Heatilator BIR42-B Bedienungsanleitung

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/23 1

WOODBURNING FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overre and generate

poisonous gases (i.e. carbon monoxide).

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable

materials.

• Keep clothing, furniture, draperies and other ammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

BIR36-B

NOTICE: DO NOT discard this manual!

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• DO NOT overre. Overring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specied. Failure to comply may

cause house re.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury, or death.

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recomends HHT

Factory Trained or NFI certified professionals.

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/232

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the replace or to property.

Table of Contents

1 Product Specic & Important Safety Information

A. Fireplace Certication 4

B. Non-Combustible Materials 4

C. Combustible Materials 4

2 Getting Started

A. Typical Fireplace System 5

B. Design and Installation Considerations 6

1. Selecting Fireplace Locations 6

2. Locating Fireplace & Chimney 7

C. Tools and Supplies Needed 8

D. Inspect Fireplace and Components 8

E. Fireplace System Requirements 8

3 Framing and Clearances

A. Appliance Dimensions/Weight 9

B. Clearances 10

Minimum Clearances to Combustibles 10

C. Construct the Chase 11

D. Frame the Fireplace 12

E. Secure and Level the Fireplace 13

F. Protective Metal Hearth Strips 14

G. Outside Air Kit 14

4 Chimney and Termination Requirements

A. Chimney Requirements 16

B. O󰀨sets/Returns 17

C. Termination Requirements 18

5 Chimney Installation

A. Typical Chimney System 19

B. Assemble Chimney Sections 20

C. Install Chimney Air Kit 20

D. Secure O󰀨set/Return 21

E. Install Ceiling Firestops 21

F. Install Attic Insulation Shield 22

G. Roof Penetration 23

H. Install Chase/Chase Top 23

I. Termination Cap Requirements 24

J. Install Termination Cap 24

6 Shrouds

A. Radiation Shield 26

B. Field Constructed Shrouds 26

1. Open Top Shroud 26

2. Mailbox Style Shroud 27

3. Roofed Style Shroud 27

7 Finishing

A. Finishing Material 28

B. Hearth Extension, Building and Finishing 30

1. Fireplace Installed Flush on the Floor and

Hearth Extension Raised to Bottom of Firebox

Opening 31

2. Raised Hearth Extension and Raised Fireplace 32

3. Fireplace Opening and Hearth Extension Flush

with the Floor 32

C. Non-Combustible Sealant Material 33

D. Mantel and Wall Projections 33

E. Sidewalls/Surrounds 34

8 Fireplace Setup

A. Install Hearth Molded Brick Panel 35

B. Install Back Molded Brick Panel 35

C. Install Side Molded Brick Panel 35

D. Install Screens 36

E. Install Mortar (Optional) 36

F. Grate 36

G. Gas Log/Lighter Provision 37

H. Wood Burning Inserts 37

9 Reference Materials

A. Chimney Components 38

B. Optional Components 42

►

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/23 3

Customer:

Lot/Address

Model (circle one): BIR36-B

Fireplace Install YES IF NO, WHY?

Protective hearth strips installed per manual requirements. (Pg. 14)

Outside air kit installed. (Pg 15)

Chimne

Section 4 & 5 (Pg. 16)

Attic insulation shield installed.

Shrouds Section 6 (Pg. 26)

Shroud is installed properly per instructions.

Finishing Section 7 (Pg. 28)

WARNING! Risk of Fire or Explosion! Failure to install fireplace acording to these instructions can lead to a fire or

explosion.

Verified that the chase is insulated and sealed. (Pg. 11)

Verified clearances to combustibles. (Pg. 10)

Fireplace is leveled and secured. (Pg. 13)

Hearth extension size/height decided. (Pg. 30)

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney air kit installed.

Firestops installed.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjuction with, not instead of, the instructions contained in this installation

manual.

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Roof flashing installed.

Terminations installed.

Combustible materials not installed in non

combustible areas

Hearth extension installed per manual requirements.

Fireplace Setup Section 8 (Pg. 35)

Hearth & Home Technologies recommends the following:

Comments communicated to party responsible

4059-711 • Rev C • 3-25-13

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

All packaging and protective materials removed.

Optional doors properly installed.

Molded brick panels installed correctly.

Grate is properly installed.

Firescreen installed properly.

__________________________ by ______________________on _________

(Builder/Gen. Contractor) (Installer) (Date)

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Manual bag and all of its contents are removed from the fireplace and given to the party

responsible for use and operation.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

• Photographing the installation and copying this checklist for your file.

Combustible materials not installed in non

combustible areas

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/234

WARNING! Risk of Fire! Hearth & Home Technologies

disclaims any responsibility for, and the warranty and

agency listing will be voided by the following actions.

DO NOT:

• installoroperatedamagedreplace

• modifyreplace

• install other than as instructed by Hearth & Home

Technologies

• operate the fireplace without fully assembling all

components

• overre

• install any component not approved by Hearth & Home

Technologies

• install parts or components not Listed or approved

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualied

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel - Iron

- Brick - Tile

- Concrete - Slate

- Glass - Plasters

• Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood - Compressed paper

- Plant bers - Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; ame proofed or

not, plastered or un-plastered

11 Product Specic & Important Safety Information

A. Fireplace Certication

WARNING: This product and the fuels

used to operate this product (wood and

wood pellets), and the products of com-

bustion of such fuels, can expose you to

chemicals including carbon black, which is

known to the State of California to cause

cancer and carbon monoxide, which is

known to the State of California to cause

birth defects or other reproductive harm.

For more information go to: www.P65Warn-

ings.ca.gov.

This replace system has been tested and listed in accor-

dance with UL127 Standards by Underwriters Laborato-

ries Inc. for installation and operation in the United States.

This replace may be installed in sleeping rooms. This

replace is not approved for manufactured housing. If in-

stalled with a gas log set, provisions for the National Fuel

Gas Code must be met.

This replace has been tested and listed for use with the

optional components specied in this manual. These op-

tional components may be purchased separately and in-

stalled at a later date. Installation of an outside air kit will

require signicant reconstruction and is best if installed at

the time of replace installation.

Heatilator is a registered trademark of Hearth & Home

Technologies.

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/23 5

22 Getting Started

A. Typical Fireplace System

Figure 2.1 Typical Fireplace System

Non-combustible

roof flashing maintains

minimum clearance

around chimney

Additional lateral

support for chimney

above roof (or enclosed

in chase) if needed

Ceiling firestop

on floor of attic

Support straps

on rafter supports

chimney (not shown)

Termination cap

Chimney penetrates roof

preferably without affecting

roof rafters

Offset/Return (with hanger straps)

Framing headed off

in ceiling joists

Enclosed space above

and around fireplace

Mantel and surround

Decorative facing

and trim

Hearth extension

Factory-built fireplace

Protective metal

hearth strip(s)

Combustible

framing/header

on top of

V-shaped

standoffs

(spacers)

Chimney system

Attic insulation shield must

be used here to keep insulation away

from chimney if attic is insulated

Storm Collar

Outside Air

(both sides)

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/236

Figure 2.2 Fireplace Locations

NOTICE:

• Illustrationsandphotosreecttypicalinstallationsand

are FOR DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation/appearance may vary due to individual

design preference.

• Hearth & Home Technologies reserves the right to alter

its products.

NOTICE: In addition to these framing dimensions, also

reference the following section:

• Clearances (Section 3).

NOTICE:

A minimum 1-1/2 in. air clearance at the back and

a minimum 1-1/2 in. air clearance to the sides of

thereplaceassemblymustbemaintained.

Chimney sections at any level require a 2 in. mini-

mum air space clearance between the framing

and chimney sections.

B. Design and Installation Considerations

NOTICE: Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, re

o󰀩cials or authorities having jurisdiction over restrictions,

installation inspection and permits.

• Before installing, determine the following:

- Where the replace is to be installed.

- The vent system conguration to be used.

- Gas supply piping.

- Electrical wiring.

- Framing and nishing details.

- Whether optional accessories - devices such as a

fan, wall switch or remote control - are desired.

1. Selecting Fireplace Locations

This replace may be used as a room divider, installed

along a wall, across a corner or used in an exterior chase.

See Figure 2.2.

Locating the replace in a basement should be avoided.

Locating near frequently opened doors, central heat

outlets or returns, or other locations of considerable air

movement can a󰀨ect the performance.

1/2 in. (13 mm) all

configurations

1-1/2 in. min. air space

from fireplace to

combustible materials.

1/2 in. min. air space at

nailing flanges.

Note:

In an exterior chase

or projecting into a

garage

Across a

corner

As a

room

divider Along a wall

78 in.

(1981 mm)

48 in.

(1219 mm)

MINIMUM

24 in. (610 mm)

from fireplace opening to

any perpendicular wall

)

)))))))))))))))

)

)))))))))))))))

)

))

)

))

)

Model # A B C D E F G

in. 72 47 7/8 89 1/8 44 5/8 20 3/8 63 1/8 28 1/2

mm 1829 1216 2264 1133 518 1603 724

BIR36

* 12 in. (305 mm) extra space

included for each outside air

connection. If outside air duct

has no bend, this dimension

may be reduced as long as

minimum clearances are met.

Consideration should be given to these factors before

deciding on a location.

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/23 7

2. Locating Fireplace & Chimney

Location of the replace and chimney will a󰀨ect perfor-

mance.

• Install within the warm airspace enclosed by the building

envelope. This helps to produce more draft, especially

during lighting and die-down of the re.

• Installing the replace in a basement is not recommended.

• Penetrate the highest part of the roof. This minimizes

the e󰀨ects of wind loading.

• Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

• Minimize the use of chimney o󰀨sets.

• Consider the replace location relative to oor and ceiling

and attic joists.

• Take into consideration the termination requirements in

Section 5.

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Not recommended in basement due

to high negative pressure concerns

that effect draft

Figure 2.3 Recommended Chimney Locations

• Install the outside air kit with the intake facing prevailing

winds during the heating season.

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the replace.

• Avoid installing the replace near doors, walkways or

small isolated spaces.

• Recessed lighting should be a “sealed can” design.

• Attic hatches weather stripped or sealed.

• Attic mounted duct work and air handler joints and seams

taped or sealed.

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/238

C. Tools and Supplies Needed

Before beginning the installation be sure the following

tools and building supplies are available:

Reciprocating saw Framing material

Pliers Non-combustible sealant

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

D. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged

parts could impair safe operation. DO NOT install dam-

aged,incompleteorsubstitutecomponents.Keepre-

place dry.

• Remove replace and components from packaging and

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benet.

E. Fireplace System Requirements

The Heatilator replace system requirements consist of

the following:

• Fireplace

- Molded brick panels (hearth panel Included with

replace, side and back panels sold separately)

- Firescreen (included with replace)

- Hearth Extension (sold separately)

- Grate (included with replace)

• Outside Air System

- Air Inlet Hood x2 (included with replace)

- Flex (required, sold separately

• Chimney System

- Attic insulation shield (included with replace)

- Chimney termination cap (sold separately)

• Non-combustible nish material

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/23 9

74 1/8 in.

(1883 mm)

3 3/4 in.

(95 mm)

70 3/4 in.

(1797 mm)

67 3/8 in.

(1711 mm)

61 7/8 in.

(1572 mm)

54 in.

(1372 mm)

38 in.

(965 mm)

5 1/2 in.

(140 mm)

5 in.

(129 mm)

16 1/8 in.

(408 mm)

6 7/8 in.

(175 mm)

11 1/8 in.

(282 mm)

Gas Line

Knockout

11 in.

(281 mm) diameter

11 in.

(281 mm)

27 1/2 in.

(699 mm)

15 1/2 in.

(394 mm)

31 1/8 in.

(790 mm)

74 ° TYP.

5 in.

(129 mm)

16 1/8 in.

(408 mm)

11 1/8 in.

(282 mm)

6 7/8 in.

(175 mm)

46 7/8 in.

(1191 mm)

36 in.

(914 mm)

Gas Line

Knockout

Outside Air

33 Framing and Clearances

A. Appliance Dimensions/Weight

Figure 3.1 Fireplace Dimensions

Model Pounds

BIR36-B 251

Appliance Weight Table

Heatilator • Birmingham 36-B Installation Manual • 4059-709 • Rev AB • 06/2310

(insulation)

Attic

Insulation

Shield

(ceiling)

(roof)

(attic)

(ceiling)

Ceiling Firestop

Offset/Return (secured

with hanger straps)

Storm Collar

Roof Flashing

1-1/2 in. (38 mm) to back &

sides of appliance

(except at nailing flanges

where it is 1/2 in. [13 mm])

Must have 2 in. (51 mm)

minimum clearance

to header

0 in.

to floor

2 in. (51 mm) min.

Shaded areas

represent

2 in. (51 mm) min.

air space clearance

required around pipe

Combustible Object

48 in.

1219 mm

B. Clearances

WARNING! Risk of Fire!

You must comply with all minimum air space clearances

tocombustiblesasspeciedinFigure3.2.DO NOT pack

required air spaces with insulation or other materials.

Framing or nishing material used on the front of, or in

frontof,thereplacecloserthantheminimumslistedmust

be constructed entirely of non-combustible materials (i.e.,

steel studs, concrete board, etc.). Failure to comply may

causere.

Figure 3.2 Clearances to Combustible Materials

Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA

Fireplace to backwall 1-1/2 in. (38 mm)

Fireplace to sidewall 1-1/2 in. (38 mm)

Top stando󰀨s to header 0 in. (0 mm)

Door opening to sidewall 24 in. (610 mm)

MANTEL

Mantel minimum height 22 in. (559 mm)

above opening

Maximum mantel depth 12 in. (305 mm)

Andere Handbücher für BIR42-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heatilator Kamin im Innenbereich Handbücher

Heatilator

Heatilator NB3630M Bedienungsanleitung

Heatilator

Heatilator MEL36 Bedienungsanleitung

Heatilator

Heatilator Wood Burning Fireplace A36C Bedienungsanleitung

Heatilator

Heatilator NBV3630I Bedienungsanleitung

Heatilator

Heatilator SILH20E-B Bedienungsanleitung

Heatilator

Heatilator CRAVE4836 Bedienungsanleitung

Heatilator

Heatilator CD4236-MOD Bedienungsanleitung

Heatilator

Heatilator Gas Fireplace GBFL4136I Bedienungsanleitung

Heatilator

Heatilator HR36 Bedienungsanleitung

Heatilator

Heatilator A36R Bedienungsanleitung

Heatilator

Heatilator NNXT4236IF Bedienungsanleitung

Heatilator

Heatilator NNXT33-IFT Bedienungsanleitung

Heatilator

Heatilator Wood Burning Fireplace ST36D Bedienungsanleitung

Heatilator

Heatilator CD4236IR-C Bedienungsanleitung

Heatilator

Heatilator NASIM Bedienungsanleitung

Heatilator

Heatilator CALIBER DESIGNER B-VENT SERIES Bedienungsanleitung

Heatilator

Heatilator CL36D Bedienungsanleitung

Heatilator

Heatilator SILH50ENH Bedienungsanleitung

Heatilator

Heatilator Heatilator CI60 Bedienungsanleitung

Heatilator

Heatilator Birmingham BIR42 Bedienungsanleitung

Heatilator

Heatilator NEVO3630I-B Bedienungsanleitung

Heatilator

Heatilator ECLIPSE-32 Bedienungsanleitung

Heatilator

Heatilator Wood Burning Fireplace EL36 Series Bedienungsanleitung

Heatilator

Heatilator I80 Gebrauchsanweisung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch