HEIDENHAIN AK LIF 9 W Series Bedienungsanleitung

LIF 982W

Montageanleitung

Edited on:

Change-No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 1/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

These mounting instructions are valid for the

scanning head LIF 98W (ID 1184920-xx) and the scale 902W (ID 658739-01)

Warnings

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 2/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Items Supplied

Figure 1: LIF 98W scanning head covered in shielding bag

Figure 2: LIF 98W scanning head (ID 1184920-xx)

Figure 3: LIF 902W scale (ID 658739-01)

Figure 4: LIF 9x2 mounting aid

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 3/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Mounting the Scale

Remove the scale from the packaging as shown in Figure 5.

Figure 5: Removing the scale

Ensure that the red protective clip remains on the scale. Under no circumstances, never touch the

graduation with your fingers (danger of contamination).

In order to align the scale (figures 6 and 7), the top surface and a side surface of the scale holder both

serve as supports.

Figure 6: Support surfaces for the scale

Figure 7: Aligning the scale

Support surfaces for the scale

Alignments for the scale

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 4/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Four screws (DIN EN ISO 4762 M2 x 6) are recommended for securing the scale.

(Maximum tightening torque: 0.32 Nm).

Figure 8: Securing the scale

Mounting the Scanning Head

Take the scanning head out of the shielding bag

Figure 9: Scanning head with shielding bag

Align the scanning head with the support surface.

Figure 10: Support surface for the scanning head

Support surface

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 5/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Put the head at its approximate position while the protective cover still remains on the scale. Secure

the head loosely in order to allow adjustment. Two screws (DIN EN ISO 4762 M2.5 x 20) and two

washers (DIN EN ISO 7092 2.5) are recommended for securing the scanning head.

Figure 11: Pre-positioned scanning head

Remove the protective clip.

Figure 12: Removal of the protective clip

Set the scanning gap and the distance to the rotation center of the LIF 982 with the mounting aid.

Ensure that the mounting aid is positioned correctly (Figures 13 and 14) and the scale is rotated into

mounting position as shown in dimension drawing (2.8° tilted to scanning head base)

Figure13: Correct position LIF 9x2 mounting aid Figure 14: Incorrect position of the mounting aid

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 6/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Press the scanning head to the support alignments and tighten the mounting screws. (Maximum

tightening torque: 0.65 Nm).

Figure 15: Securing the scanning head

It must be easy to remove the LIF 9x2 mounting aid from the scanning gap after the scanning head

has been mounted.

Figure 16: Removal of the mounting aid

Support alignments for

the scanning head

Change No.

Created Responsible Released Version Rev. Sheet Page

C056927-05

Name Schäfer Schäfer Bauer

D1215163 - 00 -

-01 7/

Serie

Date 25.04.2017 25.04.2017 25.04.2017 Document no.

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Adjusting the Output Signals

A PWM8 phase-angle measuring unit from HEIDENHAIN (Id. Nr. 309 956-xx), for example, along with

a connecting cable (Id. Nr. 331 693-xx) and oscilloscope, is suited for adjusting the output signals.

Figure 17: Accessories for adjustment

Remove the protective cap on the plug of the adapter connector, and remove the cover.

Figure 18: Opened adapter connector

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 8/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

Use the adapter cable (331 693-xx) to connect the LIF 982W to the PWM8, and the BNC outputs of

the PWM with the oscilloscope.

Figure 19: Adjustment setup

The PWM8 displays the signals as shown below.

Figure 20: Display of the signals on the PWM8

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 9/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

The signals can also be displayed on the oscilloscope as follows:

Figure 21: Incremental signal display on the oscilloscope

Figure 22: Reference signal display on the oscilloscope

Five potentiometers and one DIP-switch are available on the adapter connector for adjusting the

signals.

Figure 23: APE PCB with potentiometers

A (0°) B (90°)

PHA

MAMB

360° el

A + B

360°el

Change No. Created Responsible Released Version Rev. Sheet Page

C056927-05 Name Schäfer Schäfer Bauer D1215163 - 00 -

-01 10/

Serie Date 25.04.2017 25.04.2017 25.04.2017 Document no. 12

The reproduction, distribution and utilization of this document as well as the communication of its

contents to others without express authorization is prohibited. Offenders will be held liable for the

The following values are to be checked and/or set:

Signal values Initial operation Fine adjustment Typical values*1)

Signal levels MA, MB(0°, 90°)*2) 0.8 …1.2 Vpp Not possible 0.6 …1.2 Vpp

Amplitude ratio MA / MB0.8 … 1.25 0.95 … 1.05 0.95 … 1.05 P5

Phase angle PHA 90° 10° 90° 5° 90° 3° P4

On-off ratio TVAand TVB

TV = 2 arcsin (|P - N| / M) 0° 15 ° 0° 5 ° 0° 3 ° P2 *3)

P3 *3)

Usable component G 0.2 …0.85 Vpp 0.2 …0.85 Vpp 0.2 …0.85 Vpp

Switching threshold E 0.2·G … 0.7·G 0.2·G … 0.7·G 0.2·G … 0.7·G

Zero crossovers K, L 180° 90° el. 180° 45° el. 180° 45° el. P1

(K-L) / 2 < 90° < 60° < 60° S1 *3)

*1) Typically, these values can be achieved by accurate mechanical mounting and fine adjustment by

potentiometers and DIP-switch. The values are valid up to 20% of the -3dB cut-off frequency in

permissible ranges of temperature, supply voltage and, mounting tolerances.

*2) Recommended signal level for lower fault detection limit 0.3 Vpp / upper fault detection limit 1.35 Vpp

*3) S1 is shifting the reference signal position in 90° steps. In consideration of the tolerance of the

Ref. signal, this allows to adjust the value |(K-L) / 2| < 60°. Depending on the setting of S1,

the Ref. signal is shifted and the allocation of TV1and TV2to P2 and P3 is as follows:

S1 setting

Ref. signal shift 0° -90° +90° 180°

TVx/ Px

allocation TV1= P2

TV2= P3 TV1= P3

TV2= P2 TV1= P3

TV2= P2 TV1= P2

TV2= P3

When reassembling the adapter connector, ensure that no cable wires are crimped.

Figure 24: Assembly of the connector

Andere HEIDENHAIN Industrieanlagen Handbücher

HEIDENHAIN

HEIDENHAIN LC 2x1 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 135 B Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ECI 1319 EnDat22 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN MSE 1110 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN AE LS 4x7 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN LIDA 279 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN MSE 1300 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ERP 880 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN M12 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN VM 182 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN MSE 1180 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ERN 420 TTL Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN KGM 101 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ND 1400 QUADRA-CHEK - GUIDE Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ECN 413 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ERN 9080 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN PP 271A Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TS 460 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN LB 3x2 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN EIB 2391S Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ND 1200R Radial Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ERN 1323 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN ND 2100 G GAGE-CHEK Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 426 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung