Heat & Glo 6000TRSI-AUC Bedienungsanleitung

1Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

INSTALLATION AND OPERATION INSTRUCTIONS

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

MODEL: 6000TRSI-AUC

AUSTRALIAN GAS ASSOCIATION CERTIFIED

CERTIFICATE NUMBER 5668

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁreplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂammable materials.

• Keep clothing, furniture, draperies and other ﬂammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the

ﬁxed glass panel. DO NOT operate the appliance with the barrier removed.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

7571 215th Street West, Lakeville, MN 55044, USA, www.heatnglo.com

Thisproductiscoveredbyoneormoreofthefollowingpatents:(UnitedStates)5328356,5601073,5613487,5647340,5890485,5941237,

5947112,5996575,6006743,6019099,6053165,6145502,6170481,6374822,6484712, 6601579, 6769426, 6863064, 7077122,7098269,

7258116, 7470729 or other U.S. and foreign patents pending.



2Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

IMPORTANT: Read all instructions carefully before starting installation.

Failure to follow these installation instructions may result in a possible ﬁre

hazard and will void the warranty. Save this manual for future reference.

MODEL 6000TRSI-AUC

ISAUSTRALIANGASASSOCIATIONAPPROVED

FOR NATURAL GAS OR PROPANE AS A

BALANCED FLUE HEATER.

Refertothe appliancedataplates forgasconsump-

tions and pressures.

Installation of this appliance should only be carried

out by an authorized person in accordance with the

manufacturers instructions. All relevant codes and

regulations laid down by the gas ﬁtting authorities,

municipal building regulations, electrical wiring

regulations, and the requirements of the AGA Gas

Installation Code must be observed.

This appliance and its components are tested and

safewhen installedin accordance with this Installa-

tion Manual. Report to your dealer any parts dam-

agedinshipment, speciﬁcally check glasscondition.

The gas logs and ﬂue system components are in

separate packages.

PLEASE READ THIS MANUAL BEFORE INSTALLING AND

USING THIS APPLIANCE.

Readall instructionsbeforestarting installationand

followthese instructions carefullyduring installation

to ensure maximum beneﬁt and safety. Failure to

follow them will void your warranty and may pres-

ent a ﬁre hazard.

The Heat & Glo warranty will be voided by, and

Heat & Glo disclaims any responsibility for the fol-

lowing actions:

• Installation of any damaged heater or ﬂue sys-

tem component

• Modiﬁcation of the heater or balanced ﬂue sys-

tem installation other than as instructed by Heat

& Glo.

• Improperpositioning of thegas logs orthe glass

door

• Installation and/or use of any component part

not manufactured or approved by Heat & Glo,

not withstanding any independent testing

laboratory or other party approval of such com-

ponent part or accessory.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

7571 215th Street West, Lakeville, MN 55044

3Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

TABLE OF CONTENTS

1.0 INSTALLATION INSTRUCTIONS......................................................................4

A. Locating the Heater.....................................................................................5

B. Framing the Heater......................................................................................6

C. Flue System Approvals and Installations.....................................................8

D. Connecting the Gas Supply.........................................................................19

E. Ignition System Wiring.................................................................................20

F. Mantel Clearances.......................................................................................22

G. Log Placement.............................................................................................23

H. Installer Testing............................................................................................25

2.0 OPERATING INSTRUCTIONS. .........................................................................25

A. Safety and Lighting Information...................................................................27

B. Power Outage..............................................................................................28

C. Fan Operation..............................................................................................28

3.0 SERVICING AND MAINTENANCE. ..................................................................29

A. Removal of Covers for Servicing.................................................................30

B. Removal of Components for Service...........................................................30

C. Parts Replacement......................................................................................30

D. Adjustments and Replacement Parts..........................................................30

E. Troubleshooting...........................................................................................31

4.0 REPLACEMENT PARTS...................................................................................34

Limited Lifetime Warranty...................................................................................37

Vent Components Diagrams ..............................................................................39

4Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

Figure 1.1 Diagram of the 6000 Series

1.0 INSTALLATION INSTRUCTIONS

When planning a heater installation, it’s necessary to

determine:

• Where the unit is to be installed.

• The ﬂue system conﬁguration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and ﬁnishing details.

Ifthe heater is to be installed oncarpeting ortile, or on

anycombustible materialotherthan woodﬂooring, the

heater should be installed on a metal or wood panel

that extends the full width and depth of the heater.

