heatcon! EM 100 Handbuch
Short instruction Extension module
heatcon! EM 100
0450000604-1915
GB
Short instruction Extension module heatcon! EM 100
S. 2 0450000604-1915_KBA_heatcon!EM100_EbV_EN-Druck.docx
EN Syfety instructions
WARNING
Danger due to live parts.
Some components are electrically live. Contact with live parts can result in an electric shock, burns or even death. Before
working on the electrical system, observe the following points:
Switch the system to a zero volts state. Secure to prevent switching back on. Check for zero volts state.
1 EbV-Device bus
2 A10V Outputs
3 Adress switch
4 Inputs EFI and EFI10V
5 EbV- Device bus
6 230V connection
7 ARS Output
8 ARS Output
9 ARS Output
10 ARSP Output
0450000604-1915_KBA_heatcon!EM100_EbV_EN-Druck.docx S. 3
The heatcon! EM is an expansion for the inputs and outputs of a heatcon! EC inside the system, as shown in the technical data.
Technical data
Installation
Hat rail installation in the energy generator
Outlets
EbV –device bus
Connection technology
4-wire technology, screw terminal connection
Maximal zulässige Kabellänge
50 m
Power supply
230 V ±10 %, 50 Hz
Power consumption
max. 9VA
IP class
0(*)
IP rating
IP00
Fusing
User-supplied
Ambient conditions
•Storage temperature
•Operating temperature
-25 ... +60 °C
-10 ... +50 °C
Connections screw terminals
•Mains voltage L, N
•1 x potential-free relay ARSP, max. 230V / 2A
•3 x relay 230V ARS, max. 2A, sum current: max. 10A
•2 x sensor pulse input EFI
•2 x sensor pulse 0…10V input EFI 10V
•2 x output 0..10V-PWM A10VP
•2 x EbV –device bus
Standards
DIN EN 60730
Dimensions
106 x 90 x 61 mm (length x width x height) with hat rail
Weight
240 g
Colour
Grey
(*) Note
The heatcon! EM 100 is supplied with a top hat rail housing. Protection against contact and the IP 20 degree of protection must
be ensured by installation.
S. 4 0450000604-1915_KBA_heatcon!EM100_EbV_EN-Druck.docx
More information you will find:
https://ebv-gmbh.eu/downloads/
EN –Warranty conditions
Improper use, non-observation of these instructions, use of inadequately qualified personnel and independent changes exclude
any liability on the part of the manufacturer for the resulting damage. The manufacturer's warranty becomes void.
Impairment of device function if incorrect spare parts are used!
If unauthorised parts are used correct functioning is not assured. Use spare parts authorised by customer service.
EN–Declaration of Conformity
EbV Elektronikbau- und Vertriebs-GmbH assures that the product is produced according to valid EU regulations. A complete
version of the Declaration of Conformity can be found in the installation manual at https://ebv-gmbh.eu/downloads/
Copyright
Copyright by
EbV
Elektronikbau- und Vertriebs-GmbH
Heisterner Weg 8-12
D-57299 Burbach
Federal Republic of Germany
Andere heatcon! Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
