Heat & Glo ST-HVBI-AU Bedienungsanleitung

Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

MODEL: ST-HVBI-AU

AUSTRALIAN GAS ASSOCIATION APPROVED

APPROVALNUMBER6027

THIS MANUAL MUST BE USED FOR INSTALLATIONAND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA • (952) 985-6000

INSTALLATION AND OPERATION

INSTRUCTIONS

THIS PRODUCT MAYBE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:

(UnitedStates)4593510,4686807, 4766876,4793322, 4811534,5000162,5016609,5076254,5113843,5191877,5218953,5263471,5328356, 5341794,5347983, 5429495,5452708, 5542407,5601073,

5613487,5647340,5688568, 5762062,5775408,5890485, 5931661,5941237,5947112,5996575,6006743,6019099,6048195,6053165,6145502,6170481,6237588,6296474,6374822,6413079,6439226,

6484712,6543698,6550687,6601579,6672860,6688302B2,6715724B2,6729551,6736133,6748940,6748942,D320652,D445174,D462436;(Canada)1297749,2195264,2225408;

(Australia)543790;586383;

(Mexico)97-0457;(NewZealand)200265;

orotherU.S.andforeignpatentspending.

2Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

IMPORTANT: Read all instructions carefully before starting installation.

Failureto followthese installation instructions may resultin apossible fire

hazardand willvoid thewarranty.Save thismanual forfuture reference.

MODEL ST-HVBI-AU

ISAUSTRALIAN GASASSOCIATION

APPROVED FOR NATURAL GAS OR

PROPANE AS A BALANCED FLUE

HEATER.

Refer to the appliance data plates for gas

consumptionsand pressures.

Installation of this appliance should only be

carriedoutbyanauthorizedpersonin accor-

dance with the manufacturer's instructions.

Applianceis tobe installedin fullcompliance

with the National Gas Installation Standard

AS5601,themanufacturer'sinstructions,and

any local authorities' requirements for gas,

electricaland buildingregulations.

Thisapplianceanditscomponentsaretested

and safe when installed in accordance with

thisInstallationManual.Reporttoyourdealer

anypartsdamaged inshipment,specifically

check glass condition. Read all instructions

beforestartinginstallationandfollowthesein-

structionscarefullyduringinstallationtoensure

maximumbenefit andsafety. Failure tofollow

themwill void yourwarranty andmaypresent

afire hazard.

TheHeat&Glowarrantywillbevoidedby,and

Heat& Glodisclaimsanyresponsibilityforthe

followingactions:

• Installationofanydamagedheater or flue

systemcomponent

• Modificationoftheheateror balancedflue

system installation other than as in-

structed by Heat&Glo.

• Improperpositioningofthegas logsorthe

glass door

• Installation and/or use of any component

partnotmanufacturedorapprovedbyHeat

&Glo,not withstanding any independent

testinglaboratory or other party approval

of such componentpartoraccessory.

PLEASE READ THIS MANUAL BEFORE INSTALLING AND

USING THIS APPLIANCE.

Heat & Glo Quality Systems

registeredby SGS ICS

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

20802Kensington Blvd.,Lakeville, MN55044, USA

Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

TABLE OF CONTENTS

1.0 INSTALLATION INSTRUCTIONS. ............................................................... 4

1.1 Locating theHeater .............................................................................. 5

1.2 FramingtheHeater .............................................................................. 6

1.3 FlueSystemApprovalsandInstallation ................................................. 9

1.4 ConnectingtheGasSupply ................................................................ 21

1.5 IgnitionSystem Wiring........................................................................ 21

1.6 BlowerWiring..................................................................................... 22

1.7 MantelClearances ............................................................................. 23

1.8 LogInstallation ................................................................................... 24

1.9 InstallerTesting ................................................................................... 27

2.0 OPERATING INSTRUCTIONS................................................................... 27

2.1 OperatingCautions ............................................................................ 28

2.2 SafetyandLightingInformation........................................................... 29

2.3 PowerOutage .................................................................................... 29

2.4 Fan Operation .................................................................................... 30

3.0 SERVICING AND MAINTENANCE. ........................................................... 30

3.1 Removalof CoversforServicing ........................................................ 31

3.2 Removalof ComponentsforService .................................................. 31

3.3 PartsReplacement............................................................................. 31

3.4 Adjustmentsand ReplacementParts .................................................. 31

3.5 Troubleshooting.................................................................................. 32

4.0 REPLACEMENT PARTS........................................................................... 35

LimitedWarranty.......................................................................................... 37

4Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

Figure 1. Diagram of ST-HVBI-AU

1.0 INSTALLATION INSTRUCTIONS

When planning a heater installation, it’s necessary to

determine:

•Where the unit is to be installed.

•Thevent systemconfiguration tobe used.

•Gas supply piping.

•Electrical supply wiring.

•Framingand finishing details.

•Whether optional accessories—devices such as wall

switch,or remotecontrol—are desired.

If the heater is to be installed on carpeting or tile, or on any

combustible material other than wood flooring, the heater

should be installed on a metal or wood panel that extends

thefull widthand depth of theheater.

32-1/2 in.

(816mm)

36-3/16 in.

(919.3mm)

2-1/4 in.

(58mm)

4-3/4 in.

(121mm)

4-1/2”

(114mm)

4-1/16”

(102mm)

34-3/4 in.

(882mm) 4-1/2”

(114mm)

2-9/16”

(64mm)

24 in.

(610m)

9-11/16”

(245mm)

17-15/16”

(456mm)

42”

(1067mm)

ELECTRICAL

ACCESS

GAS LINE

ACCESS

Ø8”

(202mm)

12”

(306mm) 46-5/8”

(1184mm)

Ø7-7/8”

(202mm)

12”

(306mm)

5-1/4”

(132mm) ½”

(13mm)

FLUE COLLAR

TOP STANDOFFS

FLUE

COLLAR

TOP

LOUVER

ACCESS

DOOR

GAS CONTROLS

& LABELS

GAS LINE

ACCESS ELECTRICAL

ACCESS

Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

The diagram below shows space and clearance require-

ments for locating a heater within a room.

Minimum Clearances

from the Heater to Combustible Materials

Figure 2. Heater Dimensions and Locations

Clearance Requirements

Thetop,back,andsidesoftheheateraredefinedby stand-

offs. The minimum clearance to a perpendicular wall

extending pastthe faceof theheater is 25 mm (1 inch). The

metal ends of the heater may NOT be recessed into

combustible construction.

For minimum clearances, see the direct flue termination

clearance diagrams on pages 6 and 7 in this manual.

Minimum Clearances

from the Flue Pipe to Combustible Materials

* Theclearancetotheceilingismeasuredfrom

the top of the unit, excluding the standoffs (see

Figures 1 and 2).

The distance from the unit to combustible construction is

to be measured from the unit outer wrap surface to the

combustible construction, NOT fromthe screwheads that

secure the unit together.

mm inches

Glass Sides or Ends 914............... 36

Floor 0 ................. 0

RearFlue 13 .............. 1/2

Metal Sides or Ends 13 .............. 1/2

Top 64 ............. 2 1/2

Ceiling* 787............... 31

mm Inches

Vertical Sections. ............ 25 ................ 1

Horizontal Sections

Top.................................... 75 ................ 3

Bottom .............................. 25 ................ 1

Sides ................................ 25 ................ 1

At Wall Firestops

Top.................................... 64 ............. 2 1/2

Bottom .............................. 13 ...............1/2

Sides ................................ 25 ................ 1

1.1 Locating the Heater

914 mm

GLASS

914 mm

6Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

Figure 3. Framing Dimensions

1.2 Framing the Heater

Framing can be built before or after the heater is set in

place.Framing should bepositioned to accommodatewall

coverings and heater facing material. The diagram below

showsframing reference dimensions.

CAUTION: MEASURE HEATER DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVERING

DETAILS,BEFOREFRAMINGCONSTRUCTIONBEGINS.

WARNING:FRAMING DIMENSIONS ASSUME

USE OF 1/2 INCH (12.7MM) (THICK WALL

COVERINGMATERIALS ON EXTERIOR OF FRAM-

INGONLYAND NO SHEETROCKONINTERIOROF

FRAMING.

A B C D E

1.21M(47-5/8 in.) 1.08 M(42-1/2in.) 584mm(23in.) 909mm(35-3/4 in.) 1.37M (54in.)

Shows center of 254mm x 305mm (10 in. x 12 in.) flue

framing holes for top and rear flueing. The center of

the hole is 25.4mm (one inch) above the center of the

horizontal flue pipe. Framing should be constructed of

51mm x 102mm (2 in. x 4 in.) lumber or heavier.

Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the

nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a flue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a flue terminal to a LP Gas

cylinder. A flue terminal is considered to be a source of ignition.

MINIMUMCLEARANCESREQUIRED FORBALANCEDFLUETERMINALS

ORTHEFLUETERMINALSOFOUTDOORAPPLIANCES

T = Flue terminal M = Gas meter Shading indicates prohibited

I = Mechanical air inlet P = Electricity meter areas for flue terminals

or fuse box

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances up to 50 MJ/h input ........................................................................................... 300

Appliances over 50 MJ/h input ............................................................................................ 500

b - From the ground or above a balcony...................................................................................... 300

c - From a return wall or external corner ..................................................................................... 500

d - From a gas meter (M) ...........................................................................................................1000

e - From an electricity meter or fuse box (P) ............................................................................... 500

f - From a drain or soil pipe......................................................................................................... 150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal ......................................................... 500

h - From any other flue terminal, cowl, or combustion air intake ............................................... 500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-floor ventilation:

Appliances up to 150 MJ/h input ......................................................................................... 500

Appliances over 150 MJ/h input ........................................................................................1500

k - From a mechanical air inlet, including a spa blower .........................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of

sub-floor ventilation.............................................................................................See table below

DOOR

OPENABLE

WINDOW

kSEE NOTE 2

SEE NOTE 3

CLEARANCES

Space Heaters AllotherAppliances

Up to 50 MJ/h

Input

150

Up to 50 MJ/h

Input

500

Over50MJ/hand

upto 150 MJ/h Input

1000

Over150 MJ/h

Input

1500

Figure 4.

8Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

NOTE: PIPES OVERLAP 32mm (1-1/4”)

AT EACH JOINT.

Figure 5. DVP-Series Direct Flue Component Specifications (127mm (5”) inner pipe / 203mm (8”) outer pipe)

DVP90ST

320mm

(12-9/16 in.)

286mm

(11-1/4 in.)

185mm

(7-1/4 in.)

32mm (1-1/4 in.) TYP

18mm

(1/2 in.) TYP

218mm

(8-9/16 in.)

DVP36

DVP48

1219mm

(48 in.)

610mm

(24 in.)

914mm

(36 in.)

102mm

(4 in.)

152mm

(6 in.)

DVP4

DVP6

305mm

(12 in.)

DVP12

51mm (2 in.)

MIN.

DVP12A

310mm

(12-3/16 in.)

MAX.

DVP24

251mm

(9-7/8 in.) 45.0

261mm

(10-1/4 in.)

DVP45

362mm

(14-1/4 in.)

Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

Figure 6. Flue System Components and Termination Kits

1.3 Flue Sytem Approvals and Installation

A. Flue System Approvals

These models are approved to use DVP series direct flue

pipe components and terminations (see Figures 5 and 6).

Approvedflue system componentsare labeled for identifi-

cation. This pipe is tested and listed as an approved com-

ponentof the heater.The pipeis tested tobe run inside an

enclosedwall.There is norequirementforinspection open-

ingsat eachjoint within the wall. There is norequired pitch

for horizontal flue runs. NO OTHER FLUEING SYSTEMS

OR COMPONENTS MAY BE USED.

Detailedinstallationinstructions are includedwitheach flue

termination kit and should be used in conjunction with this

InstallersGuide.

The flame and ember appearance may vary based on the

typeof fuel burned and the flueing configurationused.

Identifying Flue Components

The flue systems installed on this gas heater may include

one,two, orthree 90°elbow assemblies. The relationships

ofvertical rise to horizontal runin flue configurations using

90° elbows MUST BE strictly adhered to. The rise to run

relationshipsare shownin the flueing drawings andtables.

Referto the diagramson the nextseveral pages.

Thismodel hasa 450elbow included with it.It maybe posi-

tionedto flue eitherhorizontal or vertical.Depending on the

installation,decidewhich direction theelbowshould befac-

ing.Remove the 8 screws fromthe cornercover plate. Po-

sitionthe 450elbowas desiredand replacethe cornercov-

er plate with the 8 screws.

HORIZONTAL

TERMINATION

WALL FIRESTOP

90 DEGREE

ELBOW

PIPE LENGTH

CEILING

FIRESTOP

VERTICAL

TERMINATION STORM COLLAR

ROOF FLASHING

Terminations Kits

DVP-TVHW

DVP-TRAP

SERIES

10 Heat & Glo • ST-HVBI-AU • 2082-900 Rev. C • 8/06

Figure 7.

STRAIGHTOUT

HORIZONTALFLUEING

Max. Run

610 mm (24 in.)

Figure 8.

CAP

STRAIGHTUP

VERTICALFLUEING

V (FT.)

12.2M MAX. (40 FT.)

Andere Handbücher für ST-HVBI-AU

Inhaltsverzeichnis

Andere Heat & Glo Gasheizung Handbücher

Heat & Glo

Heat & Glo T-HVBI-AUB Bedienungsanleitung

Heat & Glo

Heat & Glo 350TRSI-AUF Bedienungsanleitung

Heat & Glo

Heat & Glo ST-HVBI-AU Bedienungsanleitung

Heat & Glo

Heat & Glo MEZZO 1000-AUB Bedienungsanleitung

Heat & Glo

Heat & Glo GRAND-I35 Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRS-IPI-E Bedienungsanleitung

Heat & Glo

Heat & Glo GRL-850-AU Bedienungsanleitung

Heat & Glo

Heat & Glo TIARAI-BK-C Bedienungsanleitung

Heat & Glo

Heat & Glo 6000XLSB Montageanleitung

Heat & Glo

Heat & Glo MISSION-BAY Bedienungsanleitung

Heat & Glo

Heat & Glo Heat & Glo TIARAII-BK-B Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung