Heat & Glo PORTRAIT-6-BK Bedienungsanleitung

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

Leave this manual with party responsible for use

and operation.

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during instal-

lation. Sheet metal edges are sharp.

CAUTION! Do not install damaged components.

WARNING! Risk of Fire! Combustible materials MUST

NOT overlap or be placed behind a decorative front.

Portrait Decorative Front

PORTRAIT-6-BK, PORTRAIT-8-BK

Models: 6K,8K, 6KL,8KL, 6KX, 8KX, 6KMOD, 8KMOD

- Installation Instructions -

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and must be installed for

the protection of children and other at-risk

individuals.

WARNING! Risk of Fire! DO NOT apply combustible

materials beyond the minimum clearances. Comply with

all minimum clearances to combustibles as specied.

Overlapping materials could ignite and will interfere with

proper operation of decorative fronts.

Special TV and Mantel Clearance Requirements

The Portrait decorative front has unique requirements for

clearances to TV’s and mantels. Verify that the appliance

is installed in compliance with the required clearances to

mantels. The installation must comply with the specied

TV Guidelines and Combustible Mantel and Non-Com-

bustible Mantel diagrams included in this instruction.

Refer to the appliance Installation Manual for additional

information.

IMPORTANT INSTALLATION INFORMATION

MAINTAIN required mantel and TV clearances to avoid

damage to nishing materials and/or TV.

Note: Measurement is taken from top/side of the

opening, NOT the top/side of the appliance.

Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear-

ances as specied. Mantel MUST be fastened to wall

with no gaps.

• Framing closer than the minimums listed must be

constructed entirely of non-combustible materials (i.e.,

steel studs, concrete board, etc.).

• No gaps allowed between the wall and the bottom of the

mantel.

• Combustible mantel legs and wall projections may be

applied over the non-combustible board supplied with

the appliance. Follow guidelines as shown in the gures

below for mantels, mantel legs and wall projections.

Verify that mantel clearance requirements are maintained

for combustible or non-combustible mantels as shown in

Figure 1 and Figure 2. Refer to Figure 3 and Figure 4 if

the Passive Heat Kit is installed.

Good Faith TV Guidelines

See Figure 5 for TV Clearances.

Good Faith Wall Surface Temperatures

See Figure 6 for wall surface temperatures. Note that

temperatures vary based on appliance model installed

and whether or not the Passive Heat Kit is installed.

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

Combustible Mantels - Portrait Decorative Front

Figure 1 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

(Portrait Fronts)

2-1/2

TO CEILING

Measurement from fireplace

opening to bottom of appliance:

Note: All

measurements

in inches.

Note: Measurement is taken from top of the opening,

NOT the top of the fireplace.

= 33-1/2 IN. (36 INCH MODELS)

= 35-1/2 IN. (42 INCH MODELS)

Combustible Mantels - Passive Heat Installed

Figure 3 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

with Passive Heat Kit Installed

Measurement from fireplace

opening to bottom of appliance:

Note:

All measurements

in inches.

Note: Measurement is taken from top of the opening,

NOT the top of the fireplace.

2-1/2

TO CEILING

= 33-1/2 IN. (36 INCH MODELS)

= 35-1/2 IN. (42 INCH MODELS)

TO CEILING

Measurement from fireplace

opening to bottom of appliance:

= 33-1/2 IN. (36 INCH MODELS)

= 35-1/2 IN. (42 INCH MODELS)

Note: All

measurements

in inches.

Note: Measurement is taken from top of the opening,

Non-Combustible Mantels - Portrait Decorative Front

Figure 2 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

(Portrait Fronts)

Measurement from fireplace

opening to bottom of appliance:

Note: Measurement is taken from top of the opening,

TO CEILING

= 33-1/2 IN. (36 INCH MODELS)

= 35-1/2 IN. (42 INCH MODELS)

Figure 4 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

with Passive Heat Kit Installed

Non-Combustible Mantels - Passive Heat Installed

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

Figure 5 Good Faith TV Guidelines - Portrait Decorative Front

Good Faith Guidelines for TV Installations Above Appliance - Portrait Decorative Front

Item Minimum Dimensions

2.5 inches

B 2 inches minimum to 3 inches maximum

Passive Heat NOT Installed = 18 inches

D Wall Brkt + TV Thickness + 2.5 inches

Appliance

Mantel

Notes:

1. These are good faith recommended clearances only and not a guarantee of compliance with all TV

manufacturers’ maximum allowable operating temperatures.

2. Since every home has unique air flow characteristics and maximum allowable operating temperatures

can vary from manufacturer to manufacturer and from model to model, actual TV temperatures should

be validated at the time of each installation. TVs should not be used in situations where the actual TV

temperature exceeds the manufacturers’ maximum allowable operating temperatures identified in the

TV’s technical specifications. Contact the TV’s manufacturer directly if you cannot locate this

information or have questions regarding the information.

3. Mantel height and depth must conform to mantle requirements specified in the appliance installation

manual.

4. “C” dimension taken from the top of the hood or appliance opening.

5. Suggestions on how to further reduce TV temperatures:

a. Increase “A” dimension.

b. Increase “C” dimension, however, increasing “B” dimension beyond maximum recommended

typically results in higher temperatures.

TV Wall

Bracket

Appliance

TV on the wall TV recessed into the wall

Appliance Opening Appliance Opening

Passive Heat Installed = 6 inches

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

6 in.

18 in.

24 in.

30 in.

TO CEILING

12 in.

A°F

APPLIANCE FRONT

B°F

C°F

D°F

E°F

FIREPLACE

OPENING

TEMPERATURE

APPLIANCE MODEL

6KX / 8 KX

With Passive Heat Kit

Installed

6K / 8K

6KL / 8KL

6KMOD/8KMOD

6K / 8K

6KL / 8KL

6KMOD/8KMOD

With Passive Heat Kit

Installed

A 230 190 167 190

B 200 160 155 160

C 170 130 152 112

D 150 110 143 103

E 150 110 147 107

Figure 6 Good Faith Wall Surface Temperatures Above Appliance - PORTRAIT Decorative Front

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

Note: These fronts have optional decorative trim kits. If an

optional trim kit will be used, install it prior to installing the

front on the appliance. Reference the instructions included

with the trim kit and the Service Parts section of this

instruction for more detail.

Finishing Material/Method

These decorative fronts are designed to be installed as

Overlap Fit or Inside Fit.

Inside Fit Method:

When installing a decorative front using the Inside Fit

method, the factory-supplied nishing strips must be in-

stalled prior to installation of the nishing material. The

nishing strips ship with the appliance and are located in

the control cavity underneath the rebox. The nishing

strips must be removed before installing the decorative

front. Finishing strips will add the proper clearances for

the installation of the front.

Typically, the inside t method is only used when non-

combustible nish material greater than 1 inch is used

(such as cultured stone). This nish material is installed

adjacent to the decorative front sides and top. When in-

stalled, the back of the decorative front contacts the black

surround on the replace, thus the decorative front is “in-

side” the adjacent nish material. Refer to the appliance

Installation Manual for more detailed information.

Overlap Fit Method:

The factory-supplied nishing strips are not needed for

this method of nishing. Remove the nishing strips from

the control cavity of the appliance and discard.

Non-combustible nish material that is 1 inch or less

(such as marble or tile) is installed up to the replace

opening on the sides and top. When installed, the back of

the decorative front contacts the face of the nish mate-

rial. Refer to the appliance Installation Manual for more

detailed information.

1. Remove contents from packaging. Refer to Table 1 for

Decorative Front dimension information.

2. Install optional decorative trim kit, if desired, according

to instructions included with the kit.

Decorative Front Height Width

PORTRAIT-6-BK 32-7/16 39-5/16

PORTRAIT-8-BK 34-7/16 46-5/16

Table 1 Decorative Front Dimensions

Preparation Installation

1. Verify that the nishing strips have been removed, if

previously installed.

2. The decorative front is installed by engaging top and

bottom hooks on the front with top and bottom tabs on

the appliance. See Figure 7. Align the bottom hooks

on the decorative front with the bottom tabs on the

appliance. Set the bottom hooks on the tabs and tilt

the front toward the appliance until it contacts the top

tabs. Once the decorative front contacts the top tabs,

lift up slightly and push decorative front toward appli-

ance until hooks and tabs are engaged.

Figure 7 Hanging Tab and Hook Locations

TABS

(TOP AND BOTTOM)

HOOKS

(TOP AND BOTTOM)

Heat & Glo • Portrait Decorative Front Instructions • 2581-930 Rev. C • 8/22

Cleaning Instructions for Decorative fronts

Use a microber cloth and Windex® Original Glass

Cleaner or 03M003 Stove Bright® Glass Cleaner to

clean the decorative front immediately after installation

to remove acids deposited by the installer or technician.

Spray the cleaner onto the microber cloth and carefully

wipe the entire surface. The decorative front should

be cleaned in this manner annually by the homeowner

to remove ngerprints or other contaminants. Once

oxidation of the paint pigment has occurred, cleaning will

not restore the original color.

SERVICE PARTS

Decorative

Front

Part Number Description

PORTRAIT-6 SRV2595-031 Mesh

PORTRAIT-8 SRV2597-031 Mesh

PORTRAIT-6

PORTRIM6-BR Trim Kit, Antique Brass

PORTRIM6-CO Trim Kit, Antique Copper

PORTRIM6-NI Trim Kit, Antique Nickel

PORTRAIT-8

PORTRIM8-BR Trim Kit, Antique Brass

PORTRIM8-CO Trim Kit, Antique Copper

PORTRIM8-NI Trim Kit, Antique Nickel

Please contact your Hearth & Home Technologies

dealer with any questions or concerns.

For the location of your nearest Hearth & Home Technologies

dealer,

please visit www.hearthnhome.com.

Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044

www.hearthnhome.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kaminzubehör Handbücher

Heat & Glo

Heat & Glo 6KX-AU Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-I30FB Bedienungsanleitung

Heat & Glo

Heat & Glo TIARII-BK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO-II Series Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-6000GLX Bedienungsanleitung

Heat & Glo

Heat & Glo ARC-32 Handbuch

Heat & Glo

Heat & Glo 6000CMOD-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-Cerona42 Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-6000GL Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-I35 Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-SL750TRS-D Bedienungsanleitung

Heat & Glo

Heat & Glo COSMO32-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo Firescreen Bedienungsanleitung

Heat & Glo

Heat & Glo Tonic SLR-C Bedienungsanleitung

Heat & Glo

Heat & Glo DRIFTWOOD-C32 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000G Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO-II-48 Bedienungsanleitung

Heat & Glo

Heat & Glo VPK-DV Bedienungsanleitung

Heat & Glo

Heat & Glo GRL-850-AU Betriebsanleitung

Heat & Glo

Heat & Glo OGL-42 Handbuch

Heat & Glo

Heat & Glo SSF-LUX60-BK Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-I35FB Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-Cerona36 Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-SL550TRS-D Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung