Helmholz Profinet 700-850-4PS01 Bedienungsanleitung

Quick Start Guide PROFINET Switch 4/8-port

Version

2en

www.helmholz.de

Quick Start Guide PROFINET Switch 4/8-port

Version

Quick Start Guide PROFINET Switch 4/8-port

Contents

1. Introduction 3

2. Preparing the PROFINET switch 4

3. Project planning for PROFINET switch 4

4. Setting the port properties 6

5. Topology detection 7

6. Assign the PROFINET switch a name 8

7. Media Redundancy Protocol (MRP) 9

8. Diagnosis and conguration via the web interface 10

9. Switch diagnosis and settings 12

10. Port mirroring 12

11. Statistics 13

12. Agents 14

13. SNMP 15

14. Setting the time 16

15. Resetting to factory settings 17

16. Firmware update 17

17. LED status information 18

18. Button functions 18

19. Technical data 19

Quick Start Guide PROFINET Switch 4/8-port

1. Introduction

Please note: Please observe the safety instructions for the product, which can be found

in the manual. You can nd the manual on the accompanying CD or it can be down-

loaded from the website www.helmholz.de in the download area.

This document should explain the initial commissioning of the PROFINET switch for

use in a PROFINET project.

FCN: Function button

RST: Reset button

P1 — P4:

For PROFINET devices

or other Ethernet

devices

Voltage supply Operation LEDs (see page 18)

FCN: Function button

RST: Reset button

Voltage supply Operation LEDs (see page 18)

P1 — P8:

For PROFINET devices

or other Ethernet

devices

Quick Start Guide PROFINET Switch 4/8-port

3. Project planning for PROFINET switch

Following installation, the PROFINET switch can be found in the hardware catalog

under "PROFINET IO -> Additional Field Devices -> Network Components ->

Helmholz PN-Switch". Add the "PROFINET Switch, 4-port" device to the project and

connect it with your PROFINET network.

2. Preparing the PROFINET switch

2.1 Connection

The PROFINET switch must be supplied with 24 V DC at the wide range input

18 – 30 V DC via the provided connector plug. The terminal (FG) is for the functional

ground. Connect this correctly with the reference potential.

The RJ45 sockets “P1 – P4”(4-port switch) and “P1 – P8” (8-port switch) are for the

connection of the network.

2.2 Install GSDML le

The GSDML le can be found on the accompanying CD or in the download area of

the PROFINET switch at www.helmholz.de.

Quick Start Guide PROFINET Switch 4/8-port

By calling up the object properties, you can assign the PROFINET switch a unique

PROFINET name and check the IP address for plausibility in the project.

Important: The real device must later be assigned the same name as in the project. See

also Chapter .6

Quick Start Guide PROFINET Switch 4/8-port

4. Setting the port properties

Each port of the PROFINET switch can be individually congured.

Transfer medium/duplex:

“disable” The port is permanently switched off. This option is recommended when the port is not to be used. Unauthorized

inltration of the network is prevented.

“Automatic settings” The port synchronizes itself automatically with the communication partner (auto-negotiation).

“Automatic settings (monitor)” The port synchronizes itself automatically with the communication partner (auto-negotiation). A diagnosis alarm is

triggered in the event of an absent Ethernet cable.

“TP 100 Mbps“ Fixed specication of the transmission rate. This option is recommended when connecting PROFINET IO devices.

Quick Start Guide PROFINET Switch 4/8-port

5. Topology detection

The PROFINET switch supports the mechanisms for neighborhood detection (LLDP).

With this function it is possible to detect the topology of a PROFINET network, or to

specify it for purposes of checking for the correct structuring by the conguration.

If the topology was prescribed in the conguration, neighboring devices can also be

assigned the PROFINET name in the event of the replacement of a device.

The exchange of a device in operation is thus possible without the use of commis-

sioning tools.

Quick Start Guide PROFINET Switch 4/8-port

6. Assign the PROFINET switch a name

When the conguration of the PROFINET switch has been completed in the hardware

congurator, it can be loaded into the PLC.

In order that the switch on the PROFINET can be found by the PROFINET controller,

the PROFINET name must be set in the device.

To this purpose the function "Process Ethernet participant" is used in the SIMATIC¹

manager.

With the "Browse…" button, the network can be browsed for PROFINET participants.

The clear identication of the PROFINET switch is ensured here by the MAC address

of the device.

Important: The assigned name must agree with the name dened in the hardware

congurator. See Chapter 3, pages 4/ 5

If the PROFINET switch has been assigned the correct name, it is recognized by the

PLC and congured.

If conguration has taken place correctly, the green "RUN" LED should be on and the

"BF" and "SF" LEDs off.

Quick Start Guide PROFINET Switch 4/8-port

7. Media Redundancy Protocol (MRP)

The PROFINET switch supports the optional media redundancy protocol (MRP) as

MRP client. MRP stands for "media redundancy protocol". MRP enables ring wiring,

which also makes operation of the PROFINET network possible in the event of the

failure of a cable or of a participant.

There must be at least one MRP master (e.g. the CPU) in an MRP ring. All other

participants of the ring are then MRP clients.

Helmholz

TB20-C| PROFINET IO

Helmholz

TB20-C| PROFINET IO

CPU

PROFINET-Switch

I/O System

Operator Panel

MRP Ring

Engineering Station

X1 P4X1 P1 X1 P2 X1 P3

Ext. V DC

18... 30 V

+FE IN1 IN2–

PROFINET-Switch

4-Port, managed

FCN

RST

PWR

RUN

MAC:

00-00-00-00-00-00

In order to assign the PROFINET switch to an MRP ring, the MRP domain must be set

at slot X1 for the option "Media Redundancy".

Important: If ring wiring is produced without the MRP roles being congured for all

devices involved, this can result in functional disruptions of the PROFINET network!

Quick Start Guide PROFINET Switch 4/8-port

8. Diagnosis and conguration via the web interface

The web interface is also accessible under the IP address assigned to the PROFINET switch in the PROFINET network.

When the web interface is rst called up, the password of the "admin" user is "admin" (as of rmware V1.02 the password is the serial number of the device).

It is absolutely necessary to assign a new password following the rst login:

Andere Handbücher für Profinet 700-850-4PS01

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Helmholz Schalten Handbücher

Helmholz

Helmholz FLEXtra Bedienungsanleitung

Helmholz

Helmholz 700-856-12F41 Bedienungsanleitung

Helmholz

Helmholz Profinet 700-850-4PS01 Bedienungsanleitung

Helmholz

Helmholz Profinet 700-850-4PS01 Bedienungsanleitung

Helmholz

Helmholz 700-857-8PS01 Bedienungsanleitung

Helmholz

Helmholz FLEXtra PROFINET-Switch FO Bedienungsanleitung

Helmholz

Helmholz Profinet 700-850-4PS01 Bedienungsanleitung

Helmholz

Helmholz 700-857-8PS01 Bedienungsanleitung

Helmholz

Helmholz 700-841-16S01 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch