Heartland BEF-23BM03 Bedienungsanleitung

OWNER’S MANUAL

18 Inch Black Electric Fireplace

AC 120V 60Hz 1200W

WARNING

Read and understand this entire owner’s manual, including all safety

information, before plugging in or using this product. Failure to do so could

result in fire, electric shock, or serious personal injury.

CAUTION

Keep this owner’s manual for future reference. If you sell or give this

product away, make sure this manual accompanies this product.

ELECTRIC FIREPLACE HEATER

MODEL # : BEF-23BM03

IMPORTANT SAFETY INFORMATION!

WARNING

ALWAYS keep electric cords,home furnishings,drapes,clothing,papers, or other

combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the

bottom, sides, and rear of this heater.

DO NOT place the heater near a bed because objects such as pillows or blankets can fall

off the bed and be ignited by the heater.

DO NOT COVER this heater or block the air vents at all. Doing so could cause a fire.

AVOID fire or electric shock! NEVER insert or allow any foreign objects to enter the

ventilation or exhaust openings of this heater.

Prevent Fire! Keep all flammable liquids, like gasoline or paint, away from this heater. This

heater produces arcing sparks that could ignite flammable liquids.

DO NOT cover this heater in any manner. Doing so could block the air flow and cause the

unit to overheat, or could ignite the material covering the heater.

NEVER run the power cord under carpet, rugs, runners, or any other covering. Doing so

could cause the cord or materials covering the cord to overheat.

AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other

blockage. Unplug the unit and clean with a vacuum ONLY.DO NOT rinse or get wet.

WARNING

For residential use only! NOT for commercial use! NEVER use this fireplace for other than

its intended purpose.

ALWAYS HANG UNIT BEFORE USE.DO NOT turn on or use while the unit is sitting on the

floor, ground, or other surface.

The wall mount system is designed for use ONLY with this product. NEVER use a wall

mount system from another manufacturer.

Use extreme caution if using this heater near children, or where children may be present.

NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.

This heater is hot when in use.AVOID INJURY! DO NOT TOUCH hot surfaces, or attempt

to move this heater while it is hot.

ALWAYS turn this heater off before unplugging it from the outlet.

AVOID INJURY! Keep the cord from crossing traffic areas to avoid tripping.

NEVER modify this fireplace. Doing so could result in personal injury or property damage.

Modification of this fireplace completely voids all warranties.

Discontinue use if this fireplace malfunctions or is dropped or damaged in any manner.

ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.

WARNING

Risk of electric shock!DO NOT OPEN! No user-serviceable parts inside!

ALWAYS disconnect this unit from the power supply before performing any assembly or

cleaning, before replacing the light bulb, or before relocating the electric fireplace.

NEVER use this heater in bathrooms, laundry rooms, or any other location where the

heater could fall into a bathtub or pool,become damp or come in contact with water.

NEVER hang this unit on a wall directly below an electrical outlet.

NEVER operate this heater if the power cord or plug has become damaged, or if the

grounding pin is damaged or missing.

Place the heater near a wall outlet so an extension cord is not needed. If an extension cord is

needed, the gauge of the cord must be at least 14AWG, and the rating must be at least

1875 Watts.NEVER use a smaller gauge cord with a lower rating. Doing so may result in

fire or electric shock.

Avoid hazards due to resetting of the thermal cut-off switch. NEVER control this unit with a

timer, or allow it to be on a circuit regularly switched off by the utility.

ONLY use this heater on a 110~120 Volt 15 Amp grounded circuit.NEVER overload the

circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit

before the next use. Avoid plugging other appliances into the same circuit as this heater.

NEVER plug this heater into an outlet that is old,cracked, or has any loose wires or

connections. Plugging this heater into a faulty outlet could result in electric arcing within

the outlet that could cause the outlet to overheat or catch fire.

ALWAYS check your heater cord and plug connections with each use!

i) MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs

can cause the outlet to overheat.

ii) Heaters draw more current than small appliances. Overheating may occur even if it

has not occurred with the use of other appliances.

iii) During use check frequently to see if the plug outlet or face plate is HOT!

iv) If the outlet or face plate is HOT,discontinue use immediately and have a qualified

electrician inspect and/or replace the faulty outlets.

The cord supplied with the heater has a

plug with two blades (live and neutral) and

one round pin (ground). If a 3-slot

receptacle is not available, an adapter

MUST be used. The adapter MUST be

properly grounded to the outlet box (see

figure at right).

Preparation

This product includes a GLASS panel! Always use extreme caution when using. Failure

to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check

the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please

recycle whenever possible.

Parts and Hardware

A– Fireplace ( 1 )

Operation

Read and understand this entire owner’s manual, including all safety information,

before plugging in or using this product. Failure to do so could result in electric shock,

fire, serious injury, or death.

Power

Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY

INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not

loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the

same circuit.

Methods of Operation

This electric fireplace can be operated by the CONTROL BUTTONS, located on the Front of the

fireplace (see figure below), or by the battery-powered REMOTE CONTROL.

Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, and

heed all warnings.

D – Remote Control （1） E- Instruction Manual (1)

B – Wood Screws (4) C – Drywall anchors (4)

Front View

Control Panel Remote Control

Remote Control and Control Panel Operation

BUTTON

FUNCTION

ACTION & INDICATION

POWER

ON: Enables control panel functions and

remote control. Turns on flame effect.

OFF: Disables control panel functions and

remote control. Turns off flame effect.

1. Press once. LED Indicator light turns on.

Power turns on. All functions enabled.

2. Press again. Flame effect turns off.

Power and all functions turn off.

TIMER

TIMER button: Controls timer settings to

turn off fireplace at selected time.

Settings range from 1 hour to 8 hours.

1. Press once. LED Indicator light turns on.

Timer is set to 1 hour.

2. Press again until desired setting is

reached. Indicator lights show setting.

FLAME -

FLAME “-”: Makes flame effect dimmer.

NOTE: Flame effect stays on until power

button is turned off. Flame effect must be

on for heater to turn on.

1. Press once. LED Indicator light turns

on, Flame effect dimmer get ready to

adjust.

2. Press again until desired setting is

reached. Flame effect continues to get

dimmer each time button is pressed.

Hot Air Vents

Control Panel

Temperature Limiting Control

This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe

temperature, the heater will automatically turn OFF. To reset:

1. Unplug the power cord from the outlet.

2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.

3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are,

use a vacuum to clean the vent areas.

4. With the POWER switch in the OFF position, plug the power cord back into the outlet.

5. If the problem continues, have your outlet and wiring inspected by a professional.

FLAME +

FLAME “+”: Makes flame effect brighter.

NOTE: Flame effect stays on until power

button is turned off. Flame effect must be

on for heater to turn on.

2. 1. Press once. LED Indicator light turns

on, Flame effect brighter get ready to

adjust.

2. Press again until desired setting is

reached. Flame effect continues to get

brighter each time button is pressed.

HEATER

HEATER button: Turns heater on and off.

NOTE: The heater only works when the

flame effect is on. If the flame effect is off,

the heater will not turn on.

NOTE: To prevent overheating, the heater

blows cool air for 30 seconds after it turns

off.

1. Press once. LED Indicator lights up.

Continue press Fan blows cool air for 30

seconds. Then Low heater turns on and

blows warm air.

2. Press again. LED Indicator lights up.

High heater turns on and blows hot air.

3. Press again. Heaters turn off.

The fan blows cool air, then turns off.

NOTICE

To improve operation, aim the remote control at the front of the fireplace. DO NOT

press the buttons too quickly. Give the unit time to respond to each command.

Remote Control Battery Information

This remote control uses two AAA batteries (Not included).

NEVER dispose of batteries in ﬁre. Failure to observe this precaution may result in an

explosion. Dispose of batteries at your local hazardous material processing center.

Care and Maintenance

Cleaning

ALWAYS turn the heater OFF and unplug the power cord from the outlet before

cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in

electric shock, fire, or personal injury.

NEVER immerse in water or spray with water. Doing so could result in electric shock,

fire, or personal injury.

Metal:

Buff using a soft cloth, slightly dampened with a citrus oil-based product.

DO NOT use brass polish or household cleaners as these products will damage the metal trim.

Glass:

Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper

towel or lint-free cloth.

NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents:

Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic:

Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.

NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Maintenance

Risk of electric shock!DO NOT OPEN any panels. No user-serviceable parts inside!

ALWAYS turn the heater OFF and unplug the power cord from the outlet before

cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in

electric shock, fire, or personal injury.

Electrical and Moving Parts:

The fan motors are lubricated at the factory and will not require lubrication.

Electrical components are integrated in the fireplace and are not serviceable by the consumer.

Storage:

Store heater in a clean dry place when not in use.

and will not turn on.

on.

Troubleshooting

WARNING

DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE.

ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

Problem Possible Cause Solution

1. Fireplace turns off 1. Fireplace has overheated

and safety devise has caused

thermal switch to disconnect

or home circuit breaker has

opened.

2. Flame is not moving. 1. Loose wiring.

2. Flame motor defective.

3.Flame rod out of place

3. Flame is not visible. 1. Wiring is loose.

4.Log set and/or is not

glowing.

6. Fireplace will not

come on when

switch is flipped to

ON.

7. Heater does not

provide heat when

turned on.

1. Reset switch by turning main

power switch off and waiting 10

minutes then turning it back on

or reset circuit breaker.

1. Inspect wiring for loose con-

nections.

2. Call a qualified service techni-

cian to replace flame motor.

3."Flame Rod" out of place due to

rough transit/handling of the

product. This issue can be

corrected as simple as removing

the glass, flipping the fireplace

upside down, removing a set of

screws that are holding the

bottom frame plate and placing

the flame rod back into place.

1. Disconnect from power source

and inspect wiring for loose

connections and repair or

replace if necessary.

2.Push the flame button to high

1.Wiring is loose.

1.Disconnect from power source

and inspect wiring for loose

connections and repair or replace

if necessary.

1. Fireplace is not plugged in to

an electrical outlet.

2. Control failure.

1. Check plug.

2. Call a qualified service techni-

cian.

1.Thermal switch has been

tripped.

2. Wiring is loose.

3. Heater is defective.

1. Turn unit off and unplug unit

for 10 minutes. Plug back in and

turn unit on. If plug cannot be

reached, follow directions for

tripped circuit breaker.

2. Disconnect from power source

and inspect wiring for loose

connections and repair or

replace if necessary.

3. Replace heater.

Inhaltsverzeichnis

Andere Heartland Kamin im Innenbereich Handbücher

Heartland

Heartland IF-1350TCL Bedienungsanleitung

Heartland

Heartland BEF-26BM02 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch