Hitachi SJ200 Series Bedienungsanleitung

• Single-phase Input 200V Class

• Three-phase Input 200V Class

• Three-phase Input 400V Class

Manual No. NB6501XA • March 2004

Hitachi Industrial Equipment Systems Co., Ltd.

SJ200 Series Inverter

Quick Reference Guide

Caution: Be sure to read the SJ200 Inverter Manual and follow

its Cautions and Warnings for the initial product installation.

This Quick Reference Guide is intended for reference use by

experienced users in servicing existing installations.

Power Circuit Terminals

Inverter models SJ200–002NFEF/NFU to –005NFEF/NFU

Jumper

+ –

U/T1 V/T2 W/T3

Chassis

Ground

Inverter models SJ200–007NFEF to –022NFEF, –007NFU to

–037LFU, –004HFEF/HFU to –040HFEF/HFU

Jumper

RB+ – U/T1 V/T2 W/T3

Chassis

Ground

Inverter models –055HFEF/HFU, 075HFEF/HFU

Jumper

+ –

L1 L2 N/L3

Chassis

Ground

L1 L2 N/L3

L1 L2 L3

NFEF, NFU

LFU, HFEF,

HFU

U/T1L1 L2 L3 V/T2 W/T3

U/T1 V/T2 W/T3

Control Circuit Terminals

Termina l

Name Description Ratings and Notes

PCS +24V for logic inputs 24VDC supply, 30 mA max.

(Notes: Do not use for network

power

Do not short to terminal L)

1, 2, 3, 4,

5, 6

Intelligent (program-

mable) discrete logic

inputs

27VDC max. (use P24 or an

external supply referenced to

terminal L), 4.7kΩinput

impedance

L (top

row)

GND for logic inputs Sum of input 1 to 6 currents

(Note: Do not ground)

11, 12 Discrete logic outputs 50 mA max. ON current,

27 VDC max. OFF voltage

CM2 GND for logic outputs 100 mA max for sum of

terminals 11 and 12 currents

AM Analog voltage output 0 to 10VDC, 1 mA max., 50%

duty cycle

L (bottom

row)

GND for analog signals Sum of OI, O, H, and AM

currents (return)

OI Analog input, current 4 to 19.6 mA range, 20 mA

nominal

H O OI

PCS

Analog

inputs

Analog

outputs

Alarm relay

Logic

outputs

Logic inputs

6 5 4 3 2 1

CM2

12 11

AL2 AL1 AL0

O Analog input, voltage 0 to 9.6 VDC range, 10VDC

nominal, 12VDC max., input

impedance 10 kΩ

H +10V analog reference 10VDC nominal, 10 mA max.

AL0 Relay common contact Contact rating

Max resistive load = 250VAC,

2.5A; 30VDC 3A;

Max inductive load = 250VAC,

0.2A; 30VDC 0.7A

Minimum load = 5VDC 100mA,

100VAC 10mA

AL1 Relay contact, normally

closed during RUN

AL2 Relay contact, normally

open during RUN

Terminal

Name Description Ratings and Notes

Basic Wiring Diagram

The following wiring diagram shows the power and motor connections

for basic operation. The optional signal input wiring supports external

Fwd and Rev Run command, and a speed potentiometer.

(L1)

(L2)

(N/L3)

(T2)

(T3)

(T1)

Motor

Forward

Reverse

Relay contacts,

1 Form C

Run signal

Frequency

arrival signal

Open collector

outputs:

External

speed

reference

pot.

SJ200

From 3-phase

power input

source (See

specifications

label on inverter

for details)

GND for logic

outputs

Load

GND for analog signals

Analog reference

PCS

CM2

AL0

AL1

AL2

Inputs:

GND for logic inputs

Inverter Keypad Operation

•Run/Stop LED – ON when the inverter output is ON and the motor is

developing torque, and OFF when the inverter output is OFF (Stop

Mode).

•Program/Monitor LED – ON when the inverter is ready for parame-

ter editing (Program Mode). It is OFF when the parameter display is

monitoring data (Monitor Mode).

•Run Key Enable LED – ON when the inverter is ready to respond to

the Run key, OFF when the Run key is disabled.

•Run Key – Press this key to run the motor (the Run Enable LED must

be ON first). Parameter F004, Keypad Run Key Routing, determines

whether the Run key generates a Run FWD or Run REV command.

•Stop/Reset Key – Press this key to stop the motor when it is running

(uses the programmed deceleration rate). This key will also reset an

alarm which has tripped.

•Potentiometer – Allows an operator to directly set the motor speed

when the potentiometer is enabled for output frequency control.

•Potentiometer Enable LED – ON when the potentiometer is enabled

for value entry.

(continued, next page...)

POWER

RUN

PRG

RUN STOP

RESET

HITACHI

FUNC

STR

50.0 Hz

HITACHI

ALARM

Parameter Display

Run/Stop LED

Program/Monitor LED

Run Key Enable LED

Run Key

Power LED

Display Units LEDs

Hertz

Amperes

Potentiometer

Enable LED

Potentiometer

Stop/Reset Key

Function Key

Up/Down Keys Store Key

Alarm LED

•Parameter Display – A 4-digit, 7-segment display for parameters and

function codes.

•Display Units: Hertz/Amperes – One of these LEDs will be ON to

indicate the units associated with the parameter display.

•Power LED – ON when the power input to the inverter is ON.

•Alarm LED – ON when the inverter in Trip Mode.

•Function Key – This key is used to navigate through the lists of

parameters and functions for setting and monitoring parameter values.

•Up/Down Keys – Use these keys alternately to move up or down the

lists of parameter and functions shown in the display, and to increment/

decrement values.

•Store Key – When the unit is in Program Mode and the operator has

edited a parameter value, press the Store key to write the new value to

the EEPROM.

Keypad Navigation Map

h007

h003

c1 48

c001

150

001

A1 46

A001

H––

C––

––

A–––

F004

F001

083

001

o.0

123.4

Edit

Increment/

decrement

value

Write data

EEPROM

Display data

Monitor Mode Program Mode

FUNC.

STR

FUNC.

Return to

parameter list

FUNC.

Select Parameter Edit Parameter

Store as

powerup

default

powerdown

Powerup Test

The Powerup Test procedure uses minimal parameter settings to run the

motor. The procedure describes two alternative methods for commanding

the inverter: via the inverter keypad, or via the logic terminals.

• Check power input and motor output wiring (see page 4 diagram).

• If using logic terminals for testing, verify correct wiring on [PCS],

[FW], [H], [O], and [L] (bottom row) per the diagram on page 4.

• Reverse [RV] input wiring (defaults to terminal [2]) is optional.

Step Description Via Keypad Via Logic

Ter minals

1 Set speed command

source setting

A001 = 00

(keypad pot.)

A001 = 01,

[H–O–L] input

2 Set Run FW command

source

A002 = 02

(Run key)

A002 = 01,

[FW] input

3 Set Run REV command

source

— C002 = 01,

[RV] input

4 Set motor base freq. A003 = 60

5 Set motor poles

(2 / 4 / 6 / 8)

H004 = 4 (default), change only if

your motor is different

6 Set keypad display to

monitor freq.

Access D001, press Func. key, display

will show 0.0

Perform safety check Disconnect load from motor

7 Turn keypad pot.

to MIN position

Ensure voltage on

[O]—[L] termi-

nals= 0V

8 Run Forward command Press Run key Turn ON the

[FW] terminal

9 Increase speed Rotate keypad

pot. CW dir.

Increase voltage

at [O]

10 Decrease speed Rotate keypad

pot. CCW dir.

Decrease voltage

at [O]

11 Stop motor Press Stop key Turn OFF the

[FW] terminal

12 Run Reverse command

(optional)

— Turn ON the [RV]

terminal

13 Stop motor — Turn OFF the

[RV] terminal

Andere Handbücher für SJ200 Series

Inhaltsverzeichnis

Andere Hitachi Wechselrichter Handbücher

Hitachi

Hitachi L100DN DeviceNet Series Addendum Merkblatt

Hitachi

Hitachi X200 Series Gebrauchsanweisung

Hitachi

Hitachi L100 IP Series Bedienungsanleitung

Hitachi

Hitachi NE-S1 series Bedienungsanleitung

Hitachi

Hitachi P1 Installationsanleitung

Hitachi

Hitachi WJ200-004M Bedienungsanleitung

Hitachi

Hitachi L2002 Bedienungsanleitung

Hitachi

Hitachi J300 Series Bedienungsanleitung

Hitachi

Hitachi X200-002SFE/NFU Handbuch

Hitachi

Hitachi L700 Series Bedienungsanleitung

Hitachi

Hitachi L200 Series Bedienungsanleitung

Hitachi

Hitachi L300P-110L Bedienungsanleitung

Hitachi

Hitachi L200 Series Kurzanleitung

Hitachi

Hitachi SJ Series Bedienungsanleitung

Hitachi

Hitachi WJ-0001S Bedienungsanleitung

Hitachi

Hitachi SJ2002 Series Bedienungsanleitung

Hitachi

Hitachi WJ200 Series Software Bedienungsanleitung

Hitachi

Hitachi SJ100 Series Bedienungsanleitung

Hitachi

Hitachi SJ300 Series Bedienungsanleitung

Hitachi

Hitachi L100 Series Bedienungsanleitung

Hitachi

Hitachi SJ100DN DeviceNet Series Addendum Montage- und Bedienungsanleitung

Hitachi

Hitachi air core 600 Bedienungsanleitung

Hitachi

Hitachi WJ200-001SF Bedienungsanleitung

Hitachi

Hitachi HFC-VWE2 SERIES Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung