High Sec Labs FICE11PH-M Bedienungsanleitung

Models:

FICE11PH-M - DP/HDMI Secure Copper KVM Extender

FVCE11PH-M - DP/HDMI Secure Copper Video Extender

FIFE11PH-M - DP/HDMI Secure Fiber KVM Extender

FVFE11PH-M - DP/HDMI Secure Fiber Video Extender HDC19956 Rev. 3.4

SECURE KVM EXTENDERS | QUICK SETUP GUIDE

HSL Secure Extended Isolators Quick Setup Guide

TABLE OF CONTENTS

SECTIONS

Table of Contents 123

Introduction .......................................................... 2

HSL Secure KVM Extenders Family ............................................2

Installation............................................................ 3

Operation............................................................. 7

Running an EDID Capture .....................................................7

Safety and Regulatory Statements..................................... 8

HSL Secure Extended Isolators Quick Setup Guide

INTRODUCTION

SECTIONS

Table of Contents 2 3

HSL Secure KVM Extenders Family

The Secure KVM Extender extends video, audio and Keyboard/Mouse

signals up to hundreds of meters while it prevents vulnerable peripherals

from mediating between compromised and secure computers by

ensuring that video, audio and KM flow are in a single direction.

Up to 100 m

(COPPER)

Up to 10 km

(FIBER)

Display or Projector

Transmitter

Video

USB KB

& Mouse

Reciever Audio

RS232

Controller

Computer

or Matrix

Video

Audio

USB KB

& Mouse

HSL Secure Extended Isolators Quick Setup Guide

INSTALLATION

SECTIONS

Table of Contents 1 3

Step 1 – Connect the Secure KVM Extender’s Receiver and the

Transmitter parts

The device’s Receiver and Transmitter may be located in different

rooms or even different buildings.

Connect the two parts with a suitable cable through the connection

port:

•Models FICE11PH-M, FVCE11PH-M and FICE11CH-M - with a

Copper Cable

•Models FIFE11PH-M and FVFE11PH-M - with Optical Fiber Cable

Note: If either LED remains OFF, the Isolator does not recognize the

device. Use an alternative device! Transmitter

EDID LEDs

Receiver

KB/Mouse

LEDs

EDID LEDs

HSL Secure Extended Isolators Quick Setup Guide

INSTALLATION

SECTIONS

Table of Contents 1 3

Step 2 – Connecting the Transmitter (PC side) to the PC

1. Video connection: For all models, connect the PC to the Isolator

Extender’s VIDEO IN port, using the HDMI or DP video cable

2. PC Keyboard and Mouse connection: For FICE11PH-M, FIFE11PH-M

models, connect the PC to the Isolator using a USB A to USB B cable.

Connect the USB A end to the PC and the USB B end to the Isolator

Extender’s COMP/MOUSE port.

EDID LEDs

Video in Port

Host KB/Mouse

Power LED

Video Transfer

LED Rx to Tx

Connection LED

HSL Secure Extended Isolators Quick Setup Guide

INSTALLATION

SECTIONS

Table of Contents 1 3

Step 3 – Connecting the peripherals to the

Secure KVM Extender Receiver (CONSOLE SIDE)

1. Video connection: For all models, connect the monitor/projector

cable to the Isolator’s VIDEO OUT port.

2. PC keyboard and mouse connection: For FICE11PH-M, FIFE11PH-M

models, connect a USB mouse and keyboard, to the Isolator Extender

Receiver’s corresponding MOUSE and KB ports.

Both mouse and keyboard LEDs should light continuously green when

KB and Mouse are connected and device is turned on.

Note: If either LED remains OFF, the Extended Isolator does not

recognize the device.

Use an alternative device!

Rx to Tx

Connection LED

Video Transfer

LED

Power LED

EDID LED

EDID Lock

KB/Mouse LED

HSL Secure Extended Isolators Quick Setup Guide

INSTALLATION

SECTIONS

Table of Contents 1 3

Step 4 – Power ON

1. For all models, connect the power adapters on both the Secure

KVM Extender’s Transmitter and Receiver at the PC SIDE, DC IN port.

Power ON the unit by plugging it into an AC wall outlet.

2. The PC SIDE Power LED should light green continuously. If not, check

the connections.

Step 5 – Make sure the connected PC on the Transmitter side and

Display or Projector on the Receiver side are powered ON.

Power LED

HSL Secure Extended Isolators Quick Setup Guide

OPERATION

SECTIONS

Table of Contents 123

Running an EDID Capture

Before using the Extender, run a one-time EDID capture on both sides

– Transmitter and Receiver. This prevents the continuous transfer of

potentially malicious data - from the display to the PC – that could

infect the PC, cause data leakage, and so on.

Preparation:

•Connect the PC and all peripherals to both the units, according to

the Installation Instructions.

•Make sure the PC, display, and the units are ON.

To run an EDID capture:

1. On the Receiver, short-click the EDID Lock button. Wait 5 seconds

and then restart the unit, by unplugging the network cable and

power supply. At first, the EDID LED flickers for a few seconds and

then, once captured lights green continuously.

2. Make same on the Transmitter, short-click the EDID Lock button,

wait 5 seconds and then restart the unit. The EDID LED will now light

green continuously.

Note: If the EDID LED is OFF, check the connections and that the PC

or the Display are powered ON. Then, repeat the procedure.

3. Restart both units.

Note: An EDID capture needs to be performed for new installations

and when changing a display.

Transmitter

EDID LED

EDID Lock Button

Receiver

EDID LED

EDID Lock Button

HSL Secure Extended Isolators Quick Setup Guide

SAFETY AND REGULATORY STATEMENTS

SECTIONS

Table of Contents 123

Supported Hardware

This one or more of the following symbols may be included in your product

documentation and/or on the product.

Instructions: This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the product

user manual.

Dangerous Voltage: This symbol is intended to alert the user to the presence

of uninsulated dangerous voltage within the product’s enclosure that may be

of sufficient magnitude to constitute a risk of electric shock to persons.

Power On: This symbol indicates the principal on/off switch is in the ON

position.

Power Off: This symbol indicates the principal on/off switch is in the OFF

position.

Protective Grounding Terminal: This symbol indicates a terminal which must

be connected to earth ground prior to making any other connections to the

equipment.

Safety Precautions

WARNING: To avoid a potentially fatal shock hazard and possible damage to equipment,

please observe the following precautions.

•Instructions: Do not disable the power grounding plug. The grounding plug is an

important safety feature.

•Plug the power cord into a grounded (earthed) outlet that is easily accessible at

all times.

•Disconnect the power from the product by unplugging the power cord from

either the electrical outlet or the product. The AC inlet is the main disconnect for

removing power to this product. For products that have more than one AC inlet, to

remove power completely, all AC line cords must be disconnected.

•This product has no serviceable parts inside the product enclosure. Do not open

or remove product cover.

This product is for use with other products that are Listed or Certified by a Nationally

Recognized Testing Laboratory (NRTL).

NIAP Protection Profile

This product is compliant with the NIAP Protection Profile PSD version 4.0 certification

for peripheral sharing switch devices.

Installation Precautions

Note: HSL Secure Extended Isolators are protected with Holographic Tamper-Evident Labels

on the product’s enclosure to provide a visual indication in case the enclosure has been

opened or compromised.

Do not connect this product to computing devices that:

•are TEMPEST computers

•include telecommunication equipment

•include frame grabber video cards

•include special audio processing cards

WARNING: Peripherals’ Warning - For security reasons, this product does not support wireless

keyboards. It is recommended not to connect a microphone or headset to the audio output port.

Security Vulnerability

If you are aware of a potential security vulnerability while installing this product,

contact Technical Support immediately by:

•Web form: www.highseclabs.com/support/case/

•Email: security@highseclabs.com

•Tel: +972-4-9591191/2

WARNING: Unit Enclosure Warning - If the unit’s enclosure appears disrupted or if all LEDs flash

continuously, remove the product from service immediately and contact Technical Support.

Images for demonstration purposes only. This document may contain confidential and/or proprietary information of HSL Corporation, and its receipt or possession does not convey any

right to reproduce, disclose its contents, or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from HSL Corporation

is strictly prohibited.

Highseclabs.com

Andere Handbücher für FICE11PH-M

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere High Sec Labs Extender Handbücher