Hioki 3640-20 Bedienungsanleitung
INSTRUCTION MANUAL
For...は専用機種。複数の場合は「/」で区切る。
不要の場合はとる。
形名を入力。 複数の場合は「/」で区切る。
3640-20
品名を入力。
LUX LOGGER
Contents
Introduction i
Inspection ii
Safety Notes iii
Notes on Use v
Measurement Flow Chart and Reference Guide vi
Chapter 1 Product Overview 1
1.1 Name and Functions of Parts 2
1.2 Interval and Maximum Recording Time 3
Chapter 2 Set Up 5
2.1 Replacing the Battery 5
2.2 Power Save Function 7
2.3 Setting Current Time 8
2.4 Connecting 9662 LUX SENSOR 9
Chapter 3 Settings 11
3.1 Setting Items 11
3.2 Manual Setting 14
3.3 Setting by COMMUNICATION BASE 16
Chapter 4 Specifications 19
Chapter 5 Reference 21
5.1 Recommended Levels of Illumination 21
5.2 Relative Spectral Response Characteristics
in the Visible Spectrum 23
5.3 Angled Incident Light Characteristics 24
Chapter 6 Maintenance and Service 25
i
_____________________________________________________________________
Introduction
______________________________________________________________
Introduction
Thank you for purchasing this HIOKI "3640-20 LUX
LOGGER." To get the maximum performance from the
unit, please read this manual first, and keep this at hand.
ii
_____________________________________________________________________
Inspection
______________________________________________________________
NOTE Testing monitor batteries installed in the unit may possibly be
weak. Replace batteries before extended measurement usage.
Ins
p
ection
When the unit is delivered, check and make sure that it has
not been damaged in transit. If the unit is damaged, or fails
to operate according to the specifications, contact your
dealer or HIOKI representative.
Accessories
9662 LUX SENSOR
Instruction Manual
LR03 alkaline battery X4 (built into this unit, for monitor)
Before using the product the first time, verify that it
operates normally to ensure that the no damage occurred
during storage or shipping. If you find any damage, contact
your dealer or Hioki representative.
iii
_____________________________________________________________________
Safety Notes
______________________________________________________________
DANGE
R
This equipment is designed according to IEC 61010-1
Safety Standards, and has been tested for safety prior
to shipment. Incorrect measurement procedures
could result in injury or death, as well as damage to
the equipment. Please read this manual carefully and
be sure that you understand its contents before using
the equipment. The manufacturer disclaims all
responsibility for any accident or injury except that
resulting due to defect in its product.
Safety Symbols
This symbol is affixed to locations on the equipment
where the operator should consult corresponding topics
in this manual (which are also marked with the
symbol) before using relevant functions of the
equipment.
In the manual, this mark indicates explanations which it
is particularly important that the user read before using
the equipment.
Indicates DC (Direct Current).
Safet
y
Notes
This Instruction Manual provides information and warnings
essential for operating this equipment in a safe manner and
for maintaining it in safe operating condition. Before using
this equipment, be sure to carefully read the following
safety notes.
iv
_____________________________________________________________________
Safety Notes
______________________________________________________________
DANGE
R
Indicates that incorrect operation presents extreme
danger of accident resulting in death or serious injury
to the user.
WARNING
Indicates that incorrect operation presents significant
danger of accident resulting in death or serious injury
to the user.
CAUTION Indicates that incorrect operation presents possibility
of injury to the user or damage to the equipment.
NOTE Denotes items of advice related to performance of the
equipment or to its correct operation.
f.s. (maximum display or scale value, or length of scale)
Signifies the maximum display (scale) value or the length
of the scale (in cases where the scale consists of unequal
increments or where the maximum value cannot be
defined).
In general, this is the range value (the value written on
the range selector or equivalent) currently in use.
rdg. (displayed or indicated value)
This signifies the value actually being measured, i.e., the
value that is currently indicated or displayed by the
measuring instrument.
dgt. (resolution)
Signifies the smallest display unit on a digital measuring
instrument, i.e., the value displayed when the last digit on
the digital display is "1".
The following symbols are used in this Instruction Manual
to indicate the relative importance of cautions and
warnings.
Accuracy
The specifications in this manual include figures for
"measurement accuracy" when referring to digital
measuring instruments, and for "measurement tolerance"
when referring to analog instruments.
v
_____________________________________________________________________
Notes on Use
______________________________________________________________
CAUTION Do not store or use the product where it could be exposed
to high temperature or humidity, or condensation. Under
such conditions, the product may be damaged and
insulation may deteriorate so that it no longer meets
specifications.
NOTE Attach the supplied light sensor cap to the detector and then
perform zero ajustment before measurement.
Do not store or use the tester where it will be exposed to direct
sunlight, high temperature, high humidity, or condensation. If
exposed to such conditions, the tester may be damaged, the
insulation may deteriorate, and the tester may no longer satisfy
its specifications.
The reference level as marked on the faceplate is the tip of the
light sensor.
Notes on Use
In order to ensure safe operation and to obtain maximum
performance from the unit, observe the cautions listed
below.
vi
_____________________________________________________________________
Measurement Flow Chart and Reference Guide
______________________________________________________________
Is there sufficient
battery charge remaining
to o
p
erate 3640-20?
Replace batteries
Setting current time
See 2.1.
Connecting sensor See 2.4.
Set current time when using 3640-20 for the
first time or re
p
lacin
g
batteries. See 2.3.
Zero ajustment See 2.4.
Setting 3640-20
stand-alone
・Interval
・Range
Setting 3640-20
with COMMUNICATION
BASE
・Interval
・Current time
・Start control
・Recording method
Setting 3640-20 with
COMMUNICATION BASE
and PC
・Interval ・Current time
・Start control ・Range
・Recording method
・Comment
See 3.2.
Press REC/STOP
button to start
measurement.
Settin
g
start control
Start control o
p
tions
No
Yes
Quick start
Prescheduled start
Starts measurement
immediately.
Starts measurement at
prescheduled time.
Setting
recordin
g
method
Endless
One time
When recording data
reaches 32000
measurement stops.
When recording data exceeds 32000, it overwrites
previously recorded data.
Press REC/STOP button to stop measurement.
After measurement is complete, disconnect sensor. Use COMMUNICATION BASE to
send measurement data to personal computer. (See COMMUNICATION BASE
instruction manual.)
See 3.2.
Measurement Flow Chart and Reference Guide
Inhaltsverzeichnis
Andere Hioki Datenlogger Handbücher
Hioki
Hioki LR8431-20 Bedienungsanleitung
Hioki
Hioki HiLogger 3145-20 Bedienungsanleitung
Hioki
Hioki LR8431-20 Bedienungsanleitung
Hioki
Hioki LR8401-20 Bedienungsanleitung
Hioki
Hioki PW3365 Bedienungsanleitung
Hioki
Hioki LR8431-20 Bedienungsanleitung
Hioki
Hioki 8860-50 Bedienungsanleitung
Hioki
Hioki lr5001 Bedienungsanleitung
Hioki
Hioki PW3360-30 Bedienungsanleitung
Hioki
Hioki 3638-20 Bedienungsanleitung
Hioki
Hioki 3645-20 Bedienungsanleitung
Hioki
Hioki HiLogger 3145-20 Bedienungsanleitung
Hioki
Hioki LR5011 Bedienungsanleitung
Hioki
Hioki 3910-20 Bedienungsanleitung
Hioki
Hioki 8423 Bedienungsanleitung
Hioki
Hioki LR8400-20 Bedienungsanleitung
Hioki
Hioki LR8410-20 Bedienungsanleitung
Hioki
Hioki 8861 Gebrauchsanweisung
Hioki
Hioki LR5051-20 Bedienungsanleitung
Hioki
Hioki LR8450 Bedienungsanleitung
