Hills DY6 Bedienungsanleitung

Digital Antenna

Installation Instructions

Models:DY6,Y3FM

*Note - some views not representative of all models.

Carefully remove the antenna from its packaging.

2 Unfolding the Antenna.

Starting at the back of the antenna and working towards the front... grasp

eachelement close to the pivot point (within 300mm) androtate outwards

until it clicks firmly into place. (see Figure1)

FIGURE 1

TOWARDS TRANSMITTER

Back Front

3 Loose Element Assembly.

*Note: Excludes Y3FM model.

Removetheloosestraightelementsfromantennaalongwith

the screws, nuts & insulators from the accessory bag.

ForDY models:Positionshortelementatfront&long

element at back, (see Figure1).

Forallothermodels:Positionlooseelementat front

of antenna, (see Figure1).

Place screw through the element, insulator & boom,

affix and tighten the nut, (see Figure 2).

FIGURE 2

Boot Preparation.

The boot has been designed to suit various sizes

of cables. For RG59 cable no trimming is necessary.

But for other cables trimming is required to suit. Refer

to Figure 3 showing appropriate positions for trimming

for correct coax cable type. When trimming boot

ensure a neat fit around cable to minimise water ingress

RG6 QUAD

FIGURE 3

Coax Cable Connection.

Slide the rubber boot provided down the

Coax Cable then fit the F Type connector

to the end of the Cable.

NOTE: the F type connector is not provided and

will depend upon the type of Coax Cable used.

(see Figure 4).

Pull enough cable through to reach

the balun housing and screw on connector.

Note: do not over tighten F Type connector.

Slide the boot down the Coax Cable into the

housing to cover the F connector. (see Figure 4)

FIGURE 4

Mounting the Antenna.

Check and ensure all fasteners are tight before mounting the antenna.

Assemble the mounting bracket and slide on to the boom. Loosen the flange nuts

sufficiently to allow the mast to fit between the tilt bracket and the U bolt.

Slide the antenna over the mast and tighten the nuts finger tight. (see Fig. 5)

Make sure balun housing is on the bottom side of the antenna. (see Fig. 6)

Aim the antenna towards the transmitter and tighten the nuts with a spanner.

Secure the cable to the mast with suitable fasteners such as cable ties or tape.

INSTALLATION TIPS : For best results mount the antenna outdoors, clear of any

obstructions and in line of sight with the transmitter.

TOP

FIGURE 5 FIGURE 6

RG6 DUO

RG59

Balun Housing

Avoid sharp bends

in the Coax Cable

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hills Antenne Handbücher

Hills

Hills TRU-BAND RB31160 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung