Heat & Glo SL-350TRSI-AUE Bedienungsanleitung

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

MODEL: SL-350TRSI-AUE

AUSTRALIAN GAS ASSOCIATION APPROVED

ApprovalNumber 5666

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044 USA

www.heatnglo.com

INSTALLATION AND OPERATION

INSTRUCTIONS

THIS PRODUCT MAYBE COVERED BY ONE OR MORE OFTHE FOLLOWING PATENTS:

(UnitedStates)4593510,4686807,4766876,4793322, 4811534,5000162, 5016609,5076254,5113843,5191877,5218953,5263471,5328356,5341794,5347983, 5429495,5452708,5542407,

5601073,5613487, 5647340,5688568, 5762062,5775408, 5890485,5931661, 5941237,5947112,5996575, 6006743,6019099, 6048195,6053165, 6145502,6170481,6237588, 6296474,

6374822,6413079,6439226,6484712,6543698,6550687,6601579, 6672860,6688302B2,6715724B2,6729551,6736133,6748940,6748942,D320652,D445174,D462436;(Canada) 1297749,

2195264,2225408;

(Australia)543790;586383;(Mexico)97-0457;(NewZealand)200265;

orotherU.S. andforeignpatentspending.

2Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

IMPORTANT: Read all instructions carefully before starting installation.

Failuretofollowtheseinstallationinstructions may result ina possible fire

hazard and will void the warranty. Save this Manual for future reference.

MODEL SL-350TRSI-AUE

ISAUSTRALIAN GASASSOCIATION

APPROVED FOR NATURAL GAS OR

PROPANE AS A BALANCED FLUE

HEATER.

Refer to the appliance data plates for gas

consumptionsand pressures.

Installationof thisappliance shouldonly be

carried out by an authorized person in ac-

cordance with the manufacturer's instruc-

tions. Applianceistobeinstalledinfullcom-

pliance with the National Gas Installation

Standard AS5601, the manufacturer's in-

structions,andanylocalauthorities'require-

mentsforgas, electricaland buildingregu-

lations.

This appliance and its components are

tested and safe when installed in accor-

dancewiththisInstallationManual. Report

to your dealer any parts damaged in ship-

ment,specificallycheckglasscondition.The

gas logs and flue system components are

inseparatepackages. Readall instructions

beforestarting installationandfollowthese

instructions carefully during installation to

ensure maximum benefit and safety. Fail-

uretofollowthemwillvoidyourwarrantyand

maypresent afire hazard.

TheHeat& Glo,a brandofHearth &Home

TechnologiesInc.warrantywillbevoidedby,

and Heat & Glo, a brand of Hearth & Home

TechnologiesInc.disclaimsanyresponsibil-

ityfor thefollowing actions:

• Installation of any damaged heater or

fluesystemcomponent

• Modification of the heater or balanced

flue system installation other than as

instructed by Heat & Glo, a brand of

Hearth& HomeTechnologiesInc.

• Improper positioning of the gas logs or

theglassdoor

• Installationand/oruseofanycomponent

part not manufactured or approved by

Heat & Glo, brand of Hearth & Home

TechnologiesInc.,not withstanding any

independent testinglaboratory or other

party approval of such componentpart

oraccessory.

PLEASEREADTHISMANUALBEFOREINSTALLING

ANDUSINGTHISAPPLIANCE.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA

Heat & Glo Quality Systems

registered by SGS ICS

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

TABLE OF CONTENTS

1.0 InstallationInstructions.........................................................................................5

1.1 Introduction...................................................................................................6

1.2 FlueSystemApprovalsandInstallation .........................................................8

1.3 Connectingthe GasSupply ........................................................................22

1.4 IgnitionSystem Wiring ................................................................................23

1.5 BlowerFan.................................................................................................24

1.6 Finishing ....................................................................................................25

1.7 InstallerTesting ...........................................................................................26

1.8 LogPlacement ...........................................................................................27

2.0 OperatingInstructions .......................................................................................30

2.1 Safetyand LightingInformation...................................................................31

2.2 Fan Operation ............................................................................................32

3.0 Servicingand Maintenance...............................................................................32

3.1 Removal ofCovers forServicing ................................................................33

3.2 Removal ofComponents forService ..........................................................33

3.3 PartsReplacement.....................................................................................33

3.4 Adjustmentsand ReplacementParts ..........................................................33

3.5 Troubleshooting..........................................................................................34

4.0 ReplacementParts ...........................................................................................35

LimitedWarranty...............................................................................................37

4Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

Figure 1. Diagram of SL-350TRSI-AUE

22-3/4 in.

(577mm)

11-3/8 in.

(289mm)

16-3/8 in.

(414mm)

8-3/4 in.

(223mm)

15-7/8 in.

(402 mm)

Ø6-5/8 in.

(167mm)

24 in.

(610mm)

5-5/8 in.

(144mm)

GAS LINE

ACCESS

41-3/4 in.

(1060mm)

21-3/8 in.

(542mm) 2-1/8 in.

(55mm)

30 in.

(764mm)

28-1/8 in.

(714mm)

33 in.

(837mm)

15-1/8 in.

(384mm) 3-1/2 in.

(90mm)

6-7/8 in.

(175mm)

ELECTRICAL

ACCESS

Ø8 in.

(203mm)

30-5/8 in.

(777mm)

FLUE COLLAR

COVER PLATE

TOP STANDOFFS

HOOD

RATING PLATE/LABELS

( BEHIND DOOR)

GAS

CONTROLS

( BEHIND DOOR)

GAS

ACCESS

BOTTOM

ACCESS DOOR

ELECTRICAL

ACCESS

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

Figure 2. Fireplace Dimensions, Locations, and

Space Requirements

1.0 INSTALLATION INSTRUCTIONS

Clearance Requirements

Thetop and back of fireplace aredefined bystand-offs.

Theheat shield must beattached as shown ifcombus-

tiblematerials areplaced directlyon top standoffs (Fig-

ure3).

The minimum clearance to a perpendicular wall ex-

tending past the face of the fireplace is 25mm.

Theback ofthe fireplacesmay be recessedinto com-

bustibleconstruction, asshown above.

Figure 3. Heat Shield

TOP

STANDOFFS

INSTALLED

HEAT SHIELD

Inplanning theinstallation forthe heater it is necessary

to determine where the unit is to be installed, the type

of flue system to be used (straight out, corner, or el-

evated),and whetheroptional accessories (wallswitch

orremotecontrol)are desired. Gassupply pipingshould

also be planned. Refer to the appliance data plate on

the base pan of the heater for all gas pressures and

inputrate information.

Theheater canbe mountedon anyof thefollowing sur-

face:

1. Aflat surface (minimum6mm base).

2. Four(4) cornersupports.

(Example: Four (4) concrete masonry blocks). These

supportsmust be positioned so theycontact all four(4)

perimeter edges on the bottom of the unit.

Heaterframing can bebuilt beforeor after theheater is

set in place. Framing should be positioned to accom-

modate wall covering and heater facing material. The

heater framing should be constructed of 2" X 4" (51 x

102mm) lumber or heavier. The framing headers may

reston the heater standoffs.Refer to Figure 2 and Fig-

ure4 forheater andframing reference dimensions.

NOTE: Notintended forfireplace insert.

Top Flue

A B C D E

Millimeter 837 413 728 1001 1416

A B C D E

Millimeter 837 413 843 1192 1686

1 in. MIN. (25mm)

Rear Flue

1in. Min. (25mm)

½ in. Min (13mm)

6Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

Figure 4. Framing Dimensions

Framing should be constructed

of 2 X 4 lumber or heavier.

The framing headers

may rest on the

fireplace stand-offs.

ABCD*E*

34" 30-5/8" 16 1/2" 41-3/4" 21-1/4"

(864mm) ( 778mm) (419mm) (1060mm) (540mm)

*NOTE: The center of the framing hole

is one inch (254mm) above the

center of the horizontal flue pipe.

CAUTION: Measure heater dimensions, and verify

framingmethodsand wallcovering details beforefram-

ingconstruction begins.

1.1 INTRODUCTION

This model is designed to operate with all combus-

tion air being siphoned from the outside of the build-

ing and all exhaust gases expelled to the outside of

the building.

WARNING: THIS UNIT IS NOT FOR USE WITH

SOLID FUEL.

These units MUST use the flue termination described

in the flueing section of the manual.

Thecontrol system forthis model isan electronic igni-

tiontype.Itconsistsofagascontrolvalve/variableregu-

lator, a pilot/sensor/electrode andan ON/OFF switch.

The controls are located behind the access door. Ro-

tate the door down to open. See Figure 1.

Minimum inlet gas supply pressure for purpose of in-

putadjustment is 4.5inches w.c. (1.13kPa) fornatural

gas and 11 inches w.c. (2.75kPa) for propane. Mani-

fold(outlet) pressures shouldbe set at3.5 inches w.c.

(.8kPa) for natural gas models and 9.5 inches w.c.

(2.36kPa)for propanemodels.

Minimum Clearances

from the Fireplace to Combustible Materials

Inches mm

Glass Front......................................36 ........ 914

Floor .................................................0........... 0

Rear ................................................ 1/2 ........ 13

Sides .............................................. 1/2 ........ 13

Top ................................................1 1/2 ....... 38

Ceiling* ............................................31........ 787

*The clearance to ceiling is measured from the top

of the unit, excluding the standoffs (see Figure 34). For minimum clearances, see the direct vent termina-

tion clearance in Figure 5.

Minimum Clearances

from the Vent Pipe to Combustible Materials

Inches mm

Vertical Sections. ............. 1 ................ 25

Horizontal Sections

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

At Wall Firestops

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a flue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a flue

terminal to a LP Gas cylinder. A flue terminal is considered to be a source of ignition.

MINIMUMCLEARANCESREQUIREDFORBALANCED FLUE TERMINALS

ORTHEFLUETERMINALSOFOUTDOOR APPLIANCES

Figure 5.

CLEARANCES 'n' (mm)

Space heaters All other appliances

Up to 50 MJ/h

input UP to 50 MJ/h

input Over 50 MJ/h &

to 150 MJ/h

Over 150 MJ/h

input

150 500 1000 1500

T = Flue terminal M = Gas meter Shading indicates prohibited

I = Mechanical air inlet P = Electricity meter or fuse box areas for flue terminals

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances to 50 MJ/h input ................................................................................................ 300

Appliances over 50 MJ/h input ............................................................................................ 500

b - From the ground or above a balcony...................................................................................... 300

c - From a return wall or external corner ..................................................................................... 500

d - From a gas meter (M) ...........................................................................................................1000

e - From an electricity meter or fuse box (P) ............................................................................... 500

f - From a drain or soil pipe......................................................................................................... 150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal......................................................... 500

h - From any other flue terminal, cowl, or combustion air intake ............................................... 500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-floor ventilation:

Appliances up to 150 MJ/h input ......................................................................................... 500

Appliances over 150 MJ/h input ........................................................................................1500

k - From a mechanical air inlet, including a spa blower .........................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of ................................. See table

sub-floor ventilation............................................................................................................. below

8Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

TABLE1

1.2 FLUE SYSTEM APPROVALS

Thesemodels haveflue startingcollars on boththe top

and the back of the unit. Depending upon the installa-

tion, decide which ONE set of starting collars will be

usedto attach theflue system. Thestartingcollarsealing

cap must remain on the starting collar NOT used.

Thesemodels useSL-D-series directflue components

whenusing theTOP flue collarsand DVP-series direct

fluecomponents when usingthe REAR flue collars.

WARNING: YOU MUST NOT MIX DVP-SERIES

AND SL D-SERIES COMPONENTS IN ANY FLUE

SYSTEM CONFIGURATION.

Approved flue system components are labeled for

identification. NO OTHER FLUEING SYSTEMS OR

COMPONENTS MAY BE USED. Detailed installation

instructions are included with each flue termination kit

andshouldbeusedinconjunctionwiththismanual.Figure

5belowshowsfluesystemcomponentsandterminations.

Identifying Flue Components

The flue systems installed on this gas fireplace may

include one, two, or three 90°elbow assemblies. The

relationships of vertical rise to horizontal run in flue

configurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown in

theflueing drawingsand tables onthe next fewpages.

Ifa 90°elbow is first attached tothe unit,the maximum

horizontal run is 2 feet (610mm).

WARNING:THISGASAPPLIANCEANDFLUEAS-

SEMBLY MUST FLUE DIRECTLYTO THE OUTSIDE

AND MUST NEVER BEATTACHED TOACHIMNEY

SERVINGA SEPARATE SOLID FUEL BURNINGAP-

PLIANCE. EACH GAS APPLIANCE MUST USE A

SEPARATE FLUE SYSTEM-COMMON FLUE SYS-

TEMSAREPROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD

COMBUSTIBLE MATERIAL BE CLOSER THAN 3

INCHES (2 1/2 INCHES (64MM) AT WALL FIRE-

STOPS) FROM THE TOP OF THE PIPE OR 1-INCH

TOTHESIDESANDTHEBOTTOMFORHORIZONTAL

SECTIONS OF THIS FLUE SYSTEM. VERTICAL

SECTIONS OF THIS SYSTEM REQUIRE A MINI-

MUM OF 1-INCH (25MM) CLEARANCE TO COM-

BUSTIBLE MATERIALS ALLAROUND THE PIPE.

For alternative installations, other than depicted, con-

tactyour dealer forfurther information.

Refer to Figure 5 for required clearances to flue terminals.

Flue system termination kits

Flue system components

Figure 6. Flue Components and Terminations

MODEL

SL-350TRSI-AUE DVP-TRAP2 & SLK-01TRD HORIZONTALTERMINATION CAP

DVP-TVHW & SLK-991DA VERTICALTERMINATIONCAP

FLUE TERMINATIONAPPROVALS

ERTICAL

TERMINATION

HORZONTAL

TERMINATION

WALL

FIRESTOP

STORM

COLLAR

ROOF FLASHING

HORIZONTAL PIPE

SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING

FIRESTOP

90 DEGREE

ELBOW

SLK-01TRD SLK-991DA DVP-TVHW DVP-TRAP2

DVP-SERIESSL D-SERIES

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

NOTE: PIPES OVERLAP 32mmAT EACH JOINT.

DVP90ST

319mm

286mm

184mm

32mm TYP

13mm TYP

217mm

DVP36

DVP48

1219mm

610mm

914mm

102mm

152mm

DVP4

DVP6

305mm

DVP12

51mm

MIN.

DVP12A

310mm

MAX.

DVP24

251mm

45.0

260mm

DVP45

362mm

Figure 7. DVP-Series Balanced Flue Component Specifications

(127mm inner pipe / 203mm outer pipe)

10 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

Figure 8. SL D-Series Balanced Flue Component Specifications (102mm inner pipe / 168mm outer pipe)

NOTE: PIPES OVERLAP 35mmAT EACH JOINT.

168mm

244mm

162mm

165mm

244mm

SL-90D

165mm

168mm

146mm

298mm

SL-06D

SL-12D SL-17/24D

432-610mm

SL-09D SL-12/17D SL-24D SL-36D SL-48D

222mm

305-432mm

603mm

908mm

1213mm

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo 8000TR-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo LUX36 Bedienungsanleitung

Heat & Glo

Heat & Glo Escape-42DV Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo VRTIKL Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-I35-F Bedienungsanleitung

Heat & Glo

Heat & Glo Soho-N-AU Montageanleitung

Heat & Glo

Heat & Glo PRIMO60 Bedienungsanleitung

Heat & Glo

Heat & Glo BE-41C Bedienungsanleitung

Heat & Glo

Heat & Glo SUPREME-N-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36H-C Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5LP-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo RUTHERFORD-50 Bedienungsanleitung

Heat & Glo

Heat & Glo ATS-AU-D Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo Infinity Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CBV-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-42D Bedienungsanleitung

Heat & Glo

Heat & Glo SLR32 Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO48 Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-I35-F Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-42D Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GL-IPI-R Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRS-CE Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch