Hitachi Highly WHP13300PSDPC8FQ Bedienungsanleitung

Highly

Rollkolbenverdichter

Rotary Compressors

Spezifikation

Installation Manual

RIES GmbH, Rudolf-Diesel-Str. 10, D 64569 Nauheim, GERMANY

Phone: +49 6152 9741 0, Fax: +49 6152 9741 21, Email: [email protected], Website: www.ries-gmbh.de

R 290

54,8 cm3/rev

900 - 6600 min-1

WHP13300PSDPC8FQ

DC / BLDC

CONTENTS

—————— 1～4

WHP13300PSDPC8FQ SPECIFICATION

1.SCOPE

2.SPECIFICATION OF THE MODEL

3.THE PARAMETER OF MOTOR

4.CHARACTERISTICS

5.PARTS AND DRAWING LIST

————— 5～15

HEAT PUMP Compressor CRITERIA

———— 16

CHECK UPON DELIVERY

1.BASIS FOR CHECKING UPON DELIVERY

2.RULE FOR CHECKING UPON DELIVERY

—————————— 17～26

DRAWINGS

0——————————27~30

ATTACHED PAGE

—— 31

SPECIFICATION REVISION RECORD

SUBJECT

Model WHP13300PSDPC8FQ SPECIFICATION PAGE：1/31

1. SCOPE

This specification is applied to SHANGHAI HIGHLY Heat pump water heater compressor.

2. SPECIFICATION OF THE MODEL

Item Spec

2.1 Model Type WHP13300PSDPC8FQ

2.2 Power source input to inverter Rated voltage / Rated frequency/Phase

380V/50Hz/3ФOR 220V/50HZ/1Ф

2.3 Output 2630W(@3600 min-1)

2.4 Application Heat pump water heater

2.5

Performance

Item Rated Condition

Rotational speed 3600 min-1

Nominal Heating Capacity 13300W±5%

Motor input 2860W±5%

Current 11.5A±5%

COP(see*) 4.65±5%

Test Conditions

Evaporating temp. 7.2℃

Condensing temp. 54.4℃

Liquid temp. entering

expansion valve. 46.1℃

Return gas temp. 35℃

Ambient temp. 35℃

SUBJECT

Model WHP13300PSDPC8FQ SPECIFICATION PAGE：2/31

*.COP= Heating capacity (W)

Motor input (W)

*.Rated Capacity and input are measured with HITACHI inverter circuit by secondary Refrigerant

calorimeter Methods of JIS B8606 by SHANGHAI HIGHLY Electrical Appliances Co., Ltd.

2.6 Refrigerant R290

2.7 Displacement 54.8ml /rev（Double-cylinder

2.8 Allowable frequency range 900～6600 min-1

2.9 Oil HAF68 1150±20ml

2.10 Allowable amount of refrigerant

charge

Below 1500g

2.11 Hermetic Terminal Conventinal Type

2.12 Space volume of inner case 1500cm3

2.13 Compressor weight 18.9kg incl. Oil

2.14 Motor Type

Insulation class Direct current brushless motor E class

2.15

Compressor natural frequencies

19.9Hz/21.7Hz/24.5Hz±3Hz（should be avoided or

pass within ten seconds are compressor natural

frequencies, and they can be changed when connecting

with pipe lines. So, it is necessary to take the

piping stress of the system into account. The

recommended piping stress value

can be seen as follow，

When the system Start/stop：below 34.3N/mm2

When the system operating：below 17.7N/mm2

SUBJECT

SPECIFICATION

Model WHP13300PSDPC8FQ PAGE：3/31

Sheet 2

Sheet 3

4. CHARACTERISTICS

4.1 Appearance

The surface of the compressor is painted to black, without obvious flaw ,impact scar, paint peel

off, rust and so on.

3. THE PARAMETER OF MOTOR

3.1 Rotor Pole（Pole）4 ——

3.2 Rated Frequency Range（Hz）30-220

Electrical Frequency ， Relating to

VDCmax of Inverter

3.3 Demagnetizing Current（A）54.01A Peak Current，at 120℃，-5%

Demagnetizing Rate

3.4 Inductance Ld（mH） Sheet 2 ——

3.5 Inductance Lq（mH）Sheet 2 ——

3.6 Stator coil resistance

(20℃）（Ω）0.502（20℃） line-to-line

3.7 Voltage Constant（Vrms/krpm）43.10V/krpm line-to-line

3.8 Torque Constant（N·m/Ams）0.69 Torque/Current

力矩/电流

3.9 Inertia （Kg·m2）0.000666

3.10 Flux Φa（Wb）） 0.1702

φ(Per Phase，Peak)= 32

φ(一相 peak 值)= 32

3.11 Magnet Material NdFeB

Current 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

q 5.44 5.39 5.34 5.29 5.24 5.18 5.12 5.06 5.00 4.95 4.89 4.83 4.78 4.72 4.66

d 3.71 3.65 3.65 3.64 3.63 3.61 3.59 3.56 3.54 3.51 3.48 3.45 3.42 3.39 3.36

Running effectiv current（A）3 4 5 6 7 8 9 10

Running torque（N.m）2.1 2.8 3.4 4.1 4.8 5.5 6.2 6.9

SUBJECT

SPECIFICATION

Model WHP13300PSDPC8FQ PAGE：4/31

4.2. Indication

Compressor model type, manufacturing data are clearly indicated on the surface of compressor。

4.3. Residual moisture

Residual impurities

150mg MAX

4.4. 90mg MAX

5 PARTS AND DRAWING LIST

PARTS NAME QTY/SET DRAWING NO. REMARKS

Compressor 1 4CYCH0638 Dimensioned sketch

Mounting

Parts

Rubber grommet

Bolt

Nut

4CYC00643

4CYC00700

Electrical

Parts

hermostat

erminal cover

Gasket

Nut

Rubber washer

Sleeve

4CYC01403

4CYC00988

4CYC01047

3CYC00004

4CYC00174

4CYC01042

4CYC01272

Lead routing

Pressure guarantee

Chart

Pressure Guarantee

Range Chart

Notes for rotational

speed change

Performance curse

Appendix

*. Out of supply, for reference./ Nicht mitgeliefert- nur als Referenz

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

PAGE：5/31

COMPRESSOR CRITERIA

1 Strictly observe the specification

The compressor should be used in specifications written in this “compressor specification” and

not be used in specifications outside it.. The main circuit must link up with fuse or breaker.

2 Source voltage

Specified inverter is linked up with compressor terminals . Applied voltage of this inverter should

be voltage specified in this “compressor specification”. Alternating voltage should never be applied

on terminals (for example：commercial alternating voltage of 1φ100V,200V,3φ200V).This is because

that if applied alternating current the direct current motor will demagnetize.

3 Operating voltage range

The compressor should be operated in the range of rated voltage ±10% , under standard condition

and overload condition of rated frequency (applied voltage to inverter).It must be satisfied

with item 5 ,6,7.

4 Operating temperatures and pressures

The operating temperatures and pressures of a compressor should be within the range shown in

the table 2 and graph 1.

5Oil Back and height of the oil level

The oil should be returned continuously to the compressor and the structure of the refrigerating

system should not make oil stay in the system. The oil level in compressor should be satisfied

with chart 2.If not keep the oil level, the shortage will occur, and influence the reliability of

the compressor.(please check the oil level in the compressor with the sight glass which supplied

form SHEC.

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

热泵热水器专用压缩机使用基准 PAGE：6/31

There should be superheated gas returned to the compressor under all normal operating conditions.

Table 2

Item Operating Envelope

Discharge pressure

MPa

3.13 {30.91}MAX

（condensing temperature 80°C )

（see graph 1）

Suction Pressure

MPa

0.139~0.95 {0.40~8.67}

(Evaporation Temperature ：-35℃~25℃).

Compressor suction side can handle the same

maximum pressure as discharge side without

damage when compressor is not running.

Compressor case bottom

temp

99℃or below and 6 ℃ higher than condensing temperature，

（the time compressor case bottom temp 6 ℃below the condensing

temperature should be less than 5 minutes each time）,

Requirement for high pressure ratio condition can be seen on page

28.

Motor winding temp R.Voltage±10%: 120℃ MAX

Accumulator temp Higher than outlet pipe of evaporator

Ambient temp Meet for the condition of above mentioned motor winding

temp.

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

PAGE：7/31

Graph 1 图 1

P1 P2 P3 P4 P5 P6 P7 P8

Condensing temperature 70℃ 25℃ 10℃ 10℃ 65℃ 80℃ 80℃ 80℃

Evaporation Temperature 25℃ 25℃ 10℃ -35℃ -35℃ -10℃ -5℃ 15℃

*Requirement for high pressure ratio condition can be seen on page 28.

6 Current limitation

Current peak among motor terminals（include instantaneous current peak）should be

below demagnetizing current in order to prevent magnet in motor from demagnetization.

7 Pressure difference between suction and discharge 吸气、排气压力差

In all allowable rotational speed range, the difference of pressure should be more than

0.39MPa{4kgf/cm2}. But if there is no problem of noise when assembled in air conditioner,

it can also below this value(the requirement can be seen on page 28).

8 Discharge pipe temperature

Discharge pipe temperature is measured at a distance 300mm from the surface of compressor

and should be less than 110℃. The tip of the thermocouple is fixed by soldering when

measuring discharge pipe temperature .Furthermore, soldering point is covered with urethane

foam to prevent the effect of wind.

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

热泵热水器专用压缩机使用基准 PAGE：8/31

9 Dust of compressor hermetic terminals

Compressor hermetic terminals should be mounted with specified cover in right way to prevent

dust entering, and should be used in direction which dust is hard to enter in.

10 Lead wire of compressor hermetic terminals

Measuring the temperature of hermetic terminals , lead wire should be resist to the temperature

and be clamped so as not in touch with the surface of compressor and pipe.

11 Start-stop frequency

The frequency should be less than 6 times per hour. Operating time from start to stop should

be more than 3 minutes to make sure the oil is above the minimum level. Stopping time should be

more than 3 minutes to make sure the suction pressure and discharge pressure is balance.

12 Rate of rotational speed change

The rate of compressor rotational speed (acceleration) should be less than 133min-1/s as the

compressor speed is below 5400rpm while less than 60min-1/s as the compressor speed is higher than

5400rpm. However, when rotational speed is reduced to avoid temporary over-current， the rate

can also be less than 600min-1/s when the compressor speed is below 5400rpm and should be less

than 300min-1/s when the speed of compressor reach above 5400rpm，only if the variable range is

below 120min-1.

13 Air and moisture in refrigerating system

The degree of vacuum in refrigerating system should be less than 20Pa (150×10－3mmHg) at

room temperature just before charging refrigerant. The quantity of water should be less

than 0.15ml.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Luftkompressor Handbücher

Hitachi

Hitachi Highly WHP09100VUKPA8LT6 Bedienungsanleitung

Hitachi

Hitachi EC25E - Lon Wheelbarrow Air Compressor Bedienungsanleitung

Hitachi

Hitachi EC 2610E Bedienerhandbuch

Hitachi

Hitachi EC25E - Lon Wheelbarrow Air Compressor Bedienungsanleitung

Hitachi

Hitachi WHP09500AEDPC9EQ Bedienungsanleitung

Hitachi

Hitachi CA47TLA-D2PE3 Bedienungsanleitung

Hitachi

Hitachi Highly WHP07600PSDPC9KQ Bedienungsanleitung

Hitachi

Hitachi EC 10SB (SL) Bedienerhandbuch

Hitachi

Hitachi EC 6C Bedienungsanleitung

Hitachi

Hitachi Highly WHP05600VUKQA7JG6 Bedienungsanleitung

Hitachi

Hitachi NEXT Series Bedienungsanleitung

Hitachi

Hitachi EC 129 Bedienerhandbuch

Hitachi

Hitachi Highly WHP11500VSDPC9EQ Bedienungsanleitung

Hitachi

Hitachi EC6B Bedienungsanleitung

Hitachi

Hitachi NEXT Series Bedienungsanleitung

Hitachi

Hitachi HIGHLY WHP08750VCDNC9AU Bedienungsanleitung

Hitachi

Hitachi EC119SA - 15 Amp 2.5 HP Lon Twin-Stack Air... Bedienungsanleitung

Hitachi

Hitachi EC 28M Bedienerhandbuch

Hitachi

Hitachi EC1433H Bedienungsanleitung

Hitachi

Hitachi NEXT Series Bedienungsanleitung

Hitachi

Hitachi BEBICON SRL-5.5MB5A Bedienungsanleitung

Hitachi

Hitachi EC119 OM Bedienerhandbuch

Hitachi

Hitachi EC99S Bedienerhandbuch

Hitachi

Hitachi HISCREW 2000 Series Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung

Craftsman

Craftsman 919.152144 Bedienungsanleitung

Alkin

Alkin W3 Series Bedienungsanleitung

Fubag

Fubag F1 241/24 CM2 Bedienungsanleitung