HeimVision CA01 Bedienungsanleitung
Camera for HeimVision NVR
System
CA01/CA03
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
3
PACKING LIST
IP Camera x1 DC 12V/1A Quick Guide x1
Power Adapter x1
Screws 5DB Antenna x1
PRODUCT OVERVIEW
Notes:
•CA03 has a microphone while CA01 has not.
•The resolution of CA03 is 3M pixels while CA01 is 2M pixels.
Night Vision Sensor Antenna Ethernet Port DC In
IR LEDs
Microphone
(optional)
Stand
Installation Hole
4
ADD A NEW IP CAMERA TO THE NVR SYSTEM
When you need to add a new IP Camera, please follow the steps below.
Step 1:
Plug the power adapter into the new camera and socket;
Step 2:
Plug the LAN cable into the NVR system and the camera;
Step 3:
Right click on the main interface of NVR system to show the Menu bar, then select Video
Manage.
Step 4:
Click Refresh to show the new IP camera, select it, then click the Match Code to add the
new camera automatically. Then you can unplug the LAN cable.
LAN Cable
Camera
NVR
5
Tip:
After adding the new camera, please right click to show the Menu bar, then select Split
Screen to change the number of the channels showing in the same screen.
EXTEND THE WIFI RANGE
The Wifi signal will be weaker when going through the wall, stairs and other obstacles.
However, there are some solutions that may help to extend the Wifi range.
Adjust the Antennas to the Appropriate Angle
According to the signal transmission character of antenna, it’s better to adjust the
antennas of the cameras to be paralleled with the antennas of the NVR system when
they are in the flat plane or adjust the antennas of the cameras to be vertical to the
antennas of the NVR system when they are in the vertical plane, to receive better signal.
Tip:
Place the NVR on the desk and be far away from the devices that are easy to interfere
the connection, such as microwave oven and TV. Make sure the obstacles between the
NVR and the cameras are as few as possible.
Get an extra Antenna Extension Cable with Stand
Take off the antenna of the IP camera, then install the Antenna Extension Cord into the
IP Camera and put it to the place where the Wifi signal is strong.
Antenna Extension Cord
IP Camera
Window
Wall
NVR
6
Get an extra Repeater Device
To extend the Wifi range, you can also install a Repeater device. Please refer to the user
manual of the Repeater device you bought for using it.
Set up Cascading Connection
Notes:
•When the IPCAM2 is installed out of the Wifi Range, but the IPCAM1 with strong Wifi
signal (check it from the live picture) or with smooth streaming is between the NVR
and IPCAM2, then you can set up the IPCAM1 as a virtual repeater following the
steps.
•This virtual Repeater function cannot strengthen the Wifi signal, but just help to
extend the Wifi distance by the IP Camera.
Step 1:
Right click to show the Menu bar, then click Video Manage > Repeater to enter the
Repeater setting.
7
Step 2:
Click after CH1/IPCAM1, then select 2 to set IPCAM1 as a repeater. This means
CH2/IPCAM2 is connected to the NVR through CH1/IPCAM1.
Step 3:
Click Apply to finish the cascading connection. To check if it’s set successfully, please
click Refresh. To delete the Repeater, left click on the selected channel, then click Apply
and OK.
ADD A CAMERA THROUGH LAN CABLE
If the wifi signal is still too weak, you could switch to connect the IP camera with the NVR
system through LAN cable.
Step 1:
Connect the NVR system and the IP camera to the same router through LAN cable.
Step 2:
Right click on the main interface of NVR system to show Menu bar, then select Video
Manage.
Camera LAN Cable
Router
NVR
8
Step 3:
Select the IP camera of which you would like to switch the connection method, then
delete it.
Step 4:
Click Refresh to show the IP camera, select it, the click Auto Add to add the camera
automatically. The added camera will be shown in the Added device list.
9
SPECIFICATIONS
Operation frequency 2412-2472MHz
Max. RF output power <12dBm
10
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
•Using the product for any purpose other than that for which the product is intended
or failing to follow the instructions for maintenance, operation and service of the
product.
•Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g. during transport, cleaning
by inappropriate means, etc.).
•Natural wear and aging of consumables or components during use (such as
batteries, etc.).
•Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage,
electrostatic discharge voltage (including lightning), faulty supply or input voltage and
inappropriate polarity of this voltage, chemical processes such as used power
supplies, etc.
•If anyone has made modifications, modifications, alterations to the design or
adaptation to change or extend the functions of the product compared to the
purchased design or use of non-original components.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere HeimVision Digitalkamera Handbücher