FRONT VIEW

TOP VIEW

LEFT SIDE RIGHT SIDE

GAS LINE

ACCESS

Location Inches Millimeters

J 21.5 546

K 11-11/16 297

L 28-1/2 724

M 14-1/4 362

N 8-1/2 216

O 2-7/8 73

P 8-1/2 216

Q1 25

R 36-1/8 918

Location Inches Millimeters

A 41 1041

B 36-1/8 918

C 33-1/2 851

D 34-5/8 879

E 2-1/4 57

F 9-11/16 246

G 26-7/8 683

H 6 dia 152

I 40-1/8 1019

5Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

Clearance Requirements

The top, back, and sides of the heater are deﬁned by standoffs.

The minimum clearance to a perpendicular wall extending past the face of the heater is

one inch (25 mm).

For 6000 Series Models, the back of the heater may be recessed 21-1/2 inches (546 mm)

into combustible construction.

For minimum clearances, see the direct ﬂue termination clearance diagrams on page 7.

Minimum Clearances from the Heater to Combustible Materials

Glass

Front Floor Back of

Heater Sides of

Heater Top of

Heater Ceiling

36 inches

914 mm 01/2 inch

13 mm 1/2 inch

13 mm 3-1/2 inches

89 mm 31 inches

787 mm

Minimum Clearances from the Flue Pipe to Combustible Materials

For Horizontal Sections For Vertical

Sections At Wall Firestops

Top Bottom Sides Top Bottom Sides

3 inches

75 mm 1 inch

25 mm 1 inch

25 mm 2-1/2 inches

63.7 mm 1/2 inch

13 mm 1 inch

25 mm

REAR FLUE,

HORIZONTAL TERMINATION

TWO 90º ELBOWS REAR FLUE

NO ELBOWS

REAR FLUE

ONE 90º ELBOW

ALCOVE

INSTALLATION

TOP FLUE

ONE 90º ELBOW

NOTE: THE REAR STANDOFF MAY NEED

TO BE REMOVED WHEN VENTING AT 45º

1,3 cm

ABCD E F G H I

6000 in. 51 42 72 56-5/8 See Section F.

Mantel Projections 22 17-3/4 8 28-3/4

mm 1295 1067 1829 1438 559 451 203 730

A. Locating the Heater

Figure 1.2

6Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

Framing should be constructed

of 2 X 4 lumber or heavier.

A B C D * E *

42-1/8 in. 40-1/4 in. 22-1/16 in. 26-7/8 in. 48 in.

(1070 mm) (1022 mm) (560 mm) (684 mm) (1219 mm)

Figure 1.3 Framing Dimensions

B. Framing the Heater

Framing can be built before or after the heater is set in

place. Framing should be positioned to accommodate

wallcoveringsand heaterfacingmaterial.The diagram

below shows framing reference dimensions.

*NOTE:These dimensionsshow the center

of the horizontal ﬂue pipe. The center of

the framing hole is one inch (25.4 mm)

above the center of the ﬂue pipe.

140 mm

76 mm

NON-COMBUSTIBLE ZONE

IS DEFINED BY 76MM ABOVE

THE ELBOW FOR THE ENTIRE

WIDTH AND DEPTH (BEHIND

THE FRONT HEADER) OF

THE FIREBOX.

WALL

STUD

CAUTION: MEASURE HEATER DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVER-

ING DETAILS, BEFOREFRAMING CONSTRUCTION

BEGINS.

7Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a ﬂue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a ﬂue

terminal to a LP Gas cylinder. A ﬂue terminal is considered to be a source of ignition.

MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS

OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES

Figure 1.4

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances up to 50 MJ/h input..............................................................................................300

Appliances over 50 MJ/h input...............................................................................................500

b - From the ground or above a balcony.........................................................................................300

c - From a return wall or external corner.........................................................................................500

d - From a gas meter (M)..............................................................................................................1000

e - From an electricity meter or fuse box (P)...................................................................................500

f - From a drain or soil pipe............................................................................................................150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal...............................................................500

h - From any other ﬂue terminal, cowl, or combustion air intake ....................................................500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-ﬂoor ventilation:

Appliances up to 150 MJ/h input............................................................................................500

Appliances over 150 MJ/h input...........................................................................................1500

k - From a mechanical air inlet, including a spa blower...............................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of...................................... See table

sub-ﬂoor ventilation................................................................................................................ below

T= Flue terminal M= Gas meter Shading indicates prohibited

I= Mechanical air inlet P= Electricity meter or fuse box areas for ﬂue terminals

openable

window

door

kdb

See note 2

See note 3

CLEARANCE 'n' (mm)

Space Heaters All other appliances

Up to 50 MJ/h input Up to 50 MJ/h input Over 50 MJ/h input and

Up to 150 MJ/h input Over 50 MJ/h input

150 500 1000 1500

8Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

TABLE 1

Figure 1.5. Flue Components and Terminations

MODEL

6TRSI-AUE

FLUE TERMINATION APPROVALS

DVP-TRAP2 HORIZONTAL TERMINATION CAP

DVP-TVHW VERTICALTERMINATION CAP

C. Flue System Approvals And Installations

Thesemodels haveﬂuestarting collarsonboth thetop

and the back of the unit. Depending upon the instal-

lation, decide which ONE set of starting collars will be

usedto attachthe ﬂuesystem.Thestarting collarseal-

ing cap must remain on the starting collar NOT used.

These models use DVP series direct ﬂue components

whenusing theTOP ﬂuecollars andDVP-series direct

ﬂue components when using the REAR ﬂue collars.

Approved ﬂue system components are labeled for

identiﬁcation. NO OTHER FLUEING SYSTEMS OR

COMPONENTS MAY BE USED. Detailed installation

instructions are included with each ﬂue termination kit

and should be used in conjunction with this manual.

Figure 5 below shows ﬂue system components and

terminations.

Identifying Flue Components

The ﬂue systems installed on this gas heater may

include one, two, or three 90°elbow assemblies. The

relationships of vertical rise to horizontal run in ﬂue

configurations using 90° elbows MUST BE strictly

adheredto.Theriseto runrelationshipsareshowninthe

ﬂueing drawings and tables on the next few pages.

WARNING: THIS GAS APPLIANCE AND FLUE AS-

SEMBLY MUST FLUE DIRECTLY TO THE OUTSIDE

AND MUST NEVER BEATTACHED TOA CHIMNEY

SERVING A SEPARATE SOLID FUEL BURNING

APPLIANCE. EACH GAS APPLIANCE MUST USE

ASEPARATE FLUE SYSTEM-COMMON FLUE SYS-

TEMS ARE PROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD COM-

BUSTIBLE MATERIALBE CLOSER THAN76 mmAT

WALL FIRE-STOPS FROM THE TOP OF THE PIPE

OR 25 mm TO THE SIDESAND THE BOTTOM FOR

HORIZONTAL SECTIONS OF THIS FLUE SYSTEM.

VERTICAL SECTIONS OF THIS SYSTEM REQUIRE

AMINIMUM OF 25 mm CLEARANCE TO COMBUS-

TIBLE MATERIALS ALL AROUND THE PIPE.

For alternative installations, other than depicted, con-

tact your dealer for further information.

Refer to Figure 1.5 for required clearances to ﬂue

terminals.

HORIZONTAL

TERMINATION

WALL FIRESTOP

90 DEGREE

ELBOW

VERTICAL

TERMINATION STORM COLLAR

ROOF FLASHING

HORIZONTAL PIPE

SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING

FIRESTOP

DVP-SERIES

DVP-TRAP2

DVP-TVHW

Flue system termination kits

9Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

This model is approved to use DVP-Series ﬂue pipe

components.ADVP-TRAP2TerminationCapmustbe

usedtoterminateﬂuesystemsinahorizontalposition.

A DVP-TVHW vertical Termination Cap must be used

to terminate ﬂue systems in a vertical position.

Figures 1.8 through 1.15 show the flue systems

approved for these models. Approved ﬂue system

componentsare labeled foridentiﬁcation. NO OTHER

FLUESYSTEMSOR COMPONENTS MAY BE USED.

Detailedinstallationinstructions areincludedwith each

ﬂue termination kit and should be used in conjunction

with this manual.

WARNING: THIS GAS APPLIANCE AND FLUE

ASSEMBLY MUST BE FLUED DIRECTLY TO THE

OUTSIDE AND MUST NEVER BE ATTACHED TO

A CHIMNEY SERVING A SEPARATE SOLID FUEL

BURNING APPLIANCE. EACH GAS APPLIANCE

MUST USE ASEPARATE FLUE SYSTEM-COMMON

FLUE SYSTEMS ARE PROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD COM-

BUSTIBLEMATERIAL BECLOSERTHAN 3INCHES

(2-1/2 INCHES AT WALL FIRESTOPS) FROM THE

TOP OF THE8 INCH PIPEOR 1 INCH TOTHE SIDES

AND THE BOTTOM FOR HORIZONTAL SECTIONS

OF THIS FLUE SYSTEM. VERTICAL SECTIONS OF

THIS SYSTEM REQUIRE A MINIMUM OF 1 INCH

CLEARANCE TO COMBUSTIBLE MATERIALS ALL

AROUND THE 8 INCH PIPE.

For alternative installations, other than depicted, con-

tact your dealer for further information.

Refer to Figure 1.5 for required clearances to ﬂue

terminals.

MODEL FLUE TERMINATION APPROVALS

6000TRSI-AUC DVP-TRAP2, DVP-TVHW

TABLE 1

Figure 1.6

VERTICAL FLUE RESTRICTOR

If the heater installation requires a vertical ﬂue ex-

ceeding 4.5 m above the unit with no horizontal ﬂue

or elbows a vertical ﬂue restrictor must be installed

(see Figure 1.6).

Figure 1.7

CAP

MAX. RUN

36 FT.

(10.97m)

STRAIGHT UP VERTICAL FLUE SYSTEM

Figure 1.6 shows straight up vertical ﬂue system ap-

proved for use on this model.

RESTRICTOR

PLATE

10 Heat & Glo • 6000TRSI-AUC • 2078-900 Rev. Q • 6/10

Figure 1.8 Straight Out Horizontal Flueing

H H

MIN. RUN MAX. RUN

13.1" (331 mm) 24" (610 mm)

Figure 1.9 Flueing with One 90° Elbow

V H

1´ MIN. (0.30 M) 2´ MAX. (0.61 M)

2´ MIN. (0.61 M) 4´ MAX. (1.22 M)

3´ MIN. (0.91 M) 6´ MAX. (1.83 M)

4´ MIN. (1.22 M) 8´ MAX. (2.44 M)

24´ MAX. (7.32 M) 8´ MAX. (2.44 M)

ONE (1) 90-DEGREE ELBOW

Figures1.9 and1.10show aninstallation usingone(1)

90-degree elbow. Dimension V is listed as MINIMUM

vertical dimensions and dimension H is listed as cor-

responding MAXIMUM horizontal dimensions.

TWO (2) 90-DEGREE ELBOWS

Figures 1.11 and 1.12 show examples of possible in-

stallationsusing two(2) 90-degreeelbows. Dimension

Vislisted asMINIMUM verticaldimensions, dimension

H is listed as MAXIMUM beginning horizontal dimen-

sions,and dimensionH +H1is listedas corresponding

TOTAL MAXIMUM horizontal dimensions.

THREE (3) 90-DEGREE ELBOWS

Figures 1.13 through 1.15 show examples of possible

installationsusing three(3) 90-degreeelbows. Dimen-

sions V are listed MINIMUM ﬁrst vertical dimensions

and dimensions H are listed as beginning MAXIMUM

horizontal dimensions. Dimensions H + H1and H +

H1 + H2are listed as TOTAL MAXIMUM horizontal

dimensions. Dimensions V + V1are listed as TOTAL

MAXIMUM vertical dimensions.

ELBOWS

Theﬂue systems installedon thisgas heater mayalso

include one (1), two (2), or three (3) 90 - degree elbow

assemblies.

Figures 1.9 through 1.15 and their corresponding

tables show examples of ﬂue conﬁgurations using

elbows. The relationships of vertical rise to horizontal

runinﬂueconﬁgurationsusingelbowsMUSTbestrictly

adhered to.

STRAIGHT OUT HORIZONTAL FLUE SYSTEM

Figure 1.8 shows straight out horizontal ﬂue systems

approved for use on this model.

Andere Handbücher für 6000TRSI-AUC

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo I25X-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IPI-S Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550TM-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo RHW-51 Bedienungsanleitung

Heat & Glo

Heat & Glo LCOR-HVB-CE Montageanleitung

Heat & Glo

Heat & Glo SL-550BE-M-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo CERONA-36 Bedienungsanleitung

Heat & Glo

Heat & Glo ST-36TR-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GCF-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GCF-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TR-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo 8000CF-OAK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo RED40-N-AU Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36C Bedienungsanleitung

Heat & Glo

Heat & Glo SL350TRSI-N-CE Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550TR-IPI-E Bedienungsanleitung

Heat & Glo

Heat & Glo SL-750TRSFHHIPI Bedienungsanleitung

Heat & Glo

Heat & Glo TIARAP-AL Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5 Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550TM-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo CF230E-B Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-48D Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO48-CF Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch