5. ADD/REMOVE
Please read this before installation
The primary controller/gateway has a mode for adding or
removing devices. Please refer to your primary controller
manual on how to set the primary controller in add/remove
mode. The device may only be added or removed from the
network if the primary controller is in add/remove mode.
When the device is removed from the network, it will NOT
revert to factory settings.
An always listening node must be powered continuously
and reside in a fixed position in the installation to secure the
routing table. Adding the device within a 2 meters range from
the gateway can minimize faults during the Interview process.
There are two ways to add the device to a Z-Wave network.
5.1 Method 1: Standard (Manual)
Add/remove mode is indicated on the device by a blinking
green LED. It indicates this for 90 seconds until a timeout
occurs, or until the module has been added to/removed from
the network. Configuration mode can also be cancelled by
performing the same procedure used for starting Configuration
mode. USB cable must be used during add/remove.
To start the configuration process, press the reset button 3
times in rapid sequence. The LED will light up in solid green
for 3 seconds if add/remove is successful. The device is now
ready for use with default settings.
NB! When the device is removed from the gateway, the
parameters are not reset. To reset the parameters, see Chapter
”Factory reset”.
If inclusion fails, please perform a ”remove device” process and
try again. If inclusion fails again, please see “Factory reset”.
5.2 Method 2: SmartStart (Automatic)
SmartStart enabled products may be added to a Z-Wave
network by scanning the Z-Wave QR-Code on the product
if your primary controller supports SmartStart inclusion. No
further action is required and the SmartStart product will be
added automatically after being powered on within range of
the primary controller.
6. FACTORY RESET
Press and hold the reset button. After 3 seconds the LED will
start to blink green. After 20 seconds the LED will start blinking
green rapidly. You may now release the button. If reset was
successful the LED will light up in solid green for 3 seconds.
USB cable must be used during factory reset.
Please use this procedure only when the network primary
controller is missing or otherwise inoperable.
7. STARTUP
After powering up the device for the first time, all the
parameters will have default settings.
8. LED BLINKING PATTERNS DESCRIPTION
The device supports numerous LED blinking patterns to make
it as easy as possible to identify what the device is doing.
Device Not in Network
The LED will blink red when the device is
not added to a Z-Wave network.
Add/Remove
When device enters add/remove mode
the LED will blink green.
If successful, the LED will light up in solid
green for 3 seconds.
If unsuccessful, the LED will light up in
solid red for 3 seconds.
Communication
The device blinks green every time it
sends data over Z-Wave.
Factory Reset
If the button is held for more than 3 seconds, the GREEN LEDwill startblinking with 0.5s intervals..
When the button has been held for 20 seconds, the GREEN LED will blink rapidly with 0.1s intervals for 3 seconds.
Figure 1 (success)
Within the 3 second period the button must be released.
If the button is released within this period, the device will indicate that it has been successfully reset by lighting up in
solid GREEN for 3 seconds. The device will then start blinking RED because it is not included in a gateway.
Figure 2 (fail)
If the button is released before the 3
seconds period, the device will indicate
fail by turning RED LED on for 3 seconds.
Figure 3 (fail)
The button MUST be released between
20 and 23 seconds for local reset to take
place. If held longer, the device will ignore
the command.
9. QR-CODE PLACEMENT (DSK)
The QR-Code is needed when including a device using S2
security or SmartStart. The DSK can be found in the QR-Code
and is located;
• On the product.
• On the Quick Guide.
• On the gift box.
10. SECURITY
S2 security enhances Z-Wave Plus with an additional layer of
AES 128-bit encryption of the wireless Z-Wave communication
to prevent hacking and man-in-middle attacks on the home
network. This device supports S2 and has a Z-Wave DSK QR-
Code label that may be used when the module is added to the
Z-Wave home network. The primary controller will ask for a
5-digit code, which can be found underneath the QR-Code.
0s 1s
0,5s 2s 3s 4s 5s
0s 1s
0,5s 2s 3s xs x+3s
Successful
Unsuccessful
0s 1s 2s 3s
Z-Wave Data transmission indication
4s 5s
0s 1s
0,5s 2s 3s 4s 5s 19s 20s 0,5s 1,5s 2,5s
1s 2s 3s 1s 2s 3s
0s 1s
0,5s 2s 3s 4s 5s
3<x<20s
Released @ x seconds
6<x+3<23s
0s 1s
0,5s 2s 3s 4s 5s 19s 20s 21s 22s 23s 24s20,5s 21,5s 22,5s
