Hi-Flame HF-737U Bedienungsanleitung

Installation and Operation Instructions

for USA only Model: HF-737U

Cast Iron Freestanding Stove

（EPA Approved）

Conform to UL 1482 - 2010

Tested by Intertek

KINDLY SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Safety Notice

If this solid fuel room heater is not properly installed, a house fire may result. For your

safety and to reduce the risk of fire, follow the installation instructions. Contact local

building officials, fire officials or the authority having jurisdiction about restrictions and

installation inspection requirements in your area, including the need to obtain a permit.

Kindly save these instructions for future reference.

Tested to U.S. Standards: ANSI/UL 1482

VERY IMPORTANT

PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW

ROOM HEATER. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY

DAMAGE, BODILY INJURY, OR EVEN DEATH! FAILURE TO READ AND FOLLOW THESE

INSTRUCTIONS BEFORE YOU PROCEED MAY RESULT IN DAMAGE, VOIDING YOUR

WARRANTY.

DO NOT INSTALL IN A MOBILE HOME.

DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE.

DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR

ENGINE OIL.

HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.

CONTACT MAY CAUSE SKIN BURNS.

Please contact the Hi Flame® dealer in your area if you have any questions about your stove

that are not covered in this manual.

Proposition 65 Warning: Fuels used in gas, wood-burning or oil fired appliances, and the

products of combustion of such fuels, contain chemicals known to the State of California to

cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec.

25249.6

Introduction

Congratulations on purchasing a genuine Hi Flame®stove. When cared for properly, the high

quality, finely crafted cast iron stoves and fireplace inserts will offer many years of reliable

performance. This instruction manual has been developed to ensure optimum performance from

the Hi Flame®stove. It's very important that you thoroughly read and understand all instructions

before using your new stove or fireplace insert.

Table of Contents Page

VERY IMPORTANT .................................................................................................................. 1

Introduction ............................................................................................................................. 2

Sample of Label ....................................................................................................................... 3

Stove Safety ............................................................................................................................ 4

Check Building Codes.................................................................................................................5

Before Installing Your Stove .................................................................................................. 5

Adequate Air Provision …………............................................................................................... .. 5

Installation ................................................................................................................................5

Floor Protection ......................................................................................................................... 6

Installation Clearances .............................................................................................................. 7

Well Sealed Flue System .......................................................................................................... 8

Chimney Connector .................................................................................................................. 8

Chimney .................................................................................................................................... 9

Factory Built Chimney ..............................................................................................................10

Masonry Chimney ....................................................................................................................11

Masonry Fireplace ...................................................................................................................12

Combustible Wall Chimney Connector Pass-Throughs ............................................................13

Operating Your Stove ........................................................................................................... 14

Fuel ......................................................................................................................................... 14

First Operation of Stove .......................................................................................................... 14

Air Controls ..............................................................................................................…………. 14

Refueling ..................................................................................................................................15

Ash Removal and Disposal of Ashes ....................................................................................... 15

Overnight Burning ................................................................................................................... 15

Stove Maintenance ................................................................................................................ 16

Care of Fire Bricks .................................................................................................................. 16

Care of Glass and Replacement of Glass ................................................................................ 17

Replacement Parts ................................................................................................................. 17

Surface Finish ......................................................................................................................... 17

HF-737U Part List Diagram...................................................................................................... 18

HF-737U Part List.................................................................................................................... 19

Trouble Shooting .................................................................................................................. 20

Fire Not Burning ...................................................................................................................... 20

Glass Blackens ....................................................................................................................... 20

Smoke in Room ...................................................................................................................... 20

Fire Burning Too Quickly ......................................................................................................... 20

Chimney Fire .......................................................................................................................... 21

Specifications ........................................................................................................................ 21

Hi Flame America Warranty –Policy & Procedures............................................................... 22

Warranty Exclusions and Limitations ....................................................................................... 23

Sample of Label

Stove Safety

When properly maintained and operated your stove should give you many years of service.

However, there are important safety aspects of these products that you need to be aware of when

operating a wood stove.

1. Hi Flame recommends that you have your new stove installed by a professional installer of solid

fuel burning appliances.

2. If this room heater is not properly installed, a house fire may result. To reduce the risk of

fire, follow the installation instructions. Failure to follow these instructions may result in

property damage, bodily injury, or even death!

3. Avoid creating a low pressure condition in the room where the stove is operating.

Operating an exhaust fan or a clothes dryer could create a low pressure area, causing

poisonous gases to come out of the stove into the room.

4. Only use solid wood fuel. DO NOT USE CHEMICALS TO START THE FIRE. Never use gasoline,

gasoline-type lantern fuel, kerosene, charcoal, lighter fluid, naphtha, engine oil, or similar liquids to

start or ‘freshen up’ a fire in this heater. Keep all such liquids well away from the stove while it is in

use. Do not burn garbage in the stove.

5. The burning of wood gives off gases which can be extremely dangerous. The stove is designed

that, under normal operating conditions, these gases pass up the flue chimney system and cannot

escape into your home, however it is important that your flue system is properly installed and that

you check all joints regularly to ensure that there are no cracks or gaps. Check the door sealing rope

and replace when damaged. We recommend a smoke alarm be fitted in rooms where stoves are

installed. Do not use stove in a room where negative pressure conditions may occur such as

through the use of extraction fans, unless an adequate air supply into the room is ensured, as this

may draw air through the stove and cause products of combustion to escape into the room.

6. Creosote and soot may accumulate in your flue pipe and chimney. This may ignite, causing a

chimney fire. If you suspect a chimney fire, evacuate people from the building, close down the

air controls on the stove and call the Fire Department. To prevent accumulation of soot or

creosote, check flue and chimney regularly and clean as necessary. Good burning, hot stoves will

generally cause a lot less build-up than slow burning stoves. Likewise, dry wood will cause less

build-up than wet wood. We recommend a fire extinguisher be available where stoves are in

operation. In the event of a chimney fire, do not re-light the stove until it and the flue chimney system

have been thoroughly checked by fire officials and repaired as necessary.

7. Stoves get extremely hot and should not be touched when lit. When young children are in the

area, we recommend the use of a suitable fire guard around the stove. Always wear protective

gloves when reloading the stove.

8. Never over-fire your stove. If external parts of your stove are glowing red, then the stove is

over-firing and your draft settings should be reduced. Never use a fan to supply air to the stove or to

extract air from it.

9. All users of the stove should be aware of the contents of this manual. Please leave the manual

where it is accessible to stove users and do not allow anyone to use the stove that is unfamiliar with

its correct operation.

10. Never use the stove if any parts are missing or damaged. Only use genuine parts as

replacements. Never modify your stove.

11. DO NOT INSTALL IN A MOBILE HOME.

We hope you have many years of warmth and comfort from

your stove but please do so safely.

Check Building Codes

•When installing, operating and maintaining your stove, follow the guidelines presented in

these instructions, and make them available to anyone using or servicing the stove.

•Your city, town, county or province may require a building permit to install a solid fuel

burning appliance.

•In the U.S., the National Fire Protection Association's Code, NFPA 211, Standards for

Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances, or similar regulations, may

apply to the installation of a solid fuel burning appliance in your area.

•Always consult your local building inspector or authority having jurisdiction to

determine what regulations apply in your area.

Before installing your stove

You need to consider the following to ensure the safe operation of your stove:

•Provision of adequate air to support efficient combustion of the fuel

•A well-sealed flue/chimney system, herein after referred to as the "flue system"

•The protection of combustible materials in proximity to the stove

Adequate air provision

It is essential for the safe and efficient use of your stove that you provide an adequate air supply

when lighting a fire, especially if there are extraction units such as cooker hoods or clothes

dryers in the vicinity. Crack the door open a little and allow air to enter. Once the air in the stove

and the flue stabilize, you can then close the door of the stove. Failure to do so will mean that

fuel is burned inefficiently, causing smoke and blackening the glass and may also cause smoke

to come back into the room.

Installation

Unpacking and preparing your stove for installation:

1. Remove your stove from the outer packaging and place on floor. Please inspect stove and

check that it is not damaged in any way. Never attempt to use a stove that has been damaged.

2. Remove and check the following contents (spare parts found in ash pan):

•Instruction manual

•Glass clips - 2 pc plus 4 screws (M5 x 6)

•Wooden handle for ash door - 1 pc plus 2 screws (M8 x 100)

•Wooden handle for glass door and side door - 2 pc

•Ash pan & shovel - I pc each

•Operating tool - I pc

•Insulated mitten

3. Fix the flue collar on the outlet which you selected by using the M6*20 flat crosshead screw.

Ensure all seals are secure to prevent air leakage. If you choose the rear flue outlet, remove the

flue cover before fixing the flue collar.

4. Fix the black handle on the stainless steel door catch with the M8*90 bolt.

5. Keep the rest of the screws and Allen wrench for future use.

In the unlikely event that something is missing, please contact your dealer immediately.

The floor protection

If the stove is to be installed on a combustible floor, it must be placed on a non-combustible

hearth pad. In the USA, the floor protector must extend 8” beyond each side of the fuel loading

door and 16” to the front (18” to the front in Canada). (See fig. 4)

Floor protection under the stove must be a UL 1618 Type 1 Ember Protector composed of non-

combustible material for protection from radiant heat, sparks and embers.

Individual sections of floor protection must be mortared together to prevent sparks from falling

through to combustible materials. Any carpeting must be removed from under the floor

protection.

16”

In a rear vent installation the floor protection must also extend under the stovepipe and a

minimum of 2” (50mm) beyond either side of the pipe.

Installation Clearances

It is extremely important that you respect required installation distances and that you respect

local installation regulations. This is for your safety. The manufacturer is not responsible for the

product if it is not installed following these recommendations. These clearances may only be

reduced by means approved by the regulatory authority.

One necessary precaution when installing a wood stove is to leave sufficient space between the

stove (top, sides, back, front, and under stove pipes) and any other material that can catch fire.

The clearance from the top of the unit to the ceiling is 75" (190.5 cm). All other clearances are

found in the table below.

A combustible surface is anything that can burn (i.e. sheet rock, wall paper, wood, fabrics, etc.)

These surfaces are not limited to those that are visible and also include materials that are

behind non-combustible materials. If you are not sure of the combustible nature of a material,

consult your local fire officials.

Parallel Installation Corner Installation

Single wall

connector pipe

Double wall

connector pipe

A –Unit to back wall

11” (279 mm)

7” (178 mm)

B –Chimney Connector to back wall

13.5” (343 mm)

9.5” (241 mm)

C –Unit to side wall

10” (254 mm)

D –Chimney Connector to side wall

15.5” (394 mm)

E –Unit to corner wall

8” (203 mm)

5.5” (140 mm)

F –Chimney Connector to corner wall

14” (356 mm)

11.5” (292 mm)

Well sealed flue system

Only materials and items approved for solid fuel stoves should be used for your stove. Under no

circumstances should you use aluminum or galvanized steel pipes for your stove flue.

Always fit pipes with the narrow side down. This will allow any creosote to run down the inside

of the pipe and not to come out and cause an unsightly mess and possible fire hazard. All joints

in the flue system should be sealed with fire cement and/or an appropriate fire resistant rope or

gasket.

Pipe bends should be kept to a minimum and we do not recommend using more than 2 bends

on any installation. Flues must not pass through ceilings, floors, attics, roofs, or combustible

walls without adequate and approved insulation being provided to protect combustible materials.

The chimney and flue provide a means of taking combusted fuel from the stove, as well as a

draft to enable the stove to work. It is essential that the flue system is kept in good condition and

there are no breaks or cracks allowing contact with any other combustible materials of the

house. It is also essential that the flue system is kept clean and seals are maintained to ensure

the draft is not lost.

The open end of the flue system must be above the height of the apex of the building and any

other obstructions, such as trees, which are within 10 feet (3m) of the flue system. Failure to do

this will affect the efficiency of the stove and may cause down drafts, which will mean

dangerous products of combustion are emitted into room.

Under no circumstances should the flue pipe be less than 6" (152.4 mm) internal diameter.

Chimney connector

The chimney connector is a single walled pipe used to connect the stove to the chimney. For

use with the appliance, the chimney connector MUST be 6" in diameter, with a minimum

thickness of 24 gauge black steel or 26 gauge blue steel.

Aluminum and galvanized steel pipe is not acceptable for use with the appliance. These

materials cannot withstand the extreme temperatures of a wood fire and can give off toxic

fumes when heated.

Do not use the connector pipe as a chimney.

Each chimney connector or stovepipe section must be installed to the stove flue collar and to

each other with the male (crimped) end toward the stove. See fig 5.

Fig. 5

This prevents any amount of condensed or liquid creosote from running down the outside of the

pipe or the stovetop. All joints, including the flue collar connection, must be secured with three

sheet metal screws to ensure that the sections do not separate.

For the best performance, the chimney connector should be as short and direct as possible,

with no more than two 90° elbows. The maximum horizontal run is 36" (91.44 cm) and a

recommended total length of stovepipe should not exceed 10 feet (3m). Always slope horizontal

runs upward ¼" (6.35mm) per foot toward the chimney.

No part of the chimney connector may pass through an attic or roof space, closet or other

concealed space, or through a floor or ceiling. All sections of the chimney connectors must be

accessible for cleaning. Where passage through a wall or partition of combustible construction

is desired, the installation must conform to National Fire Protection Association (NFPA) 211,

and is also addressed in this manual.

Chimney

•DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

•DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

This room heater must be connected to a 6" (152.4mm) factory-built UL 103 HT chimney or a

code-approved masonry chimney with a flue liner.

Chimney Height

A masonry chimney or a listed factory-built chimney must be the required height above the roof

and any other nearby obstructions. The chimney must be at least 3 feet (91 cm) higher than the

highest point where it passes through the roof and at least 2 feet (61 cm) higher than the

highest part of the roof or structure that is within 10 feet (305 cm) of the chimney, measured

horizontally.

Inhaltsverzeichnis

Beliebte Freistehender Ofen Handbücher anderer Marken

Hotpoint

Hotpoint CH60DHKFS Bedienungsanleitung