Helipal Storm Handbuch

Andere Handbücher für Storm

1

Andere Helipal Drohne Handbücher

Helipal

Helipal storm racing drone 370 Bedienungsanleitung

Helipal

Helipal Storm Bedienungsanleitung

Helipal

Helipal SRD-Y3 Bedienungsanleitung

Helipal

Helipal SRD180 v3 Bedienungsanleitung

Helipal

Helipal SRD260 Pro v2 Bedienungsanleitung

Helipal

Helipal SRD280 Bedienungsanleitung

Helipal

Helipal Storm Drone 8 Bedienungsanleitung

Helipal

Helipal storm SRD101 Bedienungsanleitung

Helipal

Helipal Luminer QAV-X Storm Edition Bedienungsanleitung

Helipal

Helipal Storm Racing Drone Type B Lite Bedienungsanleitung

Helipal

Helipal SRD250 Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

dji

dji Matrice M210 Bedienungsanleitung

MAKE

MAKE Terry Kilby Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

dji

dji PHANTOM 4 Bedienungsanleitung

Atlas

Atlas AtlasPRO Bedienungsanleitung

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

dji

dji WIND-4 Bedienungsanleitung

1

Copyright@2015 HeliPal.com. All Rights Reserved

Storm Racing Drone

(w/NAZA GPS CONTROLER)

Binding Procedure

For RadioLink AT-9 Radio controller

V1.3

2

Copyright@2015 HeliPal.com. All Rights Reserved

How to Bind

You can follow the binding procedure below to connect the drone receiver with Radio Link AT9

Radio controller

Press the switch inside the receiver twice with small screwdrivers to make LED indicator turns PURPLE to set the

control mode to D Bus Mode. (Skip this step if it is default in Purple light)

Use the small screwdrivers to press and hold the switch inside the receiver until it is flashing with light in Blue and

Purple, Switch on the radio controller, it will start searching for available receiver. Receiver will stop flashing while the

bind process complete and the radio controller will the signal strength on the screen

3

Copyright@2015 HeliPal.com. All Rights Reserved

Radio Controller Parameters

Please apply the setting below for :

1) Press and Hold the controller wheel (With wordings

“PUSH”) to unlock the manual. Press and Hold Mode

Button to go into basic menu page

2) [STK-MODE] = 2 (Stick Mode)

[LockScreen] = 30s (Time to lock screen)

3) [TYPE] = AIRCRAFT

4) [SELECT] = 01

[NAME] = SD-NAZA (Any name you want)

5) Go to [AUX-CH] -> ATTITUDE, apply the setting below:

[CH] = CH7 [SW3] = SwG [SW2] = NULL

[GPS] = 0% [ATTI.] = 50% [ATTI.] = 100%

6) [CH5] = VrA [CH6] = SwE [CH7] = -------

[CH8] = VrB [CH9] = SwA [CH10] = SwB

4

Copyright@2015 HeliPal.com. All Rights Reserved

7) [CH7]->[L]= 56% (Move the toggle Switch Gto lowest)

[CH7]->[H]= 56% (Move the toggle Switch Gto highest)

8) [AUX2] = -13

9) [AUX2] = REV

10) [F/S][THRO] = 0%

[F/S][AUX2] = +28%

11) [1] [TIME] = 10:00

[1] [MODE] = UP

[1] [ON][1] = ST-THK (Using Throttle Stick to start the

timer)

[1][ON] [2] = 15% ( Move the indicator over the value,

set throttle stick to around 15%, Press and hold “Push”

button to recognize the throttle value and move the

wheel to change the arrow sign)

[1][RESET] [1] = SwH (Using Switch H to responsible

for the reset timer action)

[1][RESET] [2] = DOWN (Using Switch H’s down action

to reset the timer)

5

Copyright@2015 HeliPal.com. All Rights Reserved

How to Control