4 31818 Rev J 01/04
ODYSSEY SERIES FIREPLACE WITH GAS LOG SET
A. LISTINGS AND CODE APPROVALS
The Odyssey Series fireplace with factory installed gas log
set has been tested and listed in the U.S. in accordance with
UL127 ( actory Built ireplace), ANSI Z21.50-1998, and ANSI
Z21.60-1996 (Gas Log Set); in Canada, the current ULC S610,
CAN/CGA 2.22-M98 and CGA 2.26-M96, and has been listed
by Underwriters Laboratories Inc. for installation and operation
in the United States and Canada as described in these
installation and operating instructions. All components are
UL, AGA, CGA or CSA safety certified.
The Odyssey Series fireplace with factory installed gas log
set has been tested and listed for use with the optional
components given on page 5. These optional components
may be purchased separately and installed at a later date.
However, installation of an outside air kit and junction box will
require significant reconstruction, and should be installed at
the time of the initial fireplace installation.
Check with your local building code agency prior to installing
this fireplace to ensure compliance with local codes, including
the need for permits and follow-up inspections. In the absence
of local codes, comply with the National Fuel Gas Code, ANSI
Z223.1-Latest Edition in the U.S.; in Canada, the CAN/CGA
B149 Installation Codes. If any assistance is required during
installation, please contact your local dealer or the Heatilator
Technical Services Department, Hearth & Home Technologies
Inc.,1915 W. Saunders Street, Mt. Pleasant, Iowa 52641,
1-800-927-6841.
HEATILATOR® is a registered trademark of Hearth & Home
Technologies Inc., a Division of HON Industries.
WARNING!
This Heatilator fireplace and its components are designed to be installed and operated as a system. Any alteration to
or substitution for items in this system, unless allowed by these installation instructions, will void the Underwriters
Laboratories listing and may void the product warranty. It may also create a hazardous installation. Read through
these instructions thoroughly before starting your installation and follow them carefully throughout your project.
B. DESCRIPTION OF THE FIREPLACE SYSTEM
Odyssey Nomenclature:
Tools and building supplies normally required for
installation:
Tools: Building Supplies:
Saw Wall-finishing materials
Pliers raming material
Hammer ireplace surround
Phillips screwdriver Caulking material
Tape measure
Plumb line
Level
Electric drill/bits
raming square
Note: Illustrations throughout these instructions reflect typi-
cal installations and are for design purposes only. Actual
installation may vary slightly due to individual design pref-
erences. However, minimum and maximum clearances
must be maintained at all times.
The illustrations and diagrams used throughout these in-
stallation instructions are not drawn to scale.
The HEATILATOR® fireplace system consists of the following:
1. ireplace with actory Installed Gas Log Set
2. Hearth Extension
3. Chimney System
4. Chimney Termination Cap
Optional components include:
1. Glass Doors
2. Outside Air System
3. Trim Kit
4. Remote Control
5. Junction Box
6. Chimney Air Kit
24YDOrebmuNedoCredrOecalperiF
24YDO,toliPgnidnatSecalperiF"24seireSyessydO
saGlarutaN
L24YDO ,toliPgnidnatSecalperiF"24seireSyessydO
saGenaporP
We strongly recommend that you DO NOT install B-Vent
Gas Appliances in strong negative air locations, such
as a basement or a public facility. Living rooms with
cathedral ceilings could be susceptible to a negative
air situation, but such installations can be overcome
through raising the termination, depending on specific
installations. This appliance uses room air for normal
operation and could have problems establishing a posi-
tive draft in a negative air location. In lieu, we recom-
mend a Direct Vent Gas Appliance.
