Hitachi E43 Bedienungsanleitung

TECHNICAL DATA

AND

SERVICE MANUAL

GENERATOR

E 43

E 60

E 71

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

LIST Nos. E 43: E027

E 60: E028

E 71: E029

August 2005

MODELS

E 43

E 60

E 71

Hitachi



Power Tools

E 60

CONTENTS

Page

1. PRODUCT NAME ........................................................................................................................... 1

2. MARKETING OBJECTIVE ............................................................................................................. 1

3. APPLICATIONS .............................................................................................................................. 1

4. SELLING POINTS .......................................................................................................................... 1

4-1. Selling Points Descriptions ............................................................................................................. 1

5. SPECIFICATIONS .......................................................................................................................... 2

6. CAPACITY OF GENERATOR ........................................................................................................2

6-1. Selection of Proper Generator ........................................................................................................ 2

6-2. Starting Current .............................................................................................................................. 3

7. PRECAUTIONS IN SALES PROMOTION ..................................................................................... 4

7-1. Handling Instructions ...................................................................................................................... 4

7-2. Thorough Instruction to the Customers .......................................................................................... 4

8. MAINTENANCE.............................................................................................................................. 5

9. TROUBLESHOOTING GUIDE ....................................................................................................... 6

9-1. Diagnosis and Corrective Action ..................................................................................................... 6

9-2. Checking Continuity ...................................................................................................................... 18

9-3. Tightening Torque ......................................................................................................................... 20

9-4. Wiring Diagram ............................................................................................................................. 22

Assembly Diagram for E 43

Assembly Diagram for E 60

Assembly Diagram for E 71

--- 1 ---

4300 VA

6000 VA

7100 VA

1. PRODUCT NAME

Hitachi Generator, Models E 43, E 60 and E 71

2. MARKETING OBJECTIVE

A series of generators, Models E 43, E 60 and E 71 will be put on the North American market in order to introduce

our new engine tools on overseas markets. The maximum output of these generators is shown in the following

table.

Model Max. output

E 43

E 60

E 71

All of these Models E 43, E 60 and E 71 comply with EPA (U.S. Environmental Protection Agency) and CARB (the

California Air Resources Board) emissions regulations. Please promote the sales of these Models E 43, E 60 and

E 71.

3. APPLICATIONS

Power source of electric appliances and tools

4. SELLING POINTS

4-1. Selling Points Descriptions

(1) Innovated design

Each of the Models E 43, E 60 and E 71 is of a powerful and innovated design.

(2) Equipped with Honda's tried-and-true OHV GX engine

Each of the Models E 43, E 60 and E 71 is equipped with Honda's tried-and-true OHV GX engine that is well

reputed in the North American market.

Model E 43: The maximum output of the engine is 5.9 kW (8 HP)/3600 min-1.

Model E 60: The maximum output of the engine is 8.1 kW (11 HP)/3600 min-1.

Model E 71: The maximum output of the engine is 9.6 kW (13 HP)/3600 min-1.

(3) Maintenance free, brushless alternator for increased durability

Innovated design

[Representative model: E 60]

Equipped with Honda's tried-

and-true OHV GX engine

E 43: 5.9 kW (8 HP)

E 60: 8.1 kW (11 HP)

E 71: 9.6 kW (13 HP)

Maintenance free, brushless

alternator for increased durability

--- 2 ---

5. SPECIFICATIONS

Rated AC voltage

Rated AC current

Rated AC output

Max. output

Phase

Frequency

Engine

Model

Max. output

Fuel tank capacity

Recommended fuel

Oil capacity

Recommended oil

Spark plug

General

Starting system

Oil alert system

Auto idle system

Dry weight

[Including accessory]

Dimensions

[Including accessory]

E43 E 60 E 71

in. (mm)

L x W x H

Generator

Model

lb (kg)

Amp

bhp (kW)/3600r/min.

Gallons (Liters)

Quarts (Liters)

31.7/15.9

3800

4300

120/240

41.7/20.8

5000

6000

Single

GX240 GX340 GX390

8 (5.9) 11 (8.1) 13 (9.6)

5 (18.9)

Unleaded gasoline(86 octane or higher)

1.16 (1.1)

SAE 10W-30 API SJ or SL

BPR6ES (NGK) or W20EPR-U (DENSO)

Recoil

Provided

42.3 x 29.4 x 29.0 (1075 x 746 x 737)

26.0 x 21.7 x 20.7 (660 x 550 x 525)

157 (71)

(198 (90))

181 (82)

(223 (101))

201 (91)

(243 (110))

50.0/25.0

6000

7100

6. CAPACITY OF GENERATOR

6-1. Selection of Proper Generator

Select the proper generator as follows according to the power consumption, output and the like of the AC

electrical equipment to be used.

(1) When the power consumption of the electrical equipment is known

When the power consumption of the electrical equipment is known, calculate the necessary output of the

generator (VA) according to the formula shown in the table below. When the sum of the calculated "necessary

output of the generator (VA)" is equal to or less than the rated AC output of the generator, the generator can

be used continuously.

1.0

Electrical equipment Power factor

Electric power tools

(Commutator motors)

Bulbs, electric heaters, etc.

General-purpose motors

(Induction motors)

0.8 to 0.95

0.4 to 0.75

Necessary output of the generator (VA)

Power consumption of the

electrical equipment (W)

Power factor

--- 3 ---

Power consumption of an electric circular saw, planer, disk grinder or the like may be higher depending on the

load. In order to deliver the full performance, it is necessary to estimate 1.5 to 2 times greater power

consumption.

(2) When the motor output of the electrical equipment is known

Some electrical equipment is not indicated with the current and the power consumption but the motor output.

In such cases, the generator can be used when the sum of the "necessary output of the generator (VA)"

obtained from the following formula is less than the rated AC output of the generator (VA).

Because a general electrical equipment is not indicated with the power factor, "0.8" is used in the case of an

electric power tool and "0.5" in the case of a general-purpose motor for the above rough calculation.

3800 VA

5000 VA

6000 VA

Generator Rated AC output

E 43

E 60

E 71

Generally, the following values are used though efficiency varies depending on the types of motors.

Motor output of the electrical equipment (W)

Efficiency x Power factor

Necessary output of the generator (VA) =

6-2. Starting Current

The current required from starting the above electrical equipment to operating in steady state is larger than the

current or the power required during "operation" of the electrical equipment. This is called "starting current".

There is no problem if no load is applied to an electric power tool equipped with a commutator motor from the

start. However, there may be a case that an electric power tool equipped with an induction motor (especially the

starting current of a split-phase induction motor is about three times larger than the current during operation)

cannot be started.

0.6

Electrical equipment Power factor

General-purpose motors

(Induction motors)

Electric power tools

(Commutator motors)

0.9

--- 4 ---

20 80

6040

20 100 F

20 30

2010

10 40 C

5W-30

10W-30

7. PRECAUTIONS IN SALES PROMOTION

In the interest of promoting the safest and most efficient use of the Models E 43, E 60 and E 71 Generators by all

of our customers, it is very important that at the time of sale the salesperson carefully ensures that the buyer

seriously recognizes the importance of the contents of the Handling Instructions, and fully understands the

meaning of the precautions listed on the Caution Plates attached to each unit.

7-1. Handling Instructions

Although every effort is made in each step of design, manufacture and inspection to provide protection against

safety hazards, the dangers inherent in the use of any generator cannot be completely eliminated. Accordingly,

specific precautions and suggestions for the use of the generator are listed in the Handling Instructions to

enhance the safe and efficient use of the tool by the customer. Salesperson must be thoroughly familiar with the

contents of the Handling Instructions to be able to offer appropriate guidance to the customer during sales

promotion.

7-2. Thorough Instruction to the Customers

(1) HITACHI electronic controlled products should not be used with portable generators.

Irregular generator power could cause these products to fail. Regarding other manufacturer's products, please

contact the manufacturer to see if it is safe to use the electronic controlled products with portable generators.

(3) Each generator has AC receptacles as shown in the table below.

(2) There is no oil in the engine crankcase when the generator is shipped. You must add oil before starting the

engine. Check the oil level before each use with the generator on a level surface and the engine stopped.

Engine oil is a major factor affecting engine performance and

service life. Non-detergent and 2-stroke oils will damage the engine

and are not recommended. Use 4-stroke motor oil that meets or

exceeds the requirements for API service classification SJ or SL.

Always check the API SERVICE label on the oil container to be sure

it includes the letters SJ or SL. SAE 10W-30 is recommended for

general, all-temperature use. Other viscosities shown in the right

graph may be used when the average temperature in your area is

within the indicated range.

Note that each of the above current values means the maximum current for one receptacle.

120 V

Output plug Voltage

GFCI (Ground-fault circuit interrupter)

Duplex receptacles

Twist-locking receptacles

120 V

120/240 V

20 A

Current

30 A

20 A

30 A

E 43

None

E 60

None

E 71

None

--- 5 ---

(4) When using an extension cord between the generator and an electrical equipment, it is necessary to observe

the specifications about the cord thickness (nominal cross sectional area of the core) and the length indicated

on the electrical equipment. If a long and thin extension cord is used, the voltage will be reduced remarkably

and the electrical equipment will be overheated or put out of action. To minimize voltage reduction, it is

necessary to use a short extension cord whose core is as thick as possible.

(5) Before operation, perform inspection according to the Handling Instructions.

8. MAINTENANCE

Periodical maintenance is required for efficient use of the Models E 43, E 60 and E 71 by the customers. Advise

the customers to thoroughly read and understand the maintenance instructions specified in the Handling

Instructions ("MAINTENANCE").

--- 6 ---

9. TROUBLESHOOTING GUIDE

9-1. Diagnosis and Corrective Action

Reinstall each part after the proper corrective action.

Stop the engine first then replace or check the parts.

Contact Honda Service Center for any trouble or repair of the engine.

Replenish with fuel.

Cause Corrective action Procedure

The engine does not start.

Trouble

There is no fuel.

Disassemble the strainer and

clean the components.

Clean the air cleaner element.

Deaerate fuel. 1 Open the fuel cock.

2 Remove the drain bolt from the carburetor and drain fuel into a

container for deaeration.

1 Remove the air cleaner cover.

2 Clean the element with oil or the like and dry it.

Soak the element in the engine oil and wring oil well from the element.

1 Remove the drain bolt.

2 Drain the engine oil.

3 Pour proper-viscosity engine oil.

1 Open the cup at the bottom of the strainer.

2 Clean the filter.

The engine starts but

stops soon.

The ignition plug is loose.

Air is mixed in fuel.

The strainer is clogged.

The electrodes of the ignition

plug are faulty.

The engine oil is highly viscous.

The air cleaner is clogged.

The carburetor is clogged.

Check and change the engine

oil.

The throttle valve is closed

due to improper adjustment of

the governor.

Tighten the ignition plug.

Clean the ignition plug. Adjust

the clearance between the

electrodes and replace the

ignition plug if abnormal.

Contact Honda Service Center.

1 Remove the plug cap.

2 Tighten the ignition plug with the exclusive plug wrench.

1 Remove the ignition plug.

2 Clean the electrodes with a wire brush or the like.

3 Check that the clearance between the electrodes is within the

range from 0.028 to 0.031 inch (from 0.7 to 0.8 mm).

Replace the ignition plug if there is any abnormality.

Contact Honda Service Center.

The oil level sensor is operated. A) Replenish with the engine oil

if short.

The oil level sensor is operated.

1 Remove the oil cap.

2 Add a proper amount of engine oil.

B) Check and replace the oil level

sensor. Contact Honda

Service Center.

A) Replenish with the engine oil

if short.

1 Remove the oil cap.

2 Add a proper amount of engine oil.

--- 7 ---

Cause Corrective action Procedure

The number of revolutions

does not increase.

Rated number of

revolutions of the engine

(no-load): 3,400 to

3,800 r/min (reference)

Trouble

Disassemble the strainer and

clean the components.

Clean the air cleaner element.

Deaerate fuel. 1 Open the fuel cock.

2 Remove the drain bolt from the carburetor and drain fuel into a

container for deaeration.

1 Remove the air cleaner cover.

2 Clean the element with oil or the like and dry it.

3 Soak the element in the engine oil and wring oil well from the

element.

1 Open the cup at the bottom of the strainer.

2 Clean the filter.

The carburetor is faulty.

Air is mixed in fuel.

The strainer is clogged.

Too much load is applied.

The governor is adjusted

improperly.

The air cleaner is clogged.

Contact Honda Service Center.

Check the connected electrical

equipment.

1 Remove the ignition plug.

2 Clean the electrodes with a wire brush or the like or replace the

ignition plug.

3 Check that the clearance between the electrodes is within the

range from 0.028 to 0.031 inch (from 0.7 to 0.8 mm).

Replace the ignition plug if there is any abnormality.

The ignition plug is stained or

the clearance is improper.

Contact Honda Service Center.

The number of revolutions

is abnormal.

(increase/decrease/large

variation)

Rated number of

revolutions of the engine

(no-load): 3,400 to

3,800 r/min (reference)

The carburetor is faulty.

Clean the iginition plug. Check

the clearance and replace the

ignition plug if abnormal.

The governor is adjusted

improperly.

Contact Honda Service Center.

Load varies greatly. Check the operating conditions

of the connected electrical

equipment.

Check the Breaker [124].

No voltage is generated

from the power receptacle.

The Breaker [124] is turned off.

The Thermal Protectors [117]

[119] are turned off.

Check the Thermal Protectors

[117] [119].

1 Disconnect the plug.

2 Turn on the Breaker [124].

1 Disconnect the plug.

Leave the Thermal Protectors [117] [119] for a while to cool them.

3 Press the button.

The engine starts but

stops soon.

The oil level sensor is operated. B) Check and replace the oil level

sensor. Contact Honda

Service Center.

--- 8 ---

Output voltage is generated

(about AC 115 to 125 V). No output voltage is generated.

Output voltage

Measure the resistance of the coil according to 9-2 (2).

The resistance is OK.

The Condenser

[145] is damaged

or deteriorated.

The main coil or

the sub coil is

broken or

short-circuited.

Cause (i)

[See page 9.]

Cause (iv)

[See page 10.]

Cause (vi)

[See page 11.]

Cause (v)

[See page 10.]

The field coil is

broken.

The rectifier built

in the Rotor Comp.

[3] is damaged.

The generator is faulty.

The resistance is extremely low.

The breaker is

faulty.

Cause (i)

[See page 9.]

The internal wiring

of the Panel Ass’y

[151] is short-

circuited or broken.

Cause (iii)

[See page 10.]

The Panel Ass’y [151] is faulty.

Cause Corrective action Procedure

No voltage is generated

from the power receptacle.

The voltage 240 V is not

outputted.

Trouble

If the trouble is caused by any cause other than the above, diagnose and take the necessary measures according to the following flow chart.



1 Remove the Tapping Screw D5 x 10 [6] and the End Cover [7].

2 Remove the two couplers of the Wire Harness [162] (white/blue and yellow/brown) that connects the Stator [12] with the Panel Ass’y [151].

Do not remove the coupler of the Wire Harness [162] (black/black).

3 Start the engine and check if output voltage is generated from the two couplers of the Wire Harness [162] (white/blue and yellow/brown) at

the Stator [12] side or not with a tester.

The Power Receptacle (GFCI)

[115] is operated.

Check the GFCI.

Turn the Select Switch [125] to

"240 V".

1 Disconnect the plug.

2 Press the reset button of the Power Receptacle (GFCI) [115].

3 Check if there is any abnormality (leakage) in the connected

electrical equipment. If there is abnormality, do not use the

electrical equipment.

1 Disconnect all the plugs from the Power Receptacles [115]

[118] [127].

2 Turn off the Breaker [124].

3 Turn the Select Switch [125] to "240 V".

Andere Handbücher für E43

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Wechselrichter Handbücher

Hitachi

Hitachi SJ300-EL Series Konfigurationshandbuch

Hitachi

Hitachi SJ-DN Bedienungsanleitung

Hitachi

Hitachi SJ700-2 Series Bedienungsanleitung

Hitachi

Hitachi X200 Series Bedienungsanleitung

Hitachi

Hitachi L2002 Bedienungsanleitung

Hitachi

Hitachi SJ100 Series Bedienungsanleitung

Hitachi

Hitachi J100-E2 SERIES Bedienungsanleitung

Hitachi

Hitachi E10U Fehlerbehebungshandbuch

Hitachi

Hitachi SJ-DG Bedienungsanleitung

Hitachi

Hitachi YUTAKI S COMBI Series Bedienungsanleitung

Hitachi

Hitachi L300P Series Bedienungsanleitung

Hitachi

Hitachi L100 Series Bedienungsanleitung

Hitachi

Hitachi HFC-VWS3 U SERIES, HFC-VWS3 H SERIES Bedienungsanleitung

Hitachi

Hitachi J300 Series Kurzanleitung

Hitachi

Hitachi L700 Series Bedienungsanleitung

Hitachi

Hitachi HFC-VWS3 U SERIES, HFC-VWS3 H SERIES Bedienungsanleitung

Hitachi

Hitachi J300U Series Gebrauchsanweisung

Hitachi

Hitachi SJ200 Series Bedienungsanleitung

Hitachi

Hitachi X200 Series Bedienungsanleitung

Hitachi

Hitachi SJ700-4000HFU2 Bedienungsanleitung

Hitachi

Hitachi WJ200 Series Software Bedienungsanleitung

Hitachi

Hitachi L100 Series Bedienungsanleitung

Hitachi

Hitachi L100 Series Bedienungsanleitung

Hitachi

Hitachi SH1 Series Benutzerhandbuch

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung