Heat & Glo 8000TRC Montageanleitung

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

-What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Heat-N-Glo Fireplace

Model:

8000TRC Installers Guide

WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SER-

VICE OR MAINTENANCE CAN CAUSE

INJURY OR PROPERTY DAMAGE.

REFER TO THIS MANUAL. FORASSIS-

TANCE OR ADDITIONAL INFORMA-

TION CONSULT A QUALIFIED IN-

STALLER, SERVICE AGENCY, OR THE

GAS SUPPLIER.

Underwriters

Laboratories Listed

582-900-A 6/99

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THISAPPLIANCE. THIS

INSTALLERS GUIDE

MUST BE LEFT WITH

THE APPLIANCE FOR FUTURE REFERENCE.

1. This appliance may be installed in an

aftermarket,permanentlylocated,

manufactured (mobile) home, where

not prohibited by local codes.

2.This appliance is only for use with the

type of gas indicated on the rating

plate. This appliance is not convertible

for use with other gases, unless a

certified kit is used.

Please contact your Heat-N-Glo dealer for any

questions or concerns. For the number of your nearest

Heat-N-Glo dealer, please call 612-985-6000.

Heat-N-Glo, a division of HearthTechnologies Inc.

20802KensingtonBoulevard,Lakeville,MN55044

WARNING: IF THE

INFORMATION IN THESE

INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE

OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)

543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

SAFETY AND WARNING INFORMATION

READ

and

UNDERSTAND

all instructions carefully before starting the installation.

FAILURE TO FOLLOW

these installation instructions may result in a possible fire

hazard and will void the warranty.

Prior to the first firing of the fireplace,

READ

the Using Your Fireplace section of the

Owners Guide

DO NOT USE

this appliance if any part has been under water. Immediately

CALL

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be

PERFORMED

by a qualified service person. The

appliance and venting system should be

INSPECTED

before initial use and at least

annually by a professional service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc. It is

IMPERATIVE

that the unit’s

control compartment, burners, and circulating air passageways

BE KEPT CLEAN

provide for adequate combustion and ventilation air.

Always

KEEP

the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT

the flow of combustion and ventilation air. Keep the front of the

appliance

CLEAR

of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be

LOCATED

out of traffic areas and

away from furniture and draperies. Clothing or flammable material

SHOULD NOT BE

PLACED

on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature and

should STAY AWAY to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units

MUST

use one of the vent systems described in the Installing the Fireplace

section of the

Installers Guide

NO OTHER

vent systems or components

MAY BE USED

This gas fireplace and vent assembly

MUST

be vented directly to the outside and

MUST

NEVER

be attached to a chimney serving a separate solid fuel burning appliance. Each

gas appliance

MUST USE

a separate vent system. Common vent systems are

PROHIBITED

INSPECT

the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly

MUST

be in place and sealed, and the trim door assembly

MUST

be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE

this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person.

DO NOT

strike or slam the glass door.

The glass door assembly

SHALL ONLY

be replaced as a complete unit, as supplied by

the gas fireplace manufacturer.

NO SUBSTITUTE

material may be used.

DO NOT USE

abrasive cleaners on the glass door assembly.

DO NOT ATTEMPT

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating

season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

Table of

Contents

Safety and Warning Information .......................... i

Section 1: Approvals and Codes ...................... 1

Approval Listings and Codes ................................. 1

Appliance Certification............................................ 1

Installation Codes ................................................... 1

High Altitude Installations ........................................ 1

Section 2: Getting Started ................................ 2

Introducing the Heat-N-Glo Gas Fireplaces............ 2

Pre-installation Preparation .................................... 2

Section 3: Installing the Fireplace .................... 4

Step 1 Locating the Fireplace ........................ 4

Step 2 Framing the Fireplace ........................ 5

Step 3 Installing the Vent System .................. 6

A. Vent System Approvals .................. 6

B. Installing Vent Components.......... 17

C. Vent Termination .......................... 23

Step 4 Positioning, Leveling, and

Securing the Fireplace ..................... 28

Step 5 The Gas Control Systems ................ 28

Step 6 The Gas Supply Line ........................ 29

Step 7 Gas Pressure Requirements ........... 30

Step 8 Wiring the Fireplace ......................... 31

Step 9 Finishing ........................................... 33

Step 10 Installing Trim, Logs, and

Ember Material ................................. 34

Installing the Trim ............................. 34

Positioning the Logs ......................... 35

Placing the Ember Material .............. 35

Step 11 Before Lighting the Fireplace ............ 37

Step 12 Lighting the Fireplace ....................... 37

After the Installation ....................................... 37

Section 4: Maintaining and Servicing

Your Fireplace ................................ 38

Section 5: Replacement Parts

and Accessories ............................. 40

Replacement Parts .............................................. 40

Accessories ......................................................... 45

i i

Approval Listings

and Codes

Appliance Certification

The Heat-N-Glo fireplace model discussed in this

Installers Guide has been tested to certification

standards and listed by the applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

8000TRC Underwriters Direct Vent ANSI Z21.50 CGA2.22/IR#41

Laboratories Gas Fireplace

Installation Codes

The fireplace installation must conform to local codes. Before installing the

fireplace, consult the local building code agency to ensure that you are in

compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the

National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-

B149 Installation Codes (in Canada). The appliance must be electrically

grounded in accordance with local codes or, in the absence of local codes with

the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the

CSA C22.1Canadian Electric Code (in Canada).

This model may be installed in a bedroom or bed-sitting room in the U.S.A. and

Canada.

High Altitude Installations

U.L. Listed gas fireplaces are tested and approved for elevations from 0 to 2,000

feet in the U.S.A. and from 0 to 4,500 feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United

States), it may be necessary to decrease the input rating by changing the

existing burner orifice to a smaller size. Input should be reduced four percent

(4%) for each 1,000 feet above sea level, unless the heating value of the gas has

been reduced, in which case this general rule will not apply. To identify the proper

orifice size, check with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in

Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada), check

with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for

your location.

Approvals

and Codes

Getting

Started

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-install

Preparation

Heat-N-Glo direct vent gas fireplaces are designed to

operate with all combustion air siphoned from outside

of the building and all exhaust gases expelled to the

outside.

The information contained in this Installers Guide,

unless noted otherwise, applies to all models and gas

control systems.

Gas fireplace diagrams, including the dimensions,

are shown in this section.

This gas fireplace and its components are tested

and safe when installed in accordance with this

Installers Guide. Report to your dealer any parts

damaged in shipment, particularly the condition of

the glass. Do not install any unit with damaged,

incomplete, or substitute parts.

The vent system components are shipped in

separate packages. The gas logs may be

packaged separately and must be field installed.

Read all of the instructions before starting

the installation. Follow these instructions

carefully during the installation to ensure

maximum safety and benefit. Failure to follow

these instructions will void the owners

warranty and may present a fire hazard.

Figure 1. Diagram of the 8000TRC

The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims any

responsibility for, the following actions:

 Installation of any damaged fireplace or vent system component.

 Modification of the fireplace or direct vent system.

 Installation other than as instructed by Heat-N-Glo.

 Improper positioning of the gas logs or the glass door.

 Installation and/or use of any component part not manufactured and approved by

Heat-N-Glo, not withstanding any independent testing laboratory or other party

approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, its necessary to determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessoriesdevices such as a fan, wall switch, or remote

controlare desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible

material other than wood flooring, the fireplace should be installed on a metal or

wood panel that extends the full width and depth of the fireplace.

Installing the

Fireplace

Step 1

Locating the

Fireplace

The diagram below shows space and clearance

requirements for locating a fireplace within a room.

MODEL A B C D E

8000TRC 49 22 39 1/2 56 79

NOTE: DIMENSIONS SHOWN IN INCHES.

Figure 2. Fireplace Dimensions, Locations, and

Space Requirements

Clearance Requirements

The top, back, and sides of the fireplace are defined

by stand-offs.

Minimum Clearances from the Fireplace to

Combustible Materials

Glass Rear of Sides of Top of

Front Floor Fireplace Fireplace Fireplace Ceiling

36 inches 0 1/2 inch 1/2 inch 3-1/2 inches 31 inches

(914 mm) (13 mm) (13 mm) (89 mm) (787 mm)

The minimum clearance to a perpendicular wall

extending

past the face of the fireplace is one inch

(25 mm).

The back of the fireplace may be recessed 21 1/2

inches (546 mm) into combustible construction.

Minimum Clearances from the Vent Pipe to

Combustible Materials

For Vertical

For Horizontal Sections Sections At Wall Firestops

Top Bottom Sides Top Bottom Sides

3 inches 1 inch 1 inch 1 inch 2-1/2 inches 1/2 inch 1 inch

(75 mm) (25 mm) (25 mm) (25 mm) (63.7 mm) (13 mm) (25 mm)

For minimum clearances, see the direct vent

termination clearance diagrams on pages 25 and 27 in

this manual.

Step 2

Framing the

Fireplace

Fireplace framing can be built before or after the

fireplace is set in place. Framing should be positioned

to accommodate wall coverings and fireplace facing

material. The diagram below shows framing reference

dimensions.

CAUTION MEASURE FIREPLACE DIMENSIONS, AND

VERIFY FRAMING METHODS AND WALL

COVERING DETAILS BEFORE FRAMING

CONSTRUCTION BEGINS.

Framing should be

constructed of 2 X 4

lumber or heavier.

Models A B C D E

8000TRC 49 40 1/2 22 44 27 1/2

NOTE: DIMENSIONS SHOWN IN INCHES

Figure 3. Framing Dimensions

Vent system

termination kits

Vent system components

Figure 4. Vent Components and Terminations

Step 3

Installing the

Vent System

A. Vent System Approvals

This model is approved to use D-series direct vent

pipe components and terminations. Approved vent

system components are labeled for identification. This

pipe is tested and listed as an approved component

of the fireplace. The pipe is tested to be run inside an

enclosed wall. There is no requirement for inspec-

tion openings at each joint within the wall. There is no

required pitch for horizontal vent runs. NO OTHER

VENTING SYSTEMS OR COMPONENTS MAY BE

USED.

Detailed installation instructions are included with

each vent termination kit and should be used in con-

junction with this Installers Guide. The drawing below

shows vent system components and terminations.

The flame and ember appearance may vary based

on the type of fuel burned and the venting configura-

tion used.

Identifying Vent Components

The vent systems installed on this gas fireplace may

include one, two, or three 90°elbow assemblies. The

relationships of vertical rise to horizontal run in vent

configurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown

in the venting drawings and tables. Refer to the dia-

grams on the next several pages.

DV-90D

65/32

57/873/8

DV-45D

67/16

11 1/16 61/2

85/8

81/2

51/16

8/12 11 5/8

85/8

11 15/16

DV-36D

35 3/4

47 3/4

DV-48D

5 3/4

8 3/4

11 3/4

DV-12D DV-09D DV-06D

6-5/32"

(156 mm)

7-3/8" 5-7/8"

(187 mm) (149 mm)

8-1/2"

(216 mm)

8-5/8"

(220 mm)

11-15/16"

(303 mm)

11-5/8"

(295 mm) 11-1/16"

(281 mm) 6-1/2"

(165 mm)

8-5/8"

(220 mm)

5-1/16"

(129 mm)

8-1/2"

(216 mm)

6-7/16"

(164 mm)

35-3/4"

(908 mm)

47-3/4"

(1.2 m)

11-3/4"

(298 mm) 8-3/4"

(222 mm) 5-3/4"

(146 mm)

NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93 mm) AT EACH JOINT.

Figure 5. D-Series Direct Vent Component Specifications

(5-inch inner pipe / 8 5/8-inch outer pipe)

NOTE: TWO 45° ELBOWS MAY BE USED IN

PLACE OF ONE 90° ELBOW. RISE TO RUN RA-

TIOS IN THE VENT SYSTEM MUST BE FOLLOWED

IF 45° ELBOWS ARE USED.

This model has vent starting collars on both the top

and the back of the unit. Depending upon the installa-

tion, decide which ONE set of starting collars will be

used to attach the vent system. The starting collar

sealing cap must remain on the starting collar NOT

used.

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo 350TSI-P-CEM Sicherheitsleitfaden

Heat & Glo

Heat & Glo GATEWAY Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-I35-C Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550METRO-BU Bedienungsanleitung

Heat & Glo

Heat & Glo GRL-700-AU Bedienungsanleitung

Heat & Glo

Heat & Glo 6000BEC-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CLX-IFT-S Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TV-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo Everest Bedienungsanleitung

Heat & Glo

Heat & Glo SL350TRSI-N-CE Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GBV Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TV-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5F-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo Gas Fireplace SOULSTICE Bedienungsanleitung

Heat & Glo

Heat & Glo SOLARIS36-ST Bedienungsanleitung

Heat & Glo

Heat & Glo RUTHERFORD-50 Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace RH-36 Series Bedienungsanleitung

Heat & Glo

Heat & Glo ST-36TR-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SUPREME-N-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5 Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo CERONA-36 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRSI-AUC Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch