Hisense Laser TV Display Screen Bedienungsanleitung
INSTALLATION GUIDE
Before you install this product, read this guide completely and
make sure you understand all of the content.
Hisense Laser TV Display Screen
ENGLISH
ES-G1835M8
1
The Hisense Laser TV Display Screen has a bezel trim and is designed to be used in rooms where the ceiling light cannot be
moved.
Product Description
Dust, dirt and scratches on the screen will affect how images appear. Follow the instructions below to properly maintain the
screen.
1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular motion.
Wipe from left to right only.
2) Clean the dust on the screen surface with a soft brush or microfiber cloth. A rough towel or cloth might damage the surface.
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.
IMPORTANT:
Take heed to the following precautions at all times in order to avoid damaging the
screen. It is not covered under warranty.
• Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.
• Don’t scratch the material, as it will leave permanent markings on the screen’s surface.
• Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the material.
• Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such chemicals
will permanently damage the screen.
Maintaining the Screen
Required Tools to Install the Screen
Tape measure Stud nder Level Pencil
Screwdriver with 5/16"(8mm)
drill bit for wood stud
Hammer for concrete Phillips screwdriver Tape
anchors
Hardware and Parts List for Screen Mounts
ST5.5x70 Screws (x4) M3x6 Screws (x6)
Drill bolt 8 x 60,
Polyamide 6 (PA6) (x4)
Bracket wands (x2)
460mm
Bracket wands (x2)
500mm
Handle (x2)
Hanging component (x2)
Velcro strips (x4)
Bracket wands (x2)
269mm
Paper template (x1)
2
Hardware and Parts List for Screen
Make sure you have all of the parts shown below before you begin the installation procedure.
No. Name Picture Qty. No. Name Picture Qty.
A
Elbow Joints
(the side with an arc
edge is front)
8 B
Horizontal Frame
(Spring inserted into the
frame already)
1
C
Left/Right Vertical
Frame(Spring inserted
into the frame already)
2 D1 Vertical Edge Trim
(short) 2
D2 Top Edge Trim
(long) 1 D3 Bottom Edge Trim
(long with logo) 1
EUpper Frame
Assembly 1 F Bottom Frame 2
G M3x6 Screws 20 H M5x6 Screws 32
I
ST5.5x70 Screws
(from the hardware
and parts list for screen
mounts)
4 J M5x14 Screws 4
K Spring Hook 2 L1 Long Fiberglass Rod 2
L2 Short Fiberglass Rod 2 M Corner Sleeve 4
NWhite Gloves
(for screen installation) 4 O Cloth Liner
for Assembly
1
PStarBright CLR®
Material
1 Q Support Rod 1
3
Place the Cloth liner(O) sponge on clean area on the ground to assemble the screen.
1. Insert the bottom beam(F) into the bottom horizontal frame(B) as shown below to the position between two location labels
and fasten the M5x14 Screws (J).
2. Insert the elbow joint (A) (front side is up))into each end of the horizontal frame (B) and upper frame assembly (E) as
shown below.
B
B
F
F
B
FJ
J
J
J
B
F
A
Sliding chute 2
Sliding chute 1
B/E
AA
B/E
AA
ASectional view of B/E
Frame Assembly
Note:
The installation space should be at least 5m x 3m( 196 7/8 inches x 118 1/8 inches).
≥5m (196 7/8 inches)
≥3m (118 1/8 inches)
F
4
3. Insert the two vertical short frames (C) into the elbow joint (A) as shown in the diagram below.
4. Next, fasten the four angles with the M5x6 Screws (H).
B(A)(A)
(A) (A)
E
CC
E
AA
CC
(A)
(A)
E
E(A)(A)
C
C
B
A
A
C C
Make sure all four corners are
properly in place to form a
perfect square.
M5x6 Screws
(H) H
HA
A
A
A
5
Please read this important note before proceeding with the installation process of the material:
Before handling the StarBright CLR® material(P), put on the supplied pair of white gloves(N) to avoid leaving
fingerprint marks, dust or oil from your hands on the surface of the material(Figure 1). The StarBright CLR®
material(P) is very delicate and should be handled with extreme care. Do not allow the material to fold or bend.Failure
to follow instructions will result in permanent damage to the screen material, which is not covered by warranty.
1.
Remove the StarBright CLR® material(P) from the packaging tube and set it gently on a clean surface.
Tip: Carefully put a small flat weighted object at the edge to prevent it from moving out of place.
Please keep the front of the material face down.
2. It is strongly recommended for two people to unroll the material to prevent the screen from bending or rolling unevenly.
Each person should hold one end of the roll and slowly unroll the screen in a clockwise direction (Figure 2). Tip: Check the
DOWNSIDE label on the material.
3. Lay the material completely flat with the front facing down on a clean surface in a horizontal position (Figure 3)
4. Insert the long and short fiberglass rods (L1,L2) through the openings. The long fiberglass rods(L1) are used on the
vertical edges of the screen material, and the short fiberglass rods(L2) are used on the horizontal edges, as shown
below.
5. Carefully and gently place the assembled frame on top of the screen material.Align the screen material corner with the
corner of assembled frame as the diagram below. In order to avoid puncturing the material, do not allow the angled edge of
the frame to come in direct contact with the screen.
Back side of material
Front side of
material
Figure 3
Screen on a clean cloth
in a horizontal position
DOWNSIDE
Figure 2
Back side of material
Figure 1
L1
L1
L2 L2
Screen Material Installation
6
6. With one of the springs securely inside the groove of the frame, use the spring hook(K) to attach the spring to the hole
located on the outer edge of the screen material.
1) Attach the four corners first. Two people should use the spring hook (K) to attach the spring to the hole located on the
screen material’s outer edge in the order of 1-1→2-2→3-3→4-4, then 5-5→6-6→7-7→8-8,
Correct material corner installation:
E
Tip:Make sure the back of the screen material is facing
up as shown in this illustration.
B
Fcomponent of B and F
12
6
5
8
2 3 4
8
7
5
6
4
3
1
7
Step ①Step ②
Step ③
Step ④
Spring Hook(K)
Align the corner
E
component of B and F
Top
down
Fiberglass Rod(L)
StarBright CLR®
Material(P)
7
2) After you’ve installed the corner of the material, assemble the spring in the order ①→②shown below.
Stretch the screen material in the
direction of the arrowhead.
Use the spring hook (k) to attach the
2 springs to the hole located on each
side of the screen material’s outer
edge.
Repeat until all of the springs are
installed.
①
①
① ①
②
②
②
②
②
② ②
②
8
Edge Trim Installation
1. Place the Edge Trim(D) along the four edges of the screen material corner. (Note: The logo should be positioned on the
bottom frame).
2. Place all the trim pieces along the edge of screen material. Adjust the trim so that the top and bottom trim pieces are
touching and show no gaps in the center. Align the M3x8 Screws(G) with hole B as shown in the illustration below. Next,
insert the screws in B tightly. (Note: When installing edge trim, do not install the screen protective paper, foam, nonwovens
or other materials into the screen edge.)
Correct Edge Trim corner installation:
Align the Edge Trim(D) with the Frame corners and the holes.
3. Place the corner sleeve(M) on the four corners. When the corner sleeve(M) fits the edge trim(D) completely, then tighten
the screws into hole A .
A
B
Edge Trim(D) StarBright CLR® Material (P)
M3x8 Screw(G) of B
Sectional view
M3x6 screw(G) of A
Screen back side Screen back side Screen front side
M
D1 D1
D3(with logo)
D2
Top
down
9
4. Slant the support rod and make it clip into the groove of upper and bottom frames. Make one end of the rod stay still and
push the other end to the center until support rod is perpendicular to the frames.
5. Look down on the screen, if the material is black it is in the correct direction and ready for mounting on the wall. However, if
the material is white, turn around the screen and then install it.
When you are nished, the front and back of the screen should appear as shown below.
Push
Ending condition
Initial condition
Front side Back side
Logo on Bottom Edge Trim
NOTE:
There are also "Top" and "Bottom" labels on the back of the screen material to help distinguish the correct
direction. Please make a note of this.
Inhaltsverzeichnis
Andere Hisense Monitor Handbücher
Hisense
Hisense HME8C32 Bedienungsanleitung
Hisense
Hisense HME8C55E Bedienungsanleitung
Hisense
Hisense HMC8C86TOA Bedienungsanleitung
Hisense
Hisense HMD6C30S Bedienungsanleitung
Hisense
Hisense 55SOA25PT Bedienungsanleitung
Hisense
Hisense HMC8C65TOA Bedienungsanleitung
Hisense
Hisense HMD4C27S Bedienungsanleitung
Hisense
Hisense HMD3C21S Bedienungsanleitung
Hisense
Hisense HAIO136 Bedienungsanleitung
Hisense
Hisense HMD2G21S Bedienungsanleitung
Hisense
Hisense 49WF Series Bedienungsanleitung
Hisense
Hisense HME8C58 Bedienungsanleitung
Hisense
Hisense HAIO138 Bedienungsanleitung
Hisense
Hisense 75B4E30T Bedienungsanleitung
Hisense
Hisense PDP4211AU Bedienungsanleitung
Hisense
Hisense 75B4E30T Bedienungsanleitung
Hisense
Hisense 65WR6CE Bedienungsanleitung
Hisense
Hisense Covidien HME2C26 Bedienungsanleitung
Hisense
Hisense 65WR6BE Bedienungsanleitung
Hisense
Hisense HMD3G21S Bedienungsanleitung
