Heritage Bathrooms Freestanding Baths Bedienungsanleitung
Installation Guide
Please keep this booklet for future
Reference.
Installer: when you have read these
instructions please ensure you leave
them with the user.
Freestanding Baths - Skirted Version
(Acrylic and Cast Iron)
02
Safety Notice 03
Installer Guidelines 04
Installation 05-10
Maintenance 11
Guarantee 12-13
Notes 14-15
Thank you for buying a Heritage Bathrooms Product.
When you buy one of our products, you can be condent that it not only features a beautiful, distinctive and
classical design, but that it has also been made to the very highest quality standards.
To ensure that it serves its purpose correctly, it needs to be tted correctly, preferably by a competent
plumber who has experience of tting bathrooms.
These tting instructions have been created to give you all the necessary information you will need to install
the product, but, if you need any further information or help, please contact us by phone on
0330 026 8503.
Introduction
Contents
03
Safety Note
Please make sure you read these instructions and retain for future use.
All products manufactured by Heritage Bathrooms are safe, providing they are installed and used correctly
and also receive maintenance when needed.
Baths, including the connecting water and waste system need to be installed in accordance with and meet
the requirements of the water supply regulations 1999 (Water Fittings) and Scottish By-laws 2004.
If you are in doubt about your ability to install this product correctly or safely, you should employ the
services of an experienced qualied plumber.
This product must not be modied in any way otherwise this will invalidate the guarantee.
Consider the following whilst using power tools:
• Prior to drilling into walls, check there are no hidden electrical cables or wires and there are also
no water pipes.These can potentially be found using an electrical or metal detector.You may
also need to know some of the schematics of previous installations to determine the suitability and
accommodation of the installation.
• Wear the correct PPE, especially ear, eye and hand protection when using power tools.
Unplug any mains equipment after use.
• Keep electrical equipment away from sources of water.
• If a blow-lamp is used when plumbing, the ame must be kept well away from the bath otherwise
damage may occur.
Cast Iron Baths are very heavy, a lifting aid or second person at minimum will be required to
manoeuvre.
Do not stand in the bath until the installation has been completed.
When making joints on baths (including the water and waste supplies), only use the washers provided and an
approved joining compound, where you nd it hard to make sound joints. When installing xtures on baths,
avoid excessive force when tightening plastic nuts.
Please ensure that the installation and accommodation is designed with future serviceability of the product
in mind. In the event a future claim is made under the product warranty, the design of the installation may
affect compensation costs if it has not been considered in the original design. It is strongly advisable to t
isolation valves before the baths water xtures in case isolation is required at any point during maintenance.
Failure to observe crucial information in these tting instructions will nullify your guarantee.
This product requires experience within plumbing. No responsibility will be taken for poor workmanship
resulting in leaks and injuries.
This bath is not designed to be tted by a wall, the minimal clearance distance must be at least 50mm.
If you intend to t a skirted bath on a concrete oor, please be aware that on certain models, the space
between the waste opening and the oor may not be large enough to t a waste trap. This will mean you will
need to channel the waste below the concrete oor level, as seen on page 9 section 6.
04
Installation Guidelines
05
Installation
If the bath is being installed on a suspended wooden oor or non-ground oor level, make suitable
provision to strengthen the oor. A structural engineer may be required to conduct a risk assessment.
Do not assume the oor is strong enough without making a suitable assessment.
1
Peel back the protective coating around the untted openings, where applicable. To prepare the bath, place
it face up on a dust sheet or protective blanket to prevent damage to the visible areas of the bath.
Do not stand in the bath during the installation.
2
Caution - Check ceiling strength
Protective lm removed
around openings
06
Installation
Waste Selection:
Refer to the installation supplied with the waste parts (where applicable).
Double Skin/Integrated Overow: The overow system will be built into the double skin of the bath. You
will need to purchase a suitable trap and exible tube to connect the the waste collection pipe.
Single Skin/External Overow: You will need to install a waste and overow to these baths which will
mean elevating high enough to reach underneath.
We recommend for ease of installation to couple the bath trap to the waste pipework using a exible
40mm waste hose, ensuring that clearance of waste is made by cutaways of beams and ooring.
Make sure supply pipework is suitably positioned so the oor mounted bath taps can be installed
in the nal positions.
3
4
Bath footprint
Drain hole
View of underside of bath
07
Installation
Heritage Bathrooms Acrylic and Cast Iron Skirted Baths come with the feet already installed.To get a
totally level bath which is required later in the installation, the feet will need to be adjusted.To do this
use a spirit level on the sides of the bath and use the adjusters on the feet (A-B) to make the bath level.
Note: On some cast iron baths, there will be no feet and the bath will sit on a formed base, the method
of levelling these baths is via four bolts underneath.
5
Minimum 5mm
Installation (Based on a wooden or suspended floor)
08
The use of a exible 40mm waste pipe may be needed once a suitable bath waste trap is tted.
Beware, the underside of this type of bath is limited for space and the way pipework can
be laid out.
Permanently connect waste and check for leaks by putting some water in the bath and letting it drain.
NOTE: IF your oor is concrete, please refer to the opposite page
6
7
Flow Flow
Flow
Waste trapdoor or hole
Inspect all joints for leaktightness
make sound where necessary
Floor level
09
Installation (Based on a concrete floor)
Channelling will be required for a concrete oor. The only way to avoid this is to build a suspended oor.
Connect the bath waste trap to the 40mm channeled pipe using a exible 40mm waste pipe.
Permanently connect waste and check for leaks by putting some water in the bath and letting it drain.
6
7
Flow Flow
Flow
Concrete channel for
40mm waste pipe
Inspect all joints for leaktightness
make sound where necessary
Floor level
10
Installation
Use a suitable bonding agent (not supplied) and apply to the strengthening bars on the underside of the
bath. This will stick the bath to the oor.
Caution must be used to make sure the waste is leaktight at this stage.
8
Inhaltsverzeichnis
Andere Heritage Bathrooms Badewanne Handbücher
Beliebte Badewanne Handbücher anderer Marken
Lyons
Lyons Elite ETLxx663219 Series Bedienungsanleitung
Woodbridge
Woodbridge BJ500 Montageanleitung
Whirlpool
Whirlpool Ariel ARL-702 Bedienungsanleitung
TEIKO
TEIKO EXCELLENT DUO Bedienungsanleitung
American Standard
American Standard Colony 5-1/2' x 32" Bedienungsanleitung
American Standard
American Standard 3052OD.X0X Kurzanleitung
