Hitachi CM2073A Bedienungsanleitung
MODEL
CM2073A
(For
Europe)
1
OPERATING
GUIDE
GENERAL
The
CM2073A
is an ultra high resolution colour display designed for
CADKAMKAE
engineering and workstation use.
CM2073A’
s
key features
are=
*Ultra-high resolution
-
up to 1280 dots X 1024 lines
*Sharp focus by in-line high resolution CRT 20 inch
(19V)
with a
0.311~1
dot pitch matrix.
*Bright colour picture with low distortion due to the use of an
efficient high performance deflection yoke.
*Compact chassis and low power consumption with switching power
supply and self converging system.
*Ergonomically designed cabinet with tilt and swivel stand.
2
w
Bescheinigung des Herstellers
/
Importeurs
Hiermit wird bescheinigt,
da13
der
/
die
/
das Farbmonitor, Model1
CM2073A
(Gerat,
Typ, Bezeichnung) in
ubereinstimmung
mit den Bestimmungen der
Amtsbl.
163/1984
Vfg.
1046/1984
der Deutschen Bundespost
(Amtsblattverfugung)
funk -
entstdrt
ist.
Der Deutschen Bundespost wurde das Inverkehrbringen dieses
Gerites
angezeigt und die Berechtigung zur
uberprtifung
der Serie auf
Einhaltung der Bestimmungen
eingertiumt.
Hitachi Sales Europa
GmbH
WPOWER
SOURCE
This colour display is designed to operate on
220/240
volts 50 Hz,
AC. Insert the power cord plug into a
220/240
volts 50
Hz
safety
grounded outlet.
DO NOT CONNECT THE DISPLAY TO OTHER THAN THE SPECIFIED VOLTAGE.
Never remove the back cover of the display as this can expose you
to very high voltage and other hazards. If the display does not
operate properly, unplug the display and call your dealer.
NOTE :
1. This colour display is equipped vith a three-vire type
plug. This plug will only fit into a grounding-type
power outlet. This is a safety feature, do not defeat
the safety purpose of the grounding-type plug.
2. If the power cord or plug is damaged or frayed, replace
it.
3. Do not overload wall outlets or extension cords as this
can result in fire or electric shock.
TO PREVENT SHOCK OR FIRE HAZARD,
DO NOT EXPOSE THIS DISPLAY TO
RAIN OR MOISTURE..
3
CAUTIONS ON USE
CAUTIONS ON THE SUPPLY
VOL-
When the power voltage is
extremely high or low, it may
cause trouble or it may not give
optimum performance. Consult your
dealer at that time.
KEEP WATER OUT
When water of liquid enters the
set, it becomes dangerous to use
the unit. Immediately pull the
plug out and contact your dealer.
KEEP IN A WELL VENTILATED PLACE
Ventilation holes are provided in
the cabinet to prevent the
temperature from rising. Do not
place the unit in a place badly
ventilated or cover the unit with
materials such as clothes.
HIGH TEMPERATURE CAUSES TROUBLE
Avoid placing the unit in direct
sunshine, near a heating
appliance.
WHEN BEHAVIOUR IS ABNORMAL
When any abnormal sound, odour or
smoke is generated, push the
power switch off, pull the power
plug out from the socket and
contact your dealer.
CAUTIONS
TREATING THE SURFACE
Do not wipe the surface of the
set using volatile liquids such
as benzine or thinners, or any
chemically treated cloth; do not
apply insecticide. It may damage
the surface or cause peeling-off
of the paint. When a vinyl
product is kept in contact with
the surface for a long time,
stains may occur.
BE CAREFUL OF MAGNETISM
Do not bring materials which
generate magnetism, such as a
magnet, printers, floppy discs,
or transformers etc. nearby: the
set may be affected by magnetism,
causing
colour
disturbance or
picture distortion etc.
5
LOCATION OF CUSTOMER CONTROLS
[FRONT
vmwl
BRIGHTNESS CONTROL
CONTRAST CONTROL
/
/
DEGAUSSING SWITCH
POWER SWITCH
“0"
means power on.
“I" means power off.
\
POWER INDICATOR
(This illuminates
when power is on.)
Fig. 1
CONTRAST AND BRIGHTNESS CONTROLS
These may be adjusted by releasing the push in/out rotary controls.
DEGAUSSING SWITCH
This display is equipped with an automatic degaussing circuit (This
circuit operates when power is switched
on).
If the display is turned
horizontally and picture colour becomes un-uniform, push this switch
to get fine colour uniformity. Picture may become still after some ten
seconds.
6
[REAR
VIEW]
R.G.B. SIGNAL INPUT
FUSE
F901
I
SYNC SIGNAL INPUT
I
(Some displays
are not equipped
with this sync.
input and 75 OHM
terminator.)
AC CORD INLET
1
175 OHM TERMINATORS
Fig. 2
FUSE
F901
Please always use
4A/25DV
IEC type fuse, (contact service personnel).
SIGNAL CABLE CONNECTION
Connect R.G.B. signal BNC connectors to the signal input. When one
display is used, the 75 OHM terminator must be connected to
yout"
BNC
connector (see Fig.4
).
When two more displays are used at the same
time (loop through state) see Fig.6 for connecting cables.
7
[SIGNAL
CABLE CONNECTION)
from signal
generator
75 OHM terminator
(must be connected)
Fig. 3 75 OHM terminator connection
(side view)
from signal generator
I
from signal generator
Fig. 4 cable connection
(rear view)
,,,,/
/$TK~-'-j
to next display
Fig. 6 2 more displays case
(loop through state) signal cable
v
Fig. 5 terminator not connected
a
VIDEO INPUT SIGNAL TIMING
CHART-
1. SEPARATE SYNC
L
**********in case of
CM2073AME-S-315
t
R.G.B. signal (analogue)
1
*
(HORIZONTAL) (VERTICAL)
_
.---
(R.G.B.)I
r;/;ELHy-
u
I
i.S
’
p-20.47-
4
(unit:
pS)
p813H-d
(unit: H)
Fig. 7 Fig. 8
2. SYNC. ON
GREEN**********in
case of
CM2073A-312/315
CM2073AME-S-315
Green Signal
/-f11.5c120.47pJ
(unit:
pS)
I
I
J-
(unit: H)
Fig. 9
9
INSTALLATION INSTRUCTIONS
FOR DEALERS
ADJUSTMENTSFORTHE
CM2073A
ONINSTALLATION
.
This document lists the
ad.iustmcnt
fcat,rlrrs of thr
20738
available to
the dealer. Other
ad.justment.s
exist
which
are
not readily accessible
,'
and should not be attempted by untrained personnel.
1
The
CM2073A
comes in various configurations including displays for
line rates of nominal
50kHz
and
60kHz
operations, line synchronisation
on the green video
drive9
separate line synchronisation, with or
without D.D.C. (Dig:ital Dynamic Convergence) and models with internal
timing to preferred video driving boards.
Before any of the adjustments below are attempted, please ensure that
the model has been chosen appropriately from the options listed on
page 16 of the operating guide.
The adjustments listed in this note permit some deviations from this
table, but it is important that the most appropriate model be chosen.
ADJUSTMENTS
Before attempting any of the following adjustments, the display should
be powered up for a period of 15 minutes prior to the
ad-justment.
I
1. Switch on the
power9
noting that. the green power indicator adjacent
.:.
to the power switch comes on, If it does not;
a>
Check power source and connections
b)
Check fuse
c)
Call a service engineer
10
Inhaltsverzeichnis
Andere Hitachi Monitor Handbücher
Hitachi
Hitachi UT42MX70U Bedienungsanleitung
Hitachi
Hitachi LCD Monitor Bedienungsanleitung
Hitachi
Hitachi CM1721ME Bedienungsanleitung
Hitachi
Hitachi StarBoard T-17SXL Bedienungsanleitung
Hitachi
Hitachi CMP307XE Bedienungsanleitung
Hitachi
Hitachi 32LD7800TA Bedienungsanleitung
Hitachi
Hitachi CML153XW Bedienungsanleitung
Hitachi
Hitachi CM813ET Bedienungsanleitung
Hitachi
Hitachi CML171SXW Bedienungsanleitung
Hitachi
Hitachi CM1797M Bedienungsanleitung
Hitachi
Hitachi CMP420V1 Bedienungsanleitung
Hitachi
Hitachi DS55MU01 Bedienungsanleitung
Hitachi
Hitachi CM2111M Bedienungsanleitung
Hitachi
Hitachi 42HDM12A Bedienungsanleitung
Hitachi
Hitachi 55HDM71 - 55" Plasma Panel Bedienungsanleitung
Hitachi
Hitachi CML152XW - 15" LCD Monitor Bedienungsanleitung
Hitachi
Hitachi 32HDT50 Bedienungsanleitung
Hitachi
Hitachi CML152XW2 Bedienungsanleitung
Hitachi
Hitachi CML154XW Bedienungsanleitung
Hitachi
Hitachi CML200UXWB Bedienungsanleitung
