Helios FML64PL Bedienungsanleitung

FML64PL

Assembly Instructions

• Please read these instructions carefully before using.

• This model will hold most 32-65 Flat Panel TVs.

• Load capacity: 34kg (75 lbs).

FML64PL

• Please read these instructions carefully before using.

• This model will hold most 32-65 Flat Panel TVs.

• Load capacity: 34kg (75Lbs).

FML64PL Information

• Please read these instructions carefully before starting.

• This product will hold most 32-65 Flat Panel TVs.

• Load capacity: 34kg (75 lbs).

Supplied Parts and Hardware: (Some parts not shown at same scale)

option 1 VESA size:75*75mm,100*100mm.

figure 2

option 2 VESA size:(200-400)*600mm.

Instruction:Attach connecting plate (D) to arm (C) using 4 ,slide

TV bracket (B) onto (C).(figure 2).

Step 1：Read and understand all the directions,handle and use according to the directions

strictly.

Safety Directions:

Step 3：As per different VESA size to choose the suitable unit to assemble them.

Assembly Hareware：

Hardware for TV assembly：

2 - square head

screw 4pcs

3 - concrete

bolt 4pcs

1 - washer

4pcs

a- bolt

4pcs

b- bolt

4pcs

c- bolt

4pcs

d- bolt

4pcs

e- bolt

4pcs

g- washer

4pcs

h- washer

4pcs

i-spacer

4pcs

f- bolt

4pcs

j- wrench

1pcs

k- wrench

1pcs

4 - bolt

8pcs

Step 2：Remove the screws 5 to separate it into two parts.

FML64PL Safety

A--Wall plate 1pc

Supplied Parts and Hardware: Some parts not shown at same scale

Safety Warning: Thanks for choosing this Helios wall mount and please read these instructions

carefully before using the model FML64PL to avoid any injury of anybody and(or) any property

loss. If you do not understand these directions, or have any doubts about the safety of the

installation, please call a qualified contractor or contact Helios customer service department.

Please check carefully to make sure that there are no missing or defective parts. Our customer

representatives can quickly assist you with installation questions and missing or defective

parts. Replacement parts for products purchased through authorized dealers will be shipped to you

directly. Never use defective parts, improper installation may cause damage or serious injuiry. Do not

use this product for any purpose that is not explicitly specified by Helios. Helios is not liable for

damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use.

C--Fixed arm

2pcs

B--TV bracket

2pcs

(Also Figure 8)

Rotate 90°

E- Slide Arm Plate

Figure 1

Figure 2

D- Connecting Plate

Safety Warning

Thank you for selecting the Helios FML64PL for your installation.

Before starting your installation please read and understand all of the

directions.

If you are unsure or have any doubts about the installation please contact

an installation professional or Helios customer support.

• Check the packing list and boxed products carefully to verify

that there are no missing and/or damaged parts.

• Never use damaged or incorrect parts to do your installation as

that may cause property damage or personal injury.

• Our customer service can quickly assist you with installation

questions or parts request.

• Do not use the Helios FML 64PL for any purpose other than

that speciﬁed by Helios. Helios is not liable for damage or injury

caused by incorrect assembly, mounting or use.

Helios customer support:

Hours: Monday – Friday, 9 AM to 7 PM

Phone Number: (866) 839-9187

Email: [email protected]om

Installation and Mounting Directions

Step 1: Read manual completely and understand all of the

directions prior to starting the installation.

Use FML64PL only as described in the directions.

Step 2:

Disconnect the Connecting Plate (D) from the articulated arm by

removing the screws at the bottom rear of the Connecting Plate (D) next

lift the Connecting Plate (D) up and away from the articulated arm.

Then remove the Slide Plate (E) from the Wall Plate (A) by loosing the

two bottom screws and lifting the Slide Plate (E) up and away from the

Wall Plate (A).

option 1 VESA size:75*75mm,100*100mm.

figure 2

option 2 VESA size:(200-400)*600mm.

Instruction:Attach connecting plate (D) to arm (C) using 4 ,slide

TV bracket (B) onto (C).(figure 2).

Step 1：Read and understand all the directions,handle and use according to the directions

strictly.

Safety Directions:

Step 3：As per different VESA size to choose the suitable unit to assemble them.

Assembly Hareware：

Hardware for TV assembly：

2 - square head

screw 4pcs

3 - concrete

bolt 4pcs

1 - washer

4pcs

a- bolt

4pcs

b- bolt

4pcs

c- bolt

4pcs

d- bolt

4pcs

e- bolt

4pcs

g- washer

4pcs

h- washer

4pcs

i- spacer

4pcs

f- bolt

4pcs

j- wrench

1pcs

k- wrench

1pcs

4 - bolt

8pcs

Step 2：Remove the screws 5 to separate it into two parts.

Figure 3

Installation and Mounting Directions

Step 3: Mount the Wall Plate (A) to the wall.

Drywall with Stud mounting: The Wall Plate (A) must be mounted directly

to two wood studs with a minimum distance of 16” between the studs. Once

you have located the correct studs and height for the installation, hold the

Wall Plate (A) in position against the wall, verify with a level and mark the bolt

location for each stud (Figure 1). Next drill 1/8” diameter, 1.25” deep hole at the

four marked locations. Attach the Wall Plate (A) onto the wall with the supplied

lags bolts, level and tighten the lags until Wall Plate (A) is secured.

Concrete Block & Brick mounting: The Wall Plate (A) must be mounted directly

to Solid Concrete, Concrete Block or Brick. Do NOT mount to Mortar joints

or hollow wall sections. Once you have located the correct location for the

installation, hold the Wall Plate (A) in position against the wall, verify with a level

and mark the bolt location for each lag. Next drill 3/16” diameter, 1.25” deep

hole at the four marked locations. Using 3/16” x 1.25” Hex Head Concrete screws

attach the Wall Plate (A) onto the wall with the supplied lags bolts, level and

tighten the lags until Wall Plate (A) is secured.

Note: Be sure to choose a high quality wall area and enough strong to hold the

weight of the TV and wall mount itself. The assembly place should be far

away from water and sunshine

Installation and Mounting Directions:

Step 1：Read manual completely and understand all of the directions prior to starting the installation.

Use (model number) only as described in the directions. .

Figure 1(keep the wall plate level)

Figure 2

Figure 3

Figure 4

Step 3:

Attach two brackets (B) to TV back.

Figure 5

Figure 6

Attention

Forbidden

Note: Be sure to choose a high quality wall area and enough strong to hole the weight of the TV and

wall mount itself perennially when assembling. The assembly place should be far away from the

water and sunshine .

Hollow wall or decorative cardboard

Forbidden

16"

Installation and Mounting Directions

Step 4: Attaching Mount to your display

There are two methods for attaching the mount system to your display. Which

method that you select will be determined by your display.

Method #1 is for displays with a VESA pattern of 75mm x 75mm or 100mm x

100mm or 200mm x 200mm

Method #2 is for displays with a VESA pattern of from 400mm x 400mm up to

and including 400mm x 600mm.

Method #1: Place your display face down on a soft surface.

Select the screws from the included hardware that are correct for your display

then locate the Connecting Plate (A) over the VESA screw receptacles on the

back of your display and secure the Connecting Plate (A) to your display.

Please use the correct screw and washer for the holes on the back of your

display, using the incorrect screw will cause damage to the display.

Note that uneven assembly will cause a slanted screen.

Method #2: Place your display face down on a soft surface. Slide the two TV

Bracket Arms (B) over the two Fixed Arms © and then mount the Connecting

Plate (D) to the correct screw receptacle’s and secure.

Note

Sole intallation

prohibited

Step 6:Connecting wall plate unit and TV connecting unit.

Hang preassembled TV unit onto wall plate unit. Tighten the safety screws.

Step 5：Attach TV connecting unit to TV.

figure 8 figure 9

figure 6 figure 7

Note:1.Please use the corresponding screw&washer for the holes of the TV back, assembling with

incorrect screw & washer will damage the holes on the TV back, uneven assembly will cause slanted

TV screen.

Unit 1

Option 1 VESA:75*75mm,100*100mm.

Unit 1 Lay TV face down,choose the suitable hareware and fix (D) to the back of

TV .Pls keep the TV level(figure 6).

The Wall Plate must be mounted to the wood stud which the width should be at

hold the weight of the TV and wall mount itself. Suggest to ensure the holes location for the Wall Plate

Option 2 VESA:200*200mm,600*400mm.

Unit 2 Lay TV face down,fix (D) onto (B),and then slide (C) onto (B),using the

correct screws to fix them on the back of TV(figure 7).

2.Professional Knowledge required to assemble the flat panel TV and the wall mount and need

at least 2 people to finish this mounting procedure.Do not intent to assemble this wall mount

independently to avoid incorrect assembly or any possible injury this may caused.

Note:1.Pls use the corresponding screw&washer for the holes of the TV back,Asseble with incorrect

screw & washer will damage the holes on the TV back,uneven assembly will cause slantwise TV

screen.

Note

Sole intallation

prohibited

Step 6:Connecting wall plate unit and TV connecting unit.

Hang preassembled TV unit onto wall plate unit. Tighten the safety screws.

Step 5：Attach TV connecting unit to TV.

figure 8 figure 9

figure 6 figure 7

Note:1.Please use the corresponding screw&washer for the holes of the TV back, assembling with

incorrect screw & washer will damage the holes on the TV back, uneven assembly will cause slanted

TV screen.

Unit 1

Option 1 VESA:75*75mm,100*100mm.

Unit 1 Lay TV face down,choose the suitable hareware and fix (D) to the back of

TV .Pls keep the TV level(figure 6).

The Wall Plate must be mounted to the wood stud which the width should be at

hold the weight of the TV and wall mount itself. Suggest to ensure the holes location for the Wall Plate

Option 2 VESA:200*200mm,600*400mm.

Unit 2 Lay TV face down,fix (D) onto (B),and then slide (C) onto (B),using the

correct screws to fix them on the back of TV(figure 7).

2.Professional Knowledge required to assemble the flat panel TV and the wall mount and need

at least 2 people to finish this mounting procedure.Do not intent to assemble this wall mount

independently to avoid incorrect assembly or any possible injury this may caused.

Note:1.Pls use the corresponding screw&washer for the holes of the TV back,Asseble with incorrect

screw & washer will damage the holes on the TV back,uneven assembly will cause slantwise TV

screen.

Installation and Mounting Directions

Once assembled place on the back of your display and line up with the VESA

screw receptacles, using the correct screws for your display secure the TV

Bracket Arms (B), then secure the Fixed Arm © to the TV Bracket Arms (B)

with the included hardware.

Please use the correct screw and washer for the holes on the back of your

display, using the incorrect screw will cause damage to the display.

Note that uneven assembly will cause a slanted screen.

Step 5:

Mount the Slide Arm Mount (E) onto the now mounted Wall Plate (A)

and select your left to right position. Once you have the Slide Arm Mount (E) in

the desired location secure into place by tightening the the two screws at the

bottom of the Slide Arm Mount (E) back plate.