Heat & Glo SL-5 Bedienungsanleitung

Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18

TOOLS

Screw gun equipped with 1/4 in (6 mm). socket or

1/4 in. (6 mm). wrench or socket

KIT COMPONENTS

(1) Left Glass Panel

(1) Right Glass Panel

(1) Rear Glass Panel

(2) Lower Glass Brackets (1 left, 1 right)

(1) Rear Lower Glass Bracket

(2) Upper Glass Brackets (1 left, 1 right)

(2) 3/8 in. (9.5 mm) Sleeves

(4) 1/2 in. (13 mm) self-tapping Screws

(2) 1-1/4 in. (32 mm) screws

(1) Top Refractory Panel (SL-X series only)

Leave this manual with party responsible for use

and operation.

Installation Instructions

1. Remove existing brick kit liner and logs from appliance,

if installed. The SL-X series ships standard with a four

piece refractory kit.

2. All Models:

Remove the screw that secures the pilot assembly to

the pilot bracket and gently pull the pilot upward about 2

inches (51 mm).

3. SL-X Series with Standard Refractory Installed:

Locate and remove the two screws that secure the rear

refractory bracket in place. See Figure 2. Retain these

screws for later use.

SL-5, SL-7, SL-9, 350X-AU, 550X-AU: Remove the two

screws adjacent to the air passage as shown in Figure 2.

CAUTION! Risk of Cuts or Abrasions. Wear protective

gloves and safety glasses during installation.

NOTICE: Handle refractory panels with care. Refractory

may chip or crack if dropped or impacted.

GLASS-5, GLASS-7, GLASS-9

GLASS-3X, GLASS-5X, GLASS-7X, GLASS-9X

Models: SL-5, SL-7, SL-9, SL-3X, SL-5X, SL-7X, SL-9X, 350X-AU, 550X-AU

Installation Instructions

CAUTION! Do not install damaged components.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

Figure 1. Metal Components - Components Shown Bent

UPPER GLASS BRACKETS

LOWER GLASS BRACKETS

REAR GLASS

BRACKET

NOTE: Install the lower glass bracket so the bend

clearance notch faces the front of the appliance.

BEND CLEARANCE NOTCH

Figure 2. Remove Screws that Secure Rear Bracket to Firebox

REMOVE SCREWS

2Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18

5. Remove the new rear lower glass bracket from the

packaging and bend the hand bend features “up” to

about 45 degrees. See Figure 4. Install the new rear

lower glass bracket with screws removed in Step 3.

Note: The new lower glass bracket spans the entire

width of the back wall of the rebox and rests above

the side lower glass brackets. See Figure 4, Detail A.

Figure 4. Bend Tabs on Lower Side and Rear Glass Brackets

6. Gently pull the pilot tube and pilot wires down,

grasping them from beneath the rebox to remove

slack in pilot wires. Reattach pilot assembly to pilot

bracket.

7. Locate, remove and discard the two screws

located below the rear exhaust hole. See Figure

5. Install the sleeve onto each 1-1/4 inch (32

mm)screw and install in holes. See Figure 6.

350X-AU, 550X-AU: These screws attach the upper

heat shield to the back of the rebox. Replace

these screws with the 1-1/4 inch (32 mm) screws

and sleeves without removing the heat shield.

Figure 5. Remove Screws

Figure 6. Install Sleeves

REMOVE SCREWS

REAR GLASS BRACKET

DETAIL A

BEND TABS UP

4. Remove lower glass brackets from packaging and

bend “up” hand bend features. See Figure 3. Install

left and right lower glass brackets by installing them

between the outer edges of the left and right hearth

pieces with the notch facing the front of the appliance.

These pieces will t tightly between the hearth sides

and the rebox. See Figure 3.

Figure 3. Install Lower Glass Bracket (Left Side Shown)

NOTCH FACES FRONT OF APPLIANCE

Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18

8. Locate the two upper glass brackets that are shipped

at. Bend the “Right” bracket as shown in Figure 7.

Bend the “Left” bracket shown in Figure 8.

9. Install right upper glass bracket by pushing the bracket

“up” to the rebox top and “out” to the front face of the

rebox. The front edge of the bracket should be tight

to the rebox face and the top edge of the bracket

should be tight to the rebox top. Install the bracket

by inserting the two self-tapping screws through the

bracket into the rebox. See Figure 7. Repeat step 9

for left upper glass bracket installation.

350X-AU, 550X-AU: The right and left upper glass

brackets will slide up to the top of the rebox be

tween the rebox side and the edge of the top

heat shield. Figures 7 and 8 are shown without an

upper heat shield.

Figure 7. Bend Upper Glass Brackets

(Upper Right Bracket Shown)

10. Install the rear glass panel by placing the lower edge

into the rear lower glass bracket. Ensure the smooth

side is facing toward the front of the replace. Tip

glass back until the glass touches the screw head

previously installed in step 7. Keep one hand on the

rear glass panel and proceed to step 11.

11. With one hand on the rear glass panel, bend “up”

one hand bend tab on the upper glass bracket to

approximately 90 degrees. See Figure 8. Once

the hand bend tab is properly bent, the glass panel

will not tip forward. Bend “up” the hand bend tab on

the opposing bracket. The rear glass panel is now

installed. This panel will be held in place by the side

panels once they are installed.

12. Install left glass panel by inserting the glass panel

from the front. Slide panel back until it contacts the

rear glass panel. Ensure that the tab shown below is

bent “down” on each upper glass bracket to secure

left/right glass panels. Repeat step 12 for right glass

panel installation.

Figure 8. Upper Glass Brackets Installed (Left Upper Bracket Shown)

Figure 9. Install Left Glass Panel

BEND THESE

FEATURES

SCREW HOLES

HAND BEND TAB

SUPPORT

TAB

4Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18

Please contact your Heat & Glo dealer with any

questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

Heat & Glo, a brand of Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044

www.heatnglo.com

SL-X Series Only

(Not Installed on 350X-AU or 550X-AU)

Install the top refractory by holding the part horizon-

tally as shown in Figure 11. Insert the top panel into

the space between the rebox top and the top edges

of the side refractory panels as shown in Figure 12.

The refractory panel should rest on all sides of the

glass as shown in Figure 12.

Note: The refractory top panel is designed to t tightly.

It may be helpful to insert the top at a slight angle when

installing as shown in Figure 11.

13. Reinstall logs, glass assembly, and decorative front.

Figure 11. Install Top Refractory Panel

Figure 12. Top Refractory Panel

TOP REFRACTORY

PANEL INSTALLED

Andere Handbücher für SL-5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo 8000CF-OAK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo STELLAR 3-SS-20-G Bedienungsanleitung

Heat & Glo

Heat & Glo Infinity Bedienungsanleitung

Heat & Glo

Heat & Glo 6X-AU Bedienungsanleitung

Heat & Glo

Heat & Glo Foundation Series Bedienungsanleitung

Heat & Glo

Heat & Glo ST-HVB-CE Bedienungsanleitung

Heat & Glo

Heat & Glo COSMO42-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO48 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRS-CE Montageanleitung

Heat & Glo

Heat & Glo 350TSI-P-CEM Sicherheitsleitfaden

Heat & Glo

Heat & Glo ST-36TR-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Heat & Glo

Heat & Glo COSMO-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo MEZZO36 Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo Paloma Bedienungsanleitung

Heat & Glo

Heat & Glo Grand-XTS Bedienungsanleitung

Heat & Glo

Heat & Glo CERONA-36 Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo PIER-36TR-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SL-5-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo CERONA-42 Bedienungsanleitung

Heat & Glo

Heat & Glo SUPREME-N-I30AU Bedienungsanleitung

Heat & Glo

Heat & Glo Heat & Glo LifeStyle Dakota 42-B Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch