Hella ONYX.NODE Einrichtungshandbuch

Installation Instructions and Instructions for Use

These instructions must be read

prior to installation

and use!

Control device ONYX.NODE

Installation instructions

Operating guidelines

Installation Instructions and Instructions for Use

Table of Contents

Preliminary remarks HELLA Control device ONYX.NODE....................................................1

General notes ........................................................................................................................2

Safety instructions..................................................................................................................3

Designated use ......................................................................................................................4

Scope of delivery ...................................................................................................................5

Device description..................................................................................................................5

Technical data........................................................................................................................6

Installation..............................................................................................................................6

Connection diagram...............................................................................................................7

Configuration..........................................................................................................................9

Operating guidelines ............................................................................................................10

Settings ................................................................................................................................11

Ideal use of the radio signal .................................................................................................14

Fault removal .......................................................................................................................15

Disposal ...............................................................................................................................15

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 1

Preliminary remarks HELLA

Control device ONYX.NODE

With this HELLA product you have opted for a high-quality product with a most up-to-date

technology that can nevertheless be easily installed and operated. In these instructions we

describe the basic installation, commissioning and use.

These instructions are addressed to trained electricians.

The following symbols will assist you with the installation or use and require a safety-

conscious conduct:

Attention!

This symbol indicates instructions that, if disregarded, can put the user

in danger.

Attention!

This symbol indicates instructions that, if disregarded, can potentially

result in damage to the product.

This symbol indicates instructions for use or helpful information.

This symbol requires you to act.

Attention!

This symbol indicates a risk of injury or danger to life due to an electric

shock.

This symbol indicates parts of the product, for which you will find im-

portant information in these installation instructions.

Installation Instructions and Instructions for Use

2 Subject to technical modifications – Date of Issue May/2020

General notes

Questions

In case of questions concerning the installation or the use of your product, please consult

your authorized specialist shop.

Warranty

Warranty claims are subject to statutory limitation periods. Wear parts are excluded from

the warranty; the same applies for changes in colour and changes in characteristics

caused by UV radiation.

Liability

In case of non-observance of the directions and information given in these instructions and

in case of improper operation or unintended use, the manufacturer shall not accept any

warranty claims concerning any damage to the product. In these cases the liability for

consequential damage to any parts or persons is ruled out as well.

Legal notes

The graphs and texts of these instructions were carefully prepared. We cannot be held

liable for any errors and their potential consequences! Subject to technical modifications to

the product and to these instructions! These instructions include copyrighted information.

owners.

EC declaration of conformity

The HELLA Sonnen- und Wetterschutztechnik GmbH hereby declares that this product

complies with the basic requirements and the other applicable regulations of the EC direc-

tives. The complete declaration of conformity can be found in the download area of our

website https://www.hella.info.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 3

Safety instructions

These installation instructions refer to prefabricated elements, that (1) for

100% are made from parts, which are defined by us, and (2) which are made

in manufacturing processes, which are defined by us too; in all other cases

we do not provide any guarantee!

The safety instructions as well as the appropriate instructions must be read

carefully before installation and use. In case of non-observance of the direc-

tions and information given in these instructions and in case of improper

installation and operation or unintended use, the manufacturer shall not

accept any warranty claims concerning any damage to the product. In these

cases the liability for consequential damage to any parts or persons is ruled

out as well.

- Follow the described installation steps and pay attention to recommenda-

tions and notes.

- Keep these instructions in a safe place.

- All installation and removal works, as well as maintenance and repair

works are only allowed to be carried out by authorised and qualified spe-

cialist staff.

- Observe the regulations for prevention of accidents of the employer's

liability insurance association!

- Before operation check the unit for visible damage. If the unit is damaged,

it should not be used; please consult authorized specialist staff immedi-

ately.

- Only use unmodified original parts from HELLA.

- In case of unauthorised opening of the device, improper use, incorrect

installation or incorrect operation, there is a risk of damage to persons or

property.

- Never let children play with the unit.

Use ONYX.NODE in dry rooms only.

Installation Instructions and Instructions for Use

4 Subject to technical modifications – Date of Issue May/2020

Safety instructions

Attention! Risk of injury or danger to life due to an electric shock!

- Set-up, examination, commissioning and error correction of the unit must

only be performed by authorised or trained expert staff (as per VDE

0100).

- Switch off the current to the connecting lines when working at the unit.

There is danger to life! Take safety precautions against unintentional

switching on!

- Check the electrical wires regularly for damage. Do not use the unit if any

damage is found.

Observance of regulations and rules

The building owner is responsible for the observance of statutory rules and

country-specific provisions on site.

Designated use

The control device ONYX.NODE may only be used for the control of outdoor blinds / exte-

rior Venetian blinds, roller shutters, awnings and facade blinds that are provided with

drives, which are intended for this use. With ONYX.NODE, the lighting may be used up to

the performance data given. Any use other or beyond that is not considered intended use.

The connection of external devices must be carried out in consultation with the specialist

staff. ONYX.NODE is a single control device, which means that only one drive can con-

nected per ONYX.NODE.

- It is not allowed to use radio system in areas with an increased risk of

interference (e.g. hospitals, airports).

- The remote control is only admissible for devices and systems, where a

malfunction in the transmitter or receiver does not pose a risk to persons,

animals or objects, or if this safety risk is covered by other safety installa-

tions.

- Follow the wiring diagram precisely!

- We cannot accept responsibility for damage, that can result from improper

installation.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 5

Scope of delivery

The following components are included in the scope of delivery:

- Control device ONYX.NODE (quantity as per purchase order)

- Short instructions control device ONYX.NODE

Device description

ONYX.NODE

Art. no. 50680002

220-240 V AC / 50-60 Hz

ONYX.NODE is a control device for the interior (flush-mounted socket). It is suitable for the

control of 230 V Venetian blind, roller shutter and awning motors, as well as for the switch-

ing on/off of 230 V lights.

Fig. 1: Connections:

Legend

No function

Mains connection input N

Pushbutton connection DOWN

Mains connection output N

Pushbutton connection UP

Motor connection DOWN

Pushbutton connection +

Motor connection N

Mains connection input L

Motor connection UP

Mains connection output L

Installation Instructions and Instructions for Use

6 Subject to technical modifications – Date of Issue May/2020

Technical data

Input 220-240 V AC / 50-60 Hz

Output 450 VA

Nominal capacity 0.3 W

IP rating IP20

Admissible ambient temperature 0 °C to +55 °C

Radio frequency 868.3 MHz

Transmission power 12.6 mW

Installation type Flush-mounted box min. ø65 mm (inside),

depth min. 60 mm; surface-mounted in

corresponding surface-mounted casing

Dimensions LxWxH 49x49x24.5 mm

Weight 48 g

Installation

Prior to starting the installation, check the proper function of the transmitter

and the receiver at the desired installation position. The flush-mounted box

must be fastened in a way that the drilled hole does not hit wiring. Extended

instructions for the electrical installation can be found in the download area

of our website http://www.hella.info.

Minimum requirements flush-mounted socket: ø65 mm (inside), 60 mm

deep.

1. Place the ONYX.NODE in the box.

2. Connect the stripped cables without end sleeves, as shown in Fig. 2.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 7

Connection diagram

ONYX.NODE

0+N

N N L L

LOCAL MOTOR

POWER

1,5mm

0,5mm

0,75 - 1,5mm

ONYX.NODE

0+N

N N L L

LOCAL MOTOR

POWER

1,5mm

0,5mm

0,75 - 1,5mm

2 34 5

6 6

Fig. 2: Wiring diagram for Venetian blind, roller shutter and awning motor, lighting

Legend

Junction box

Motor

Button

Lighting

Switch (pushbutton possible)

ONYX.NODE

Installation Instructions and Instructions for Use

8 Subject to technical modifications – Date of Issue May/2020

Connection diagram

Attention!

The motor cable must be directly connected to the control device ON-

YX.NODE: Clamping points/junctions in the motor cable are unacceptable.

Attention!

When actuating the 230 V lighting, the maximum output power of 450 VA

may not be exceeded. This must especially be observed with lightings with

electrical ballasts, which have a high inrush current.

In addition, a cut-off relay must be used with higher electric capacities.

“Power”-terminals for mains voltage 230 V AC / 50 Hz

The input is provided for the voltage supply of the module and the load. The names L and

N mark live cord and neutral conductor. Both clamps (L and N) are present in duplicate, the

voltage supply can thus be transferred to the next control device. Observe the terminal

assignment in Fig.1.

"Motor"-terminals for motor connection

The outputs are provided for the connection of the drive or the connection of the lighting.

The arrows on the device show the running direction of the drive. 230 V lighting is con-

nected to N and (L).

"Local"-terminals for pushbutton

To control the ONYX.NODE, a Venetian blind pushbutton or a switch / pushbutton for the

lighting can be connected to the terminals “Local”. Hence, the ONYX.NODE can also be

operated without a smart phone. Up to four ONYX.NODE (Art.-No. 50680002) can be

connected to a central pushbutton (a switch in case of lighting possible). If several ON-

YX.NODE are to be operated by one pushbutton, the following must be observed:

- All ONYX.NODE must be connected to the same phase.

- If several ONYX.NODE are operated by one pushbutton only, make sure that L and N

are not interchanged.

- The cabling may only be performed in a de-energized condition.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 9

Connection diagram

Direction assignment of the outputs when connecting a Venetian blind, roller shut-

ter, awning motor

After having connected the drive, please check the direction assignment of the outputs.

When pressing the pushbutton into the UP-direction, the motor must move into the retract-

ing direction. When pressing the pushbutton into the DOWN-direction, the motor must

move into the extending direction. If this is not the case, please exchange the connections

on the outputs. The direction assignment can take place through the ONYX®-app at a later

time.

Configuration

Before configuring the ONYX.NODE, download HELLA’s free app ONYX®

from the app store / Google Play to your smart phone.

Before you can use ONYX.NODE in combination with ONYX.CENTER or

ONYX.CLICK, ONYX.NODE must be added in the app ONYX®. You will find

all information regarding the configuration in the instructions for ON-

YX.CENTER / ONYX.CLICK, directly in the app ONYX®or in the download

area on our homepage https://www.hella.info.

Precondition:

ONYX.NODE is installed (see chapter “Wiring diagram”). The mechanical

end positions of the drives must be adjusted.

Installation Instructions and Instructions for Use

10 Subject to technical modifications – Date of Issue May/2020

Operating guidelines

Roller shutter mode

If a pushbutton is pressed briefly, the drive moves to the respective end

position (latching mode). As a standard, the roller shutter mode is adjusted

on delivery.

Venetian blind mode

If the pushbutton is pressed briefly (<2 seconds), the drive stops after releas-

ing the pushbutton (tilting mode). If the pushbutton is pushed for more than

two seconds, the drive moves to the respective end position (latching mode).

Light mode

When pressing the pushbutton, the lighting is switched on. When pressing

the pushbutton again, the lighting is switched off. Only in the light mode, also

a switch can be connected to the control device.

Groups

Groups with their different sun protection units can be configured freely in the

ONYX®-app. All units in one group can be controlled together.

Favourite position (heart symbol)

In the ONYX®-app six freely selectable positions per sun protection unit can

be saved, which you simply can use again at a later time.

Automatic Operation

In the ONYX®-app you can set up as many time functions as you like, which,

at the desired times, make your sun protection units move to the adjusted

positions. ONYX®is also provided with an astro function, which, at sunrise or

sunset, moves your sun protection unit automatically to a defined position.

With the help of the sun sensor a particular position can be defined, if the

threshold value of the sun is below or exceeds the preset value.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 11

Settings

Device type

The different device types can be selected in the ONYX®-app under “ad-

vanced settings”.

It is necessary to define the type of device. By selecting the appropriate

category, it is assigned to this type. Device types are outdoor blind, roller

shutter, awning, facade blind and light. For device types, you do not want to

be displayed in the app, i.e. central pushbutton without a connected drive,

the drive type “Hidden” is available. By default the device type “Roller shut-

ter” is set.

Outdoor blind parameters

You find the outdoor blind parameters under “advanced settings” in the ON-

YX®-app.

Under “Tilting time” it is possible to transmit the time the outdoor blind re-

quires for a complete tilting to the ONYX®control. This must especially be

observed, if a drive with a slow slat tilting is mounted.

Preset tilting times:

Outdoor blind 90°: 1.25 s

Outdoor blind

180°:

2.5 s

Motor parameters

You find the adjustment possibilities for the motors under “advanced set-

tings” in our ONYX®-app.

If your sun protection unit moves contrary to the direction of your control

command, you can activate the reversal of the direction of rotation with the

icon “Reverse direction of rotation”.

In addition, the “automatic running time” can be activated/deactivated under

“motor parameters”. The automatic running time should be deactivated only,

if ONYX.NODE is not directly connected to a drive, i.e. to a cut-off relay. The

running time can be adjusted manually, when the automatic running time is

deactivated. As a standard the automatic running time is activated.

Installation Instructions and Instructions for Use

12 Subject to technical modifications – Date of Issue May/2020

Settings

Pushbutton settings

You find the adjustment possibilities for the pushbutton under “advanced

settings” in the ONYX®-app.

The actuating direction at the connected Venetian blind pushbutton can be

reversed with “Reverse direction of pushbutton”. This function can be useful,

if the Venetian blind pushbutton is not correctly connected to ONYX.NODE.

Under “Forwarding pushbutton actuation” the pushbutton signal of the con-

nected Venetian blind pushbutton can be forwarded to other ONYX®compo-

nents. This function can be used for groups, which can be activated via one

single pushbutton.

Wind resistance class

You find the wind resistance classes in the ONYX®-app under “advanced

settings”. These preset wind resistance classes are only relevant, if the op-

tional weather sensor ONYX.WEATHER is used. Please note, that the real

values set depend on the installation situation on-site; these values are

available in the documentation of the sun protection device and must be

strictly observed!

Preset wind resistance classes:

Roller shutter Class 4 (13.8 m/s)

Awning Class 2 (10.7 m/s)

Facade blinds Class 4 (13.8 m/s)

Outdoor blind Class 4 (13.8 m/s)

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 13

Settings

Output selection and entry type

These two adjusting possibilities are only available for the device type “light”.

Under “output selection” you can select the output of the “motor”-terminal to

be used for the actuation of the lighting. It is possible to select between

“Channel A” (connection N and ) and “Channel B” (connection N and ).

As a standard “Channel A” is set.

Under “Entry type” you can select, if a pushbutton or a switch is connected to

the control device.

As a standard “pushbutton” is set.

A detailed description of all settings of the ONYX®-app are available in the

download area of our website https://www.hella.info.

Installation Instructions and Instructions for Use

14 Subject to technical modifications – Date of Issue May/2020

Ideal use of the radio signal

In case of bad reception, the position of the ONYX.NODE must be changed.

Radio systems that send on the same frequency may cause interference

with reception.

It must be considered that the range of the radio signal is limited by statutory

regulations and structural measures.

Installation Instructions and Instructions for Use

Subject to technical modifications – Date of Issue May/2020 15

Fault removal

Problem Possible cause Troubleshooting

Drive does

not run or

runs only

briefly.

Motor connec-

tion incorrect.

Check the connection as per Fig. 2. Change connec-

tion, if necessary.

Lighting can

not be con-

trolled.

Incorrect con-

nection.

Drive runs

into the

wrong direc-

tion.

Directions were

interchanged

during installa-

tion.

Perform the reversal of the direction in the ONYX®-app,

as described in the chapter “Settings”.

Incorrect

operation

when control-

ling the light-

ing via a light

switch.

Entry type with

ONYX.NODE is

set to “pushbut-

ton”.

Selection of the entry type “light switch” in the ONYX®-

app, as described in the chapter “Settings”.

ONYX.NODE

can not be

controlled in

the ONYX®-

app (off-

line).

- The wrong

control de-

vice was

added.

- No mains

voltage at

the ON-

YX.NODE.

- Check if the serial number is correct and add it

again.

- Provide mains voltage with ONYX.NODE.

Poor or no

radio recep-

tion.

Adverse posi-

tion of ON-

YX.CENTER /

ONYX.CLICK or

ONYX.NODE.

Reposition ONYX.CENTER / ONYX.CLICK or ON-

YX.NODE.

Device

locked.

ONYX.NODE is

already config-

urated in an-

other network.

Follow the instructions on your screen, perhaps voltage

interruption.

Disposal

Dispose of the device in accordance with the current country-specific regula-

tions for electronic scrap (e.g. collecting points).

Installation Instructions and Instructions for Use

HELLA Interior Venetian

Blinds

regulate the lighting in a room

very comfortably, immediately

gracing it with much more at-

mosphere.

HELLA Insect Screens

and you decide who is allowed

to come in and who isn't.

HELLA Pleated Blind

folds up very compactly and

protects very well against the

sun and nosey glances where

only little space is available.

HELLA Venetian Blinds

serve for the light regulation, as

view protection, anti-glare blind

and heat protection.

HELLA Front-mounted

Roller Shutter

for more safety and protection

against rain, wind, heat, the

cold, noise and nosey glances,

also available for subsequent

installation.

HELLA Facade Awning

with exposing mechanism for

lovely facade design with per-

fect heat protection and anti-

glare blind.

For questions, wishes and ideas:

HELLA Infoline +43/(0)4846/6555-0

HELLA Sonnen- und Wetterschutztechnik GmbH

A-9913 Abfaltersbach, No. 125

Tel.: +43/(0)4846/6555-0

Fax: +43/(0)4846/6555-134

e-mail: [email protected]

Internet: http://www.hella.info

Inhaltsverzeichnis

Andere Hella Steuereinheit Handbücher

Hella

Hella ONYX.CENTER Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung