Hitachi RAM-90QH5 Bedienungsanleitung

NO. 0371E

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

ROOM AIR CONDITIONER

OUTDOOR UNIT

APRIL 2007

Refrigeration & Air-Conditioning Division

SERVICE MANUAL

REFER TO THE FOUNDATION MANUAL

TECHNICAL INFORMATION

FOR SERVICE PERSONNEL ONLY

CONTENTS

SPECIFICATIONS ------------------------------------------------------------------- 5

INSTALLATION --------------------------------------------------------------------- 16

CONSTRUCTION AND DIMENSIONAL DIAGRAM --------------------- 20

WIRING DIAGRAM ---------------------------------------------------------------- 21

MAIN PARTS COMPONENT --------------------------------------------------- 24

CIRCUIT DIAGRAM --------------------------------------------------------------- 25

BLOCK DIAGRAM ----------------------------------------------------------------- 29

BASIC MODE ----------------------------------------------------------------------- 31

REFRIGERATING CYCLE DIAGRAM --------------------------------------- 51

DESCRIPTION OF MAIN CIRCUIT OPERATION ----------------------- 52

TROUBLE SHOOTING ----------------------------------------------------------- 88

PARTS LIST AND DIAGRAM -------------------------------------------------- 94

After installation

(W)

(A)

COOLING CAPACITY

DC INVERTER FIVE SYSTEM MULTI

TYPE

MODEL

POWER SOURCE

TOTAL INPUT

TOTAL AMPERES

SPECIFICATIONS

RAM-90QH5

HEATING CAPACITY

DIMENSIONS (mm)

NET WEIGHT

1ø, 220 - 240V, 50/60Hz

(kg)

(kW)

(B.T.U.)

REFER TO THE SPECIFICATIONS PAGE

OUTDOOR UNIT

RAM-90QH5

950

800

370

NOTE:

This manual describes only points that differ from

PM No. 0322E, PM No. 0355E and PM No. 0366E

for items not described in this manual.

– 1 –

SAFETY DURING REPAIR WORK

1. In order to disassemble and repair

the unit in question, be sure to

disconnect the power cord plug

from the power outlet before starting

the work.

2. If it is necessary to replace any parts, they should be replaced with respective genuine parts for the unit, and

the replacement must be effected in correct manner according to the instructions in the Service Manual of

the unit.

If the contacts of electrical parts

are defective, replace the

electrical parts without trying to

repair them.

3. After completion of repairs, the initial state

should be restored.

4. Lead wires should be connected and laid as

in the initial state.

5. Modification of the unit by user himself should

absolutely be prohibited.

6. Tools and measuring instruments for use in repairs or inspection should be accurately calibrated in advance.

7. In installing the unit having been repaired, be careful to prevent the occurence of any accident such as

electrical shock, leak of current, or bodily injury due to the drop of any part.

8. To check the insulation of the unit, measure the insulation resistance between the power cord plug and

grounding terminal of the unit. The insulation resistance should be 1M or more as measured by a 500V

DC megger.

9. The initial location of installation such as window, floor or the other should be checked for being and safe

enough to support the repaired unit again.

If it is found not so strong and safe, the unit should be installed at the initial location reinforced or at a new

location.

10. Any inflammable thing should never

be placed about the location of

installation.

11. Check the grounding to see whether

it is proper or not, and if it is found

improper, connect the grounding

terminal to the earth.

DANGER

First, I must disconnect

the power cord plug

from the power outlet.

–2 –

WORKING STANDARDS FOR PREVENTING BREAKAGE OF SEMICONDUCTORS

1. Scope

The standards provide for items to be generally observed in carrying and handling semiconductors in relative

manufacturers during maintenance and handling thereof. (They apply the same to handling of abnormal goods

such as rejected goods being returned).

2. Object parts

(1) Micro computer

(2) Integrated circuits (IC)

(3) Field-effect transistors (FET)

(4) P.C. boards or the like on which the parts mentioned in (1) and (2) of this paragraph are equipped.

3. Items to be observed in handling

(1) Use a conductive container for carrying and storing of parts. (Even rejected goods should be handled in

the same way).

Fig. 1. Conductive Container

(2) When any part is handled uncovered (in counting, packing and the like), the handling person must always

use himself as a body earth. (Make yourself a body earth by passing one M ohm earth resistance through

a ring or bracelet).

(3) Be careful not to touch the parts with your clothing when you hold a part even if a body earth is being

taken.

(4) Be sure to place a part on a metal plate with grounding.

(5) Be careful not to fail to turn off power when you repair the printed circuit board. At the same time, try

to repair the printed circuit board on a grounded metal plate.

Fig. 2. Body Earth

Body earth

(Elimik conductive band)

Clip for connection with a

grounding wire

A conductive polyvinyl bag IC

Conductive sponge

–3 –

(6) Use a three wire type soldering iron including a grounding wire.

Bare copper wire (for body earth)

Working

table

Resistor of 1 M (1/2W)

Earth wire

Fig. 3. Grounding of the working table

Screw stop at the screwed

part using a rag plate

Soldering iron

Grounding

wire

Fig. 4. Grounding a soldering iron

Use a high insulation mode (100V, 10M or higher) when ordinary iron is to be used.

(7) In checking circuits for maintenance, inspection or some others, be careful not to have the test probes of the

measuring instrument shortcircuit a load circuit or the like.

Metal plate (of aluminium, stainless steel, etc.)

Staple

–4 –

1. In quiet operation or stopping the operation, slight flowing noise of refrigerant in the refrigerating cycle is

heard occasionally, but this noise is not abnormal for the operation.

2. When it thunders near by, it is recommend to stop the operation and to disconnect the power cord plug

from the power outlet for safety.

3. The room air conditioner does not start automatically after recovery of the electric power failure for

preventing fuse blowing. Re-press START/STOP button after 3 minutes from when unit stopped.

4. If the room air conditioner is stopped by setting the temperature, or missoperation, and re-start in a moment,

there is occasion that the cooling and heating operation does not start for 3 minutes, it is not abnormal

and this is the result of the operation of IC delay circuit. This IC delay circuit ensures that there is no

danger of blowing fuse or damaging parts even if operation is restarted accidentally.

5. This room air conditioner should not be used at the cooling operation when the outside temperature is

below –10°C (14°F).

6. This room air conditioner (the reverse cycle) should not be used when the outside temperature is below

–15°C (5°F).

If the reverse cycle is used under this condition, the outside heat exchanger will be frosted and its

efficiency falls.

7. When the outside heat exchanger is frosted, the frost is melted by operating the hot gas system, it is not

trouble that at this time fan stops and the vapour may rise from the outside heat exchanger.

CAUTION

–5 –

SPECIFICATIONS

MODEL

FAN MOTOR

FAN MOTOR CAPACITOR

FAN MOTOR PROTECTOR

COMPRESSOR

COMPRESSOR MOTOR CAPACITOR

OVERLOAD PROTECTOR

OVERHEAT PROTECTOR

FUSE (for MICROPROCESSOR)

POWER RELAY

POWER SWITCH

TEMPORARY SWITCH

SERVICE SWITCH

TRANSFORMER

VARISTOR

NOISE SUPPRESSOR

THERMOSTAT

REMOTE CONTROL SWITCH (LIQUID CRYSTAL)

138 W

YES

5.0A

G4A

YES

450NR

YES

YES(IC)

2700g

WITHOUT REFRIGERANT BECAUSE

COUPLING IS FLARE TYPE.

UNIT

PIPES

REFRIGERANT CHARGING

VOLUME

(Refrigerant 410A)

RAM-90QH5

JU1318D1

MAX. 75m

In case the pipe length is more than 30m, add refrigerant R410 at 15gram per every meter exceeds.

–6 –

SPECIFICATIONS FOR INDOOR UNITS COMBINATION

OPERATION SCOPE

TYPE

DC INVERTER FIVE SYSTEM MULTI COOLING AND HEATING

MODEL OUTDOOR UNIT

PHESE/VOLTAGE/FREQUENCY

CIRCUIT AMPERES TO CONNECT (A)

COOLING

(FIVE UNITS)

CAPACITY (kW)

(B.T.U./h)

TOTAL INPUT (W)

EER (B.T.U./hW)

TOTAL AMPERES (A)

POWER FACTOR (%)

HEATING

(FIVE UNITS)

CAPACITY (kW)

(B.T.U./h)

TOTAL INPUT (W)

EER (B.T.U./hW)

TOTAL AMPERES (A)

POWER FACTOR (%)

MAXIMUM LENGTH OF PIPING

STANDARD

RAM-90QH5

1ø, 220 - 240V, 50/60Hz

9.00 (3.20 - 9.90)

30,720 (10,920 - 33,780)

2,360 (600 - 3,040)

13.02

10.8 - 9.9

11.00 (3.40 - 12.10)

37,540 (11,610 - 41,290)

2,460 (610 - 2,910)

15.26

11.3 - 10.4

MAX. 75m (FIVE UNIT TOTAL)

CE (EMC&LVD)

RAM-90QH5

MODEL

PACKING

(mm)

cu.ft.

1,073

867

510

16.61

GROSS WEIGHT (kg)

6.35DX5/9.52DX3/12.70X2

FLARENUTSIZE (SMALL/LARGE)

INDOOR SUCTION

TEMPERATURE (˚C)

COOLING OPERATION SCOPE

OUTDOOR SUCTION

TEMPERATURE (˚C)

INDOOR SUCTION

HUMIDITY (%)

DEHUMIDIFYING

OPERATION

HEATING OPERATION

SCOPE

16 - 32 –10 ~ 43 BELOW 80

BELOW 27 –15 ~ 23

—

– 7 –

DC INVERTER SYSTEM MULTI R.A.C.

RAM-90QH5

COOL / HEAT CAPACITY SPEC. FOR INDOOR UNITS

COMBINATIONS TO BE ABLE TO OPERATE SIMULTANEOUSLY

Whichever indoor units are installed, cooling and heating capacity depends on how many and which indoor units

are operating at that time.

12.6

2740 3.28

3.32

3.28

3.54

3.32

3.24

3.27

3.25

2710

2740

2120

2560

2780

2750

2770

11.5

12.4 11.4

12.6 11.5

9.7 8.9

11.8 10.8

12.8 11.7

12.6 11.6

12.7 11.7

(Reference value)

5 ROOM MULTI-SPLIT INVERTER TYPE ROOM AIR CONDITIONER

POSSIBLE COMBINATION TO OPERATE (SAME TIME OPERATION)

–8 –

RATING CONDITON (DRY BLUB / WET BULB)

COOLING

HEATING

INDOOR OUTDOOR

27 / 19 ˚C

20 / –˚C

35 / 24˚C

7 / 6˚C

1.88 1.88 3.22 3.22

1.65 2.85 2.85 2.85

1.56 2.69 2.69 4.06

1.8+3.5+3.5+5.0

1.15+2.30+2.30+3.25

9.00 2530

2.18 2.74 2.74 2.74

* ONE UNIT INDICATED ARE ONLY FOR ONE UNIT OPERATION WHEN TWO OR MORE INDOOR UNITS ARE CONNECTED.

* TWO UNITS INDICATED ARE ONLY FOR TWO UNITS OPERATION WHEN TWO OR MORE INDOOR UNITS ARE CONNECTED.

* THREE UNITS INDICATED ARE ONLY FOR THREE UNITS OPERATION WHEN THREE OR MORE INDOOR UNITS ARE CONNECTED.

* FOUR UNITS INDICATED ARE ONLY FOR FOUR UNITS OPERATION WHEN FOUR OR FIVE INDOOR UNITS ARE CONNECTED.

–9 –

FIVE INVERTER SYSTEM MULTI R.A.C.

RAM-90QH5

INDOOR UNITS COMBINATIONS TO BE ABLE TO INSTALL

Two, three, four or five indoor units can be installed with one outdoor unit.

And total nominal cooling capacity should not be more than 15.5kW

Be sure to connect two or more indoor units to this outdoor unit. If not, condensed water may drop, resulting in

trouble.

INDOOR UNIT

MODEL

NOMINAL

COOLING

CAPACITY

(kW)

CAPACITY (kW)

at one unit operation

SUITABLE ROOM SIZE (m2)

at one unit operation

COOLING HEATING COOLING HEATING

RAK-18NH5

RAK-18NH6 1.8 1.00 - 2.50 1.10 - 3.20 8 - 12 9 - 11

RAK-25NH5

RAK-25NH6 2.5 1.00 - 2.80 1.10 - 4.70 11 - 17 14 - 18

RAF-25NH5 2.5 1.00 - 2.80 1.10 - 4.70 11 - 17 14 - 18

RAD-25NH5

RAD-25NH7 2.5 1.00 - 2.80 1.10 - 4.70 11 - 17 14 - 18

RAI-25NH5 2.5 1.00 - 2.80 1.10 - 4.70 11 - 17 14 - 18

RAK-35NH5

RAK-35NH6 3.5 1.00 - 3.90 1.10 - 5.80 16 - 24 17 - 22

RAF-35NH5 3.5 1.00 - 3.90 1.10 - 5.80 16 - 24 17 - 22

RAD-35NH5

RAD-35NH7 3.5 1.00 - 3.90 1.10 - 5.80 16 - 24 17 - 22

RAI-35NH5 3.5 1.00 - 3.90 1.10 - 5.80 16 - 24 17 - 22

RAK-50NH5

RAK-50NH6 5.0 1.00 - 5.60 1.10 - 7.20 23 - 34 23 - 29

RAF-50NH5 5.0 1.00 - 5.60 1.10 - 7.20 23 - 34 23 - 29

RAI-50NH5 5.0 1.00 - 5.60 1.10 - 7.20 23 - 34 23 - 29

RAD-50NH7 5.0 1.00 - 5.60 1.10 - 7.50 23 - 34 23 - 29

RAK-65NH5 6.0 1.00 - 6.50 1.10 - 9.00 27 - 41 25 - 32

Inhaltsverzeichnis

Andere Hitachi Klimaanlage Handbücher

Hitachi

Hitachi CJ Series Bedienungsanleitung

Hitachi

Hitachi RAM-36NP2A Bedienungsanleitung

Hitachi

Hitachi RPIL-1.0PNN1DH Bedienungsanleitung

Hitachi

Hitachi RAC-10EH1 Bedienungsanleitung

Hitachi

Hitachi RWM-(H)FSN3E Bedienungsanleitung

Hitachi

Hitachi RAS-DX10CFK Bedienungsanleitung

Hitachi

Hitachi RAS-S18CPA Bedienungsanleitung

Hitachi

Hitachi RAK-50PPA(T) Bedienungsanleitung

Hitachi

Hitachi SJ Series Bedienungsanleitung

Hitachi

Hitachi RAS-SX18HAK Bedienungsanleitung

Hitachi

Hitachi RAS-1.0PNNBDH1 Bedienungsanleitung

Hitachi

Hitachi RCI-1.0FSR Bedienungsanleitung

Hitachi

Hitachi RAM-68NP3B Bedienungsanleitung

Hitachi

Hitachi RAS-SD13CCT Bedienungsanleitung

Hitachi

Hitachi RAS-30CP1R Bedienungsanleitung

Hitachi

Hitachi RAS-60YHA4 Bedienungsanleitung

Hitachi

Hitachi RAS-10SH3 Bedienungsanleitung

Hitachi

Hitachi RAS-5HVRNM1E Bedienungsanleitung

Hitachi

Hitachi RAM-20MQ Bedienungsanleitung

Hitachi

Hitachi RAS-08KH2 Bedienungsanleitung

Hitachi

Hitachi RAK-18PEA Bedienungsanleitung

Hitachi

Hitachi RAC-E50YHA Bedienungsanleitung

Hitachi

Hitachi RAS-18KH(T1) Bedienungsanleitung

Hitachi

Hitachi RAS-X18CBT Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung