HEX-BEAM SP7IDX MARK IV HD Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere HEX-BEAM SP7IDX Antenne Handbücher

HEX-BEAM SP7IDX

HEX-BEAM SP7IDX MARK III HD Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung

HEX –BEAM SP7IDX TECHNOLOGY

1

HEXBEAM MARK IV HD &

HEXBEAM MARK IV Light

Ver 01,04.020

HEX-BEAM SP7IDX TECHNOLOGY ANTENNA is a broad band hex antenna

operating in PLUG AND PLAY system, its assembly time is 1-1,5h for one person. Its

installation doesn't require any additional tuning. Thanks to its small and compact

structure its turning requires only a small light rotor. The antenna works properly

even when it's installed relatively low over the ground.

Both antennas are equipped with all parts, required for a one, five or

six bands beam in range from 6 to 20 meters. The HEXBEAM SP7IDX

TECHNOLOGY offers mounted on the ground gain for front –to –back huge

amplify. The antenna offers the same values as a full size YAGA antenna. Has

unique shape: is much smaller, stiffly and makes less noise than typical

beams, it is lighter, easier to montage.

Please see its possible assembly methods on:

http://sp7idx-hexbeam.eu/hexbeam/mounting-suggestion

The antennas are tested at 7,3m height with analyser RigExpert AA-

1000 + Keysight E5061B ENA Vector Network Analyzer

24,8 m AIRCELL 7 + RG400/U HEW-Kabel GmbH Germany Filial Nordic-

Örebro-Cable

Test connections conducted with transceiver SDR - Flex Radio

System 6600M + EXPERT ELEKTRONICS SunSDR2 DX

PA Team SPE EXPERT 1,3K + 2K

It is helpful if you completely read through the instructions a couple of time before

you start.

The antenna is assembled intuitively, but please READ the manual carefully.

Please pay special attention to the red inscriptions.

2

Parcel Arrived

HEX –BEAM SP7IDX TECHNOLOGY

3

PART LIST

Three types of spreders (poles)

6 pieces - small ones + kevlar lines with S-hooks (6x 1m diameter 12,7mm) #4/8

6 pieces - medium (6x 1,35m diameter 17mm) #5/8

6 pieces - large (6x 1,35m diameter 22mm) #6/8

4

this is not a damage or factory defect - it is only covered with a thin

transport foil and can be peeled off it is not a defect!

transport foil is only for transport and may after some time go away do not

worry about it!

HEX –BEAM SP7IDX TECHNOLOGY

5

Set of hol dres (wire cleat set):

Size 5 - 6 set

Size 7 - 24 set

Size 9 - 6 set

STORE + Insulating tape - 1 piece –(option) #2/8

Screw 8 x 20 - 4 pieces for hub clamp on rure with centerpost

6

HEX –BEAM SP7IDX TECHNOLOGY

7

Down centerhub - mast

8

HEX –BEAM SP7IDX TECHNOLOGY

9

6 sets of electric component (driven+reflector+spacer cords)

6-10-12-15-17-20m

#2/8

10

Center post + balun (option) -1set

#3/8