selon les codes ou

règlements locaux, ou, en l’absence de tels

règlements, selon les Codes d’installation

CAN/CGA-B149.)

ITEMS REQUIRED FOR INSTALLATION

* External regulator (for propane/L.P.G. only)

* Piping which complies with local codes

* Pipe sealant approved for use with

propane/L.P.G. (resistant to sulfur compounds)

* Manual shutoff valve

* Sediment trap (see page 18)

* Tee joint

* Pipe wrench

* Phillips head screwdriver

* 7/16-inch wrench

* Other parts as required by local code

*Safety Glasses

*Gloves

PACKING LIST

1-Tudor Gas-Fired Heater

1-TEK Burner

2-Decorative TEK Firelogs

1-Tudor top casting

1-Owner’s Manual

1-Thermostat

1-40’ Thermostat wire

1-Wall thimble Insulation Blanket

1-Warranty Validation Form

Note: Vent kits and components are supplied

separately. Failure to use the venting

components specified by HearthStone

QHHP, Inc. will void your warranty and

could risk a fire.

UNPACKING AND INSPECTION

Unpack and Inspect for Damage

The Tudor is packaged by the manufacturer

to withstand shipment without damage.

However, damage can still occur during

transit; so take care to inspect for damage

when unpacking and installing the unit. If

any damage, or missing parts are detected,

immediately contact your dealer.

Do not install, or put into service, a

damaged or incomplete heater.

The Tudor requires a pilot shield. This

shield is shipped with the unit. Make sure

the sure the shield is installed over the

pilot with the open end is to the right

(when you are facing the front of the

stove)

Inspect the Tudor for visible or concealed

damage. The unit should appear to be square

and true. The sheet metal parts should be

smooth and free of bends and dents. The

enameled cast iron should be free of chips or

cracks. If visible or concealed damage is

HearthStone Quality Home Heating Products Inc Tudor Model #8120

found or suspected, contact your dealer for

instructions.

With the accessory box removed and set

aside, take care not to mar or chip the

enameled legs, if applicable. Have someone

help lift the stove out of the shipping box

and set it into place.

The TEK Burner and TEK Firelogs supplied

with the Tudor are contained in the

accessory box. Always use great care when

handling the decorative fire logs, as they are

fragile and subject to damage and breakage

if handled roughly. If a broken log is

encountered, contact your dealer for

replacement logs. Otherwise, set the logs

aside until called for during the installation.

INSTALLING THE TUDOR

A complete Tudor REQUIRES the

purchase of one of the following panel

kits;

91-8220010 Curio Matte (cast iron)

91-8220020 Curio Brown

91-8220059 Curio Blue/black

91-8220310 Keepsake Matte (grill + cast)

91-8220320 Keepsake Brown

91-8220359 Keepsake Blue/black

91-8220641 Heirloom Polished (stone)

91-8220653 Heirloom Brown

91-68200 Tile Insulation kit (Must be

used with self purchased

tiles) Do not paint, plaster or

finish the tiles in any way.

This may risk off gassing or a

fire.

HEARTH REQUIREMENT/FLOOR

PROTECTION

The Tudor may be placed on any surface or

wood floor, carpeting, or vinyl tile, with or

without legs. Installations must meet local

codes.

Removing the Tudor’s legs

The Tudor has the unique possibility of

having its legs removed, allowing for the

unit to rest on its base. To do this, simply

use two 7/16” wrenches or ratchets and

loosen and remove the two centermost ¼-20

bolts and nuts holding the legs on. These can

be reached the easiest from behind the unit

and should be removed prior to any other

connections have been made. Once

removed, lift the unit off the legs and set in

the desired location.

CLEARANCE TO COMBUSTIBLES

Due to high surface temperatures, the unit

should be located out of traffic and away

from furniture and draperies. Clothing and

other flammable material should not be

placed on or near the heater. When

positioning the unit always maintain

adequate clearances around air openings into

the combustion chamber and allow for

adequate ventilation. Minimum clearances

to combustibles must be maintained as

shown in the illustrations of the Clearances

To Combustibles section.

Be sure to consider the need for access to

the gas control valve access door on the

front of the unit as well as full access for

periodic cleaning and servicing.

Caution: These clearances represent

minimum distances in all cases, which,

through testing in an independent

laboratory to ANSI and CSA standards,

will prevent fire or spontaneous

combustion. We do not control the

combustible materials exposed to heat by

this product; therefore, an assessment

must be made by the installer to prevent

consequential damage of walls and

flooring.

HearthStone Quality Home Heating Products Inc Tudor Model #8120

* For fully operational doors use a 3" corner

clearance

Clearance To Combustibles and

Alcove Dimensions.

Minimum Alcove height is 40"

Figure 2Clearance to combustibles

6" straight

Wall pass

through

Insulation

blanket

Termination

cap

Minumum Venting Components

-Rear wall clearance = 0"

Figure 3Minimum vent clearances

HearthStone Quality Home Heating Products Inc Tudor Model #8120

Acceptable Direct-Vent TERMINATION Cap locations.

Figure 4Termination clearances

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HearthStone Gasheizung Handbücher

HearthStone

HearthStone STERLING "G" 8531 Bedienungsanleitung

HearthStone

HearthStone TUCSON 8745 Bedienungsanleitung

HearthStone

HearthStone Champlain 8302 Bedienungsanleitung

HearthStone

HearthStone Stowe 8320 Fehlerbehebungshandbuch

HearthStone

HearthStone Sterling-Ht 8532 Fehlerbehebungshandbuch

HearthStone

HearthStone FS-16N-TV Bedienungsanleitung

HearthStone

HearthStone Stowe Bedienungsanleitung

HearthStone

HearthStone TUCSON Bedienungsanleitung

HearthStone

HearthStone 8160 Bedienungsanleitung

HearthStone

HearthStone Santa Fe 8761 Bedienungsanleitung

HearthStone

HearthStone Tudor 8120 Programmierhandbuch

HearthStone

HearthStone Tribute DV 8050 Programmierhandbuch

HearthStone

HearthStone Bristol DX Bedienungsanleitung

HearthStone

HearthStone AURORA 8901 Series Sicherheitsleitfaden

HearthStone

HearthStone Sterling-Ht 8532 Fehlerbehebungshandbuch

HearthStone

HearthStone Sterling-Ht 8532 Fehlerbehebungshandbuch

HearthStone

HearthStone 8050 Fehlerbehebungshandbuch

HearthStone

HearthStone Champlain 8303 Bedienungsanleitung

HearthStone

HearthStone hase-Bari 8180 Bedienungsanleitung

HearthStone

HearthStone Santa Fe Fehlerbehebungshandbuch

HearthStone

HearthStone Stowe 8324 Bedienungsanleitung

HearthStone

HearthStone STERLING "G" B-VENT 8521 Bedienungsanleitung

HearthStone

HearthStone Aurora 8900 Series Bedienungsanleitung

HearthStone

HearthStone Waitsfield DX 8770 Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung