Hitachi 43FDX20B Bedienungsanleitung

PROJECTION COLOR TV

53FDX20B 43FDX20B

53SDX20B 43FDX15B

53SDX20BB

OPERATING GUIDE

IMPORTANT SAFETY INSTRUCTIONS 2-3

FIRST TIME USE 4-18

REMOTE CONTROL

ULTRATEC BIT-MAP

ON-SCREEN DISPLAY

USEFUL INFORMATION INDEX 61-66

30-60

19-29

CUSTOMIZE

SETUP VIDEO AUDIO

THEATER

SEL

As an ENERGY STAR®Partner, Hitachi, Ltd. has determined that this

product meets the ENERGY STAR®guidelines for energy efficiency.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this

section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain

from it to the proper operation of your HITACHI television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the

improbable event that a safety problem should be discovered in your product model.

Follow all warnings and instructions marked on this color television.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of a

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO RAIN

OR MOISTURE.

NOTE: • There are no user serviceable parts inside the color television.

•Model and serial numbers are indicated on back side of the television.

• This television is not intended for use in a computer room.

POWER SOURCE

THIS TELEVISION IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE

POWER CORD INTO A 120 VOLT 60Hz OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE COLOR TELEVISION’S (POLARIZED) PLUG WITH AN

EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE COLOR TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER THAN

THE SPECIFIED VOLTAGE.

CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other

hazards. If the television does not operate properly, unplug the television and call your authorized dealer or

service center.

NOTE: This television receiver will display television closed captioning, ( or ), in accordance with

paragraph 15.119 of the FCC rules.

CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not

expressly approved by HITACHI could void the user’s authority to operate the television.

MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that

are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s

authority to operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Follow all warnings and instructions marked on this television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the

cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

15. Televisions are designed to comply with the

recommended safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or top,

of the cabinet which could cause the product to

overturn resulting in product damage and/or personal

injury.

16. Follow instructions for wall, shelf or ceiling mounting as

recommended by the manufacturer.

17. An outdoor antenna should not be located in the

vicinity of overhead power lines or other electrical

circuits.

18. If an outside antenna is connected to the receiver be

sure the antenna system is grounded so as to provide

some protection against voltage surges and built up

static charges. Section 810 of the National Electric

Code, ANSI/NFPA No. 70-1984, provides information

with respect to proper grounding for the mast and

supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding

connectors, location of antenna-discharge unit,

connection to grounding electrodes and requirements

for the grounding electrode.

Note to the CATV system installer: This reminder is

provided to call the CATV system installer’s attention to

Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding

system of the building, as close to the point of cable

entry as practical.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

Do not place any objects on the top of the

television which may fall or cause a child to climb

to retrieve the objects.

Disposal of this product may require specific

instructions pertaining to your resident state. For

disposal or recycling information, please contact

your local authorities or the Electronic Industries

Alliance: www.eiae.org.

PREVENTION OF PATTERN BURN

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-

moving) patterns can cause permanent damage to television receivers. Such “PATTERN BURNS” constitute misuse and are NOT

COVERED by your HITACHI Factory Warranty. When using the Picture-in-Picture function, the sub-picture should not be left

permanently in one corner of the screen or a “PATTERN BURN” may develop over a long period of time.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require

prior authorization from the broadcaster or owner of the video program material.

ACCESSORIES

1. Remote Control Unit CLU-4322UG (Part No. HL01832).

2. Two “AA” size, 1.5V batteries (For Remote Control Unit).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the

cover off.

2. Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs

and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Lift up on tab to

remove back cover.

Check to make sure you have the following accessories before disposing of the packing material.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

CAUTION: Television stand model SP-43H is designed for use with a 43 inch or smaller television set. Use of a smaller

stand, a non Hitachi recommended stand or a generic stand may result in instability, causing possible injury.

123

456

789

ANT STATUS

VOL CH

POWER

TV CBL/SAT DVD/VCR

PIP SWAP PIP MODE FREEZE

HELP PIP CH MENU

MUTE EXIT LAST CH

REC ASPECT MODE

SELECT

PART NAME PART NO. ILLUSTRATION

CLU-4322UG

REMOTE CONTROL HL01832

1. 2.

43” TELEVISION

STAND

SP-43H

(Not included,

order separately)

OPTIONAL

H530047

CUSTOM HITACHI TELEVISION STAND

Excellent for VCR and video-tape storage.

Special features include smoked glass doors

and an adjustable shelf. Available in shark grey.

CLU-4322UG

VID1 VID2 VID3 VID4

VID5

HOW TO SET UP YOUR NEW HITACHI PROJECTION TV

CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too close

to the television. Move the magnetic field source away from the television until there is no picture distortion.

4' MINIMUM

5' 10' 15'

BEST

HORIZONTAL

VIEWING ANGLE

20'

ANTENNA

Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended

for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image

ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location

selected allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can

become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various

locations in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as

the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the

reflection or the TV can be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing

the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For

best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or

behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker

placement for best performance.

0' 5' 10' 15'

BEST

VERTICAL VIEWING

ANGLE

20'

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.

For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output

and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna

adapter (300-Ohm to 75-Ohm).

Phono Connector

Used on all standard video and audio cables which connect to

inputs and outputs located on the television’s rear jack panel and

front control panel.

''F'' Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the antenna

jack on the television.

S-VIDEO (Super Video) Connector

This connector is used on camcorders, VCRs, and laserdisc

players with an S-VIDEO feature in place of the standard video

cable to produce a high quality picture.

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect the outdoor

antenna or CATV coaxial cable to the ANT A (75-Ohm) terminal. If

you have a second antenna or cable TV system, connect the coaxial

cable to the ANT B terminal.

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect

the VHF or UHF antenna leads to screws of the VHF or UHF

adapter. Plug the adapter into the antenna terminal on the TV.

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna

terminal, and connect the cables to the antenna mixer. Consult

your dealer or service store for the antenna mixer.

To outdoor antenna

or CATV cable

To second antenna

or cable system

Antenna mixer

ANT A/ANT B

To UHF

Antenna

To outdoor

antenna or

CATV system

To outdoor VHF

or UHF antenna

FRONT PANEL CONTROLS

NOTES: 1. Your HITACHI Projection TV will appear to be turned OFF if there is no video input when VIDEO: 1, 2, 3, 4 or 5 is

selected. Check the Power Light to make sure the TV is turned off when not in use.

2. To see an auto-demonstration of the on-screen displays with HELP text displayed, press and hold the POWER

button on the TV set for approximately five seconds. Press the POWER button on the TV again to end the auto-

demonstration.

FRONT VIEW

MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This

button also serves as the SELECT button when in MENU mode.

INPUT/EXIT button

Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source. Your selection is shown in

the top right corner of the screen. This button also serves as the EXIT button when in MENU mode.

CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as

the cursor down () and up () buttons when in MENU mode.

VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve

as the cursor left () and right () buttons when in MENU mode.

POWER button

Press this button to turn the TV on or off.

)

(

쏐

MAGIC

FOCUS

POWER INPUT

EXIT SELECT

  

  

Push open door and

pull forward and down

PUSH

POWER INPUT



EXIT

VOL+VOL-

CH-

CH+

VOL+VOL-

CH-

CH+

SELECT

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on your choice (see page 21).

FRONT PANEL CONTROLS

POWER light

You will see a red light when the TV is turned on.

PERFECT PICTURE sensor

The Perfect Picture sensor will make automatic picture adjustments depending on the amount of light in the room to give the best

picture. (see page 57)

REMOTE CONTROL sensor

Point your remote at this area when selecting channels, adjusting volume, etc.

MAGIC FOCUS

Use this button to adjust your picture quality to optimum performance. (see page 39)

FRONT INPUT JACKS (for VIDEO: 3)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording.

Press the INPUT button until VIDEO: 3 appears in the top right corner of the TV screen. If you have mono sound, insert the audio

cable into the left audio jack.

FRONT PANEL JACKS AND CONNECTIONS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

MAGIC

FOCUS

OUTPUT

V L R

S-VHS

Back of VCR

S- NPUT

(Optional, see note)

NPUT 3

AUD O

S-V DEO

V DEO L/MONO R

INPUT

OUTPUT

REAR PANEL JACKS

Antenna Input/Output

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can

be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a

sub-picture.) The antenna output labeled “TO CONVERTER” allows the ANT A connection to pass directly to a different source

such as a cable box, only when ANT B is displayed as a main picture.

Audio/Video Inputs 1, 2, 4 and 5

The VID1~VID5 buttons will select each video source each time it is pressed. Use the audio and video inputs to connect external

devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the

left audio jack.)

MONITOR OUT

These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video

output.

AUDIO TO HI-FI Output

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be

controlled by the television’s main volume.

S-VIDEO Inputs 1 and 2

Inputs 1 and 2 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.









AUDIO TO HI-FI



ANT A

CONVERTER

ANT B

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 1 and 2, but only one of these inputs may be used at a

time.

NOTE: S-VIDEO Output may be used for recording, only when the input is of S-VIDEO type.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektionsfernsehen Handbücher

Hitachi

Hitachi 53SDX01B Bedienungsanleitung

Hitachi

Hitachi 51XWX20B Bedienungsanleitung

Hitachi

Hitachi 43FDX10B Bedienungsanleitung

Hitachi

Hitachi 50EX39B Bedienungsanleitung

Hitachi

Hitachi 55FX20B Bedienungsanleitung

Hitachi

Hitachi 50GX49B Bedienungsanleitung

Hitachi

Hitachi 53UWX10BA Bedienungsanleitung

Hitachi

Hitachi 46F500 Bedienungsanleitung

Hitachi

Hitachi C43-FL9000 Bedienungsanleitung

Hitachi

Hitachi 62VS69 - UltraVision VS69 Series Bedienungsanleitung

Hitachi

Hitachi 46UX24B Bedienungsanleitung

Hitachi

Hitachi 50UX58B Bedienungsanleitung

Hitachi

Hitachi 57UWX20B Bedienungsanleitung

Hitachi

Hitachi 50VF820 - 50" Rear Projection TV Bedienungsanleitung

Hitachi

Hitachi 50VS69A Bedienungsanleitung

Hitachi

Hitachi 50EX12BA Bedienungsanleitung

Hitachi

Hitachi 42V515 - 42" Rear Projection TV Bedienungsanleitung

Hitachi

Hitachi 57S715 Bedienungsanleitung

Hitachi

Hitachi 50C20 - LCD Projection TV Bedienungsanleitung

Hitachi

Hitachi 50V500 - UltraVision Digital - 50" Rear Projection... Bedienungsanleitung

Hitachi

Hitachi 50EX11BV/12KV Bedienungsanleitung

Hitachi

Hitachi 53SDX89B Bedienungsanleitung

Hitachi

Hitachi 51F710G Bedienungsanleitung

Hitachi

Hitachi 50V720 - 50" Rear Projection TV Bedienungsanleitung

Beliebte Projektionsfernsehen Handbücher anderer Marken

Samsung

Samsung ST-43T6P Bedienungsanleitung

Toshiba

Toshiba ColorStream TP50G60 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric WD-65734 Bedienungsanleitung

Optoma

Optoma EP652A Bedienungsanleitung

Samsung

Samsung SP43T8HPX/XEC Bedienungsanleitung

Philips

Philips 28PW6006 - annexe 1 Bedienungsanleitung

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Benutzerhandbuch

Philips

Philips 43PP8421 Bedienungsanleitung

RCA

RCA P52950 Bedienungsanleitung

Sony

Sony KP-51DS1U Bedienungsanleitung

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Bedienungsanleitung

Pioneer

Pioneer Elite PRO 510HD Bedienungsanleitung

Philips

Philips 43PP8421 Handbuch

JVC

JVC I'Art Pro AV-48P776 Bedienungsanleitung

Sony

Sony GRAND WEGA KDF-55XS955 Bedienungsanleitung

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Bedienungsanleitung

Toshiba

Toshiba 42HM66 - 42" Rear Projection TV Bedienungsanleitung

Philips

Philips 50PL9200D Bedienungsanleitung