Hitachi CP-SX1350 Series Bedienungsanleitung

Projector

CP-SX1350

User's Manual - Operating Guide

TECHNICAL

INTER

INPUT

M1-D

RGB

BNG

S-VIDEO

STANDBY/ON

TEMP

VIDEO

COMPONENT

LAMP

KEYSTONE

RESET

FOCUS

LENSSHIFTZOOM

Dimensions

210

420

85.5 (at the bottom of lens position) to 92.99 (at the top of lens position)

160

150 320

[unit: mm]

•Be sure to check jack type, signal level, timing and resolution before

connecting this projector to a computer.

•Some computers may hove multiple display screen modes. Use of some of these

modes will not be possible with this projector.

•Depending on the input signal, full-size display may not be possible in some cases.

Refer to the number of display pixels above.

•Although the projector can display signals with resolution up to UXGA (1600 x 1200),

the signal will be converted to the projector’s panel resolution before being

displayed. The best display performance will be achieved if the resolutions of the

input signal and projector panel are identical.

•Automatically adjustment may not function correctly with some input signals.

•The image may not be displayed correctly when the input sync. signal is a composite

sync. or a sync. on G.

NOTE

Example Of Computer Signal

Resolution

H ××VfH (kHz) fV (Hz) Rating Signal mode Display mode

720 ×400 37.9 85.0 VESA TEXT Zoom in

640 ×480 31.5 59.9 VESA VGA (60Hz) Zoom in

630 ×480 35.0 66.7 Mac13"mode Zoom in

640 ×480 37.9 72.8 VESA VGA (72Hz) Zoom in

640 ×480 37.5 75.0 VESA VGA (75Hz) Zoom in

640 ×480 43.3 85.0 VESA VGA (85Hz) Zoom in

800 ×600 35.2 56.3 VESA SVGA (56Hz) Zoom in

800 ×600 37.9 60.3 VESA SVGA (60Hz) Zoom in

800 ×600 48.1 72.2 VESA SVGA (72Hz) Zoom in

800 ×600 46.9 75.0 VESA SVGA (75Hz) Zoom in

800 ×600 53.7 85.1 VESA SVGA (85Hz) Zoom in

832 ×624 49.7 74.5 Mac16"mode Zoom in

1024 ×768 48.4 60.0 VESA XGA (60Hz) Zoom in

1024 ×768 56.5 70.1 VESA XGA (70Hz) Zoom in

1024 ×768 60.0 75.0 VESA XGA (75Hz) Zoom in

1024 ×768 68.7 85.0 VESA XGA (85Hz) Zoom in

1152 ×864 67.5 75.0 VESA SXGA (75Hz)

1280 ×960 60.0 60.0 VESA SXGA (60Hz)

1280 ×1025 64.0 60.0 VESA SXGA (60Hz)

1280 ×1024 80.0 75.0 VESA SXGA (75Hz)

1400 ×1050 65.2 60.0 VESA SXGA+(60Hz)

1600 ×1200 75.0 60.0 VESA UXGA (60Hz) Zoom out

Initial Set Signals

The following signals are used for the initial settings. The signal timing of some computer

models may be different. In such case, adjust the items V POSITION and H POSITION in

the PICTURE-2 menu.

DATA

H. Sync.

V. Sync.

DATA

Display interval c

Back porch b

Sync. a

Front porch d

Display interval c

Back porch b

Sync. a

Front porch d

Computer /

Signal

Horizontal signal timing (µs)

a b c d

TEXT 2.0 3.0 20.3 1.0

VGA (60Hz) 3.8 1.9 25.4 0.6

Mac 13"mode 2.1 3.2 21.2 2.1

VGA (72Hz) 1.3 3.8 20.3 1.0

VGA (75Hz) 2.0 3.8 20.3 0.5

VGA (75Hz) 1.6 2.2 17.8 1.6

SVGA (56Hz) 2.0 3.6 22.2 0.7

SVGA (60Hz) 3.2 2.2 20.0 1.0

SVGA (72Hz) 2.4 1.3 16.0 1.1

SVGA (75Hz) 1.6 3.2 16.2 0.3

SVGA (85Hz) 1.1 2.7 14.2 0.6

Mac 16"mode 1.1 3.9 14.5 0.6

XGA (60Hz) 2.1 2.5 15.8 0.4

XGA (70Hz) 1.8 1.9 13.7 0.3

XGA (75Hz) 1.2 2.2 13.0 0.2

XGA (85Hz) 1.0 2.2 10.8 0.5

1152×864 (75Hz)

1.2 2.4 10.7 0.6

1280×960 (60Hz)

1.0 2.9 11.9 0.9

1280×1024 (60Hz)

1.0 2.3 11.9 0.4

1280×1024 (75Hz)

1.1 1.8 9.5 0.2

1400×1050 (60Hz)

1.2 2.0 11.4 0.7

1600×1200 (60Hz)

1.2 1.9 9.9 0.4

Computer /

Signal

Vertical signal timimg (lines)

a b c d

TEXT 342 400 1

VGA (60Hz) 233 480 10

Mac 13"mode 339 480 3

VGA (72Hz) 328 480 9

VGA (75Hz) 316 480 1

VGA (75Hz) 325 480 1

SVGA (56Hz) 222 600 1

SVGA (60Hz) 423 600 1

SVGA (72Hz) 623 600 37

SVGA (75Hz) 321 600 1

SVGA (85Hz) 327 600 1

Mac 16"mode 339 624 1

XGA (60Hz) 629 768 3

XGA (70Hz) 629 768 3

XGA (75Hz) 328 768 1

XGA (85Hz) 336 768 1

1152×864 (75Hz)

332 864 1

1280×960 (60Hz)

336 960 1

1280×1024 (60Hz)

338 1024 1

1280×1024 (75Hz)

337 1024 2

1400×1050 (60Hz)

332 1050 2

1600×1200 (60Hz)

346 1200 1

• Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω

terminator (positive)

• H./V. sync. Signal: TTL level (positive/negative)

• Composite sync. Signal: TTL level

D-Sub 15 pin shrink jack

Connection T

Connection To The Ports

o The Ports

Pin Signal Pin Signal Pin Signal

1Video input Red 6Ground Red --

2Video input Green 7Ground Green =SDA (DDC)

3Video input Blue 8Ground Blue qH./Composite sync.

4-9-wV. sync.

5Ground 0Ground eSCL (DDC)

ARGB

54321

67890

ewq=-

• Type: T.M.D.S.

•

Amplitude differential: DC 150-1200 mV / AC 1.56 Vp-p

• Amplitude: TTL level (positive/negative)

M1-D jack

Pin Signal Pin Signal Pin Signal

1T.M.D.S. Data2 + -T.M.D.S. Data1 + oT.M.D.S. Data0 +

2T.M.D.S. Data2 - =T.M/D.S. Data1 - pT.M.D.S. Data0 -

3T.M.D.S. Data2 Return qT.M.D.S. Data1 Return [T.M.D.S. Data0 Return

4T.M.D.S. Clock Return wT.M.D.S. Clock + ]USB +5V DC Input

5-eT.M.D.S. Clock - \DDC & USB Return

6V. Sync. rUSB Date + aDDC Date (SDA)

7-tUSB Date - sDDC Clock (SCL)

8Hot Plug Detect

(+5V DC Output) y-dDDC +5V DC Input

9-u-f-

0-i-g-

BM1-D

CBNC (R,G,B,H,V)

• BNC jack x5

• Video: Analog 0.7 Vp-p, 75 Ωterminator

• H/V. sync. : TTL level (positive/negative)

• Composite sync. : TTL level

DAUDIO IN 1, EAUDIO IN 2, HAUDIO IN R, L, MAUDIO OUT

• 3.5 dia. Stereo mini jack

• 200 mVrms, 57k Ωterminator

]\asdfg [po

iuytrewq=-

8709 654321

VIDEOR-AUDIO IN-L S-VIDEO

BNC

RGB

AUDI O IN1

AUDI O IN2 RGB OUT AUDI O OUT

R/CR/PRG/Y B/CB/PBHV

CONTROL NETWORK

CR/PR Ca/Pa

REMOTE CONTROL

Connection T

Connection To The Ports (continued)

o The Ports (continued)

• Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω

terminator (positive)

• H./V. sync. Signal: TTL level (positive/negative)

• Composite sync. Signal: TTL level

D-Sub 15 pin shrink jack

Pin Signal Pin Signal Pin Signal

1Video output Red 6Ground Red --

2Video output Green 7Ground Green =-

3Video output Blue 8Ground Blue qH./Composite sync.

4-9-wV. sync.

5Ground 0Ground e-

LRGB OUT

54321

67890

ewq=-

Mini Din 4 pin jack

IVIDEO IN

• RCA jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60

• 1.0 ± 0.1 Vp-p at 75 Ωterminator

KCOMPONENT (CR/PR, CB/PB, Y)

• RCA jack x3

• System: 525i (480i), 525p (480p), 625i (576i), 720p, 1080i/1035i

• Y signal: 1.0 ± 0.1 Vp-p at 75 Ωterminated with composite sync.

• CB/PBsignal: 0.7 ± 0.1 Vp-p at 75 Ωterminated

• CR/PRsignal: 0.7 ± 0.1 Vp-p at 75 Ωterminated

VIDEOR-AUDIO IN-L S-VIDEO

BNC

RGB

AUDI O IN1

AUDI O IN2 RGB OUT AUDI O OUT

R/CR/PRG/Y B/CB/PBHV

CONTROL NETWORK

CR/PR Ca/Pa

REMOTE CONTROL

L N

NREMOTE CONTROL

• 3.5 dia. Stereo mini jack

• To be connected with the remote control that came with the projector.

ODC OUT

JS-VIDEO Pin Signal

1Color signal: 0.286 Vp-p (NTSC, burst), 75 Ωterminator

Color signal: 0.300 Vp-p (PAL/SECAM, burst), 75 Ωterminator

2Brightness signal: 1.0 Vp-p, 75 Ωterminator

3Ground

4Ground

Connection T

Connection To The Ports (continued)

o The Ports (continued)

VIDEOR-AUDIO IN-L S-VIDEO

BNC

RGB

AUDI O IN1

AUDI O IN2 RGB OUT AUDI O OUT

R/CR/PRG/Y B/CB/PBHV

CONTROL NETWORK

CR/PR Ca/Pa

REMOTE CONTROL

D-Sub 9 pin

plug

CONTROL port

FCONTROL

GNETWORK

• RJ-45 (10BASE-T) jack

12345

6 7 8 9

Computer side

D-Sub 9 pin

jack

54321

9 8 7 6

GND

CTS

RTS

DTR

GND

DSR

RTS

DTS



D-Sub 9 pin

jack

54321

9 8 7 6

D-Sub 9 pin

plug

RS-232C port

12345

6 7 8 9



memo About the details of RS-232C communication, please refer to the

following page.

RS-232C Communication

Connecting The Cable

Turn off the projector and the computer power supplies.

Connect the CONTROL port of the projector with a RS-232C port of the computer by

a RS-232C cable. Use the cable that fulfills the specification shown in the previous

page.

Turn on the computer power supply and after the computer has started up, turn on

the projector power supply.

19200bps, 8N1

1. Protocol

Consist of header (7 bytes) + command data (6 bytes).

2. Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low : Lower byte of CRC flag for command data

CRC_high : Upper byte of CRC flag for command data

3. Command data

Command Data Chart

Communications Setting

byte_0 byte_1 byte_2 byte_3 byte_4 byte_5

Action Type Setting code

low high low high low high

Action (byte_0 - 1)

Action Classification Content

1SET Change setting to desired value.

2GET Read projector internal setup value.

4INCREMENT Increment setup value by 1.

5DECREMENT Decrement setup value by 1.

6EXECUTE Run a command.

RS-232C Communication (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2

bytes)+‘00H’+‘00H’) from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +

setting code (2 bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+

type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the specified setting to the default value.

(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+

type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+

type (2 bytes) +‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

When the projector cannot understand the received command

When the projector cannot understand the received command, the error code ‘15H’ is

sent back to the computer.

Sometimes the projector cannot properly receive the command. In such a case, the

command is not executed and the error code ‘15H’ is sent back to the computer. If this

error code is returned, send the same command again.

When the projector cannot execute the received command.

When the projector cannot execute the received command, the error code ‘1cH’ +

‘xxxxH’ is sent back to the computer. When the data length is greater than indicated by

the data length code, the projector ignore the excess data code.

Conversely when the data length is shorter than indicated by the data length code, an

error code will be returned to the computer.

•Operation cannot be guaranteed when the projector receives an

undefined command or data.

•Provide an interval of at least 40ms between the response code and any other code.

•The projector outputs test data when the power supply is switched ON, and when the

lamp is lit. Ignore this data.

•Commands are not accepted during warm-up.

NOTE

RS-232C Communication (continued)

Command Data Chart

Names Operation type Header Command data

CRC Action Type Setting code

Keystone V

Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00

Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00

Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00

Keystone V Reset

Execute

BE EF 03 06 00 08 D0 06 00 0C 70 00 00

Keystone H

Get BE EF 03 06 00 E9 D0 02 00 0B 20 00 00

Increment BE EF 03 06 00 8F D0 04 00 0B 20 00 00

Decrement BE EF 03 06 00 5E D1 05 00 0B 20 00 00

Keystone H Reset

Execute

BE EF 03 06 00 98 D8 06 00 20 70 00 00

Brightness

Get BE EF 03 06 00 89 D2 02 00 03 20 00 00

Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00

Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00

Brightness Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00

Contrast

Get BE EF 03 06 00 FD D3 02 00 04 20 00 00

Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00

Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00

Contrast Reset Execute

BE EF 03 06 00 A4 D2 06 00 01 70 00 00

Aspect Set

4:3

BE EF 03 06 00 9E D0 01 00 08 20 00 00

16:9

BE EF 03 06 00 0E D1 01 00 08 20 01 00

SMALL

BE EF 03 06 00 FE D1 01 00 08 20 02 00

NORMAL

BE EF 03 06 00 5E DD 01 00 08 20 10 00

REAL

BE EF 03 06 00 5E D7 01 00 08 20 08 00

Get

BE EF 03 06 00 AD D0 02 00 08 20 00 00

Whisper Set NORMAL

BE EF 03 06 00 3B 23 01 00 00 33 00 00

WHISPER

BE EF 03 06 00 AB 22 01 00 00 33 01 00

Get

BE EF 03 06 00 08 23 02 00 00 33 00 00

Mirror Set

Normal

BE EF 03 06 00 C7 D2 01 00 01 30 00 00

H Inverse

BE EF 03 06 00 57 D3 01 00 01 30 01 00

V lnverse

BE EF 03 06 00 A7 D3 01 00 01 30 02 00

H&V Inverse

BE EF 03 06 00 37 D2 01 00 01 30 03 00

Get

BE EF 03 06 00 F4 D2 02 00 01 30 00 00

(This table is continued to the following page.)

RS-232C Communication (continued)

Command Data Chart (continued)

Names Operation type Header Command data

CRC Action Type Setting code

Language Set

ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00

FRANÇAIS

BE EF 03 06 00 67 D2 01 00 05 30 01 00

DEUTSCH BE EF 03 06 00 97 D2 01 00 05 30 02 00

ESPAÑOL BE EF 03 06 00 07 D3 01 00 05 30 03 00

ITALIANO BE EF 03 06 00 37 D1 01 00 05 30 04 00

NORSK BE EF 03 06 00 A7 D0 01 00 05 30 05 00

NEDERLANDS

BE EF 03 06 00 57 D0 01 00 05 30 06 00

PORTUGUÊS

BE EF 03 06 00 C7 D1 01 00 05 30 07 00

日本語

BE EF 03 06 00 37 D4 01 00 05 30 08 00

BE EF 03 06 00 A7 D5 01 00 05 30 09 00

BE EF 03 06 00 37 DE 01 00 05 30 10 00

BE EF 03 06 00 57 D5 01 00 05 30 0A 00

SVENSKA BE EF 03 06 00 C7 D4 01 00 05 30 0B 00

BE EF 03 06 00 F7 D6 01 00 05 30 0C 00

SUOMI BE EF 03 06 00 67 D7 01 00 05 30 0D 00

POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00

TÜRKÇE BE EF 03 06 00 07 D6 01 00 05 30 0F 00

Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00

Gamma Set

NORMAL BE EF 03 06 00 C7 F0 01 00 A1 30 00 00

CINEMA BE EF 03 06 00 57 F1 01 00 A1 30 01 00

DYNAMIC BE EF 03 06 00 A7 F1 01 00 A1 30 02 00

CUSTOM BE EF 03 06 00 07 FD 01 00 A1 30 10 00

Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00

Custom Gamma

Get BE EF 03 06 00 08 F1 02 00 A0 30 00 00

Increment BE EF 03 06 00 6E F1 04 00 A0 30 00 00

Decrement BE EF 03 06 00 BF F0 05 00 A0 30 00 00

Custom

Color Temp

Set

USER BE EF 03 06 00 3B F8 01 00 B0 30 10 00

HIGH BE EF 03 06 00 0B F5 01 00 B0 30 03 00

MIDDLE BE EF 03 06 00 9B F4 01 00 B0 30 02 00

LOW BE EF 03 06 00 6B F4 01 00 B0 30 01 00

Get BE EF 03 06 00 C8 F5 02 00 B0 30 00 00

Custom User R Set

50 BE EF 03 06 00 57 F7 01 00 B1 30 05 00

60 BE EF 03 06 00 C7 F6 01 00 B1 30 04 00

70 BE EF 03 06 00 F7 F4 01 00 B1 30 03 00

80 BE EF 03 06 00 67 F5 01 00 B1 30 02 00

90 BE EF 03 06 00 97 F5 01 00 B1 30 01 00

100 BE EF 03 06 00 07 F4 01 00 B1 30 00 00

Get BE EF 03 06 00 34 F4 02 00 B1 30 00 00

Custom User G Set

50 BE EF 03 06 00 13 F7 01 00 B2 30 05 00

60 BE EF 03 06 00 83 F6 01 00 B2 30 04 00

70 BE EF 03 06 00 B3 F4 01 00 B2 30 03 00

80 BE EF 03 06 00 23 F5 01 00 B2 30 02 00

90 BE EF 03 06 00 D3 F5 01 00 B2 30 01 00

100 BE EF 03 06 00 43 F4 01 00 B2 30 00 00

Get BE EF 03 06 00 70 F4 02 00 B2 30 00 00

(This table is continued to the following page.)

Andere Handbücher für CP-SX1350 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi CP-DW10N Bedienungsanleitung

Hitachi

Hitachi CP-X2530WN Installationsanleitung

Hitachi

Hitachi CP-TW2503 Bedienungsanleitung

Hitachi

Hitachi ED-27X Bedienungsanleitung

Hitachi

Hitachi ED-A100 - XGA LCD Projector Montage- und Wartungsanleitung

Hitachi

Hitachi LP-EU5002 Bedienungsanleitung

Hitachi

Hitachi CP-X430 series Bedienungsanleitung

Hitachi

Hitachi CP-X809 Bedienungsanleitung

Hitachi

Hitachi CP-X380W Bedienungsanleitung

Hitachi

Hitachi CP-SX5600W Bedienungsanleitung

Hitachi

Hitachi ED-A101EF A1B-20 Bedienungsanleitung

Hitachi

Hitachi CP-SX5500 Bedienungsanleitung

Hitachi

Hitachi Innovate CP-RX94 Bedienungsanleitung

Hitachi

Hitachi CP-D31N guide Bedienungsanleitung

Hitachi

Hitachi CP-AW312WN guide Bedienungsanleitung

Hitachi

Hitachi CP-X3030WN Bedienungsanleitung

Hitachi

Hitachi CP-EX3051WN Bedienungsanleitung

Hitachi

Hitachi CP-X2011N Bedienungsanleitung

Hitachi

Hitachi CP-X2541WN Bedienungsanleitung

Hitachi

Hitachi CP-X205 Technisches Dokument

Hitachi

Hitachi CP-X990W Bedienungsanleitung

Hitachi

Hitachi CP-X935W Bedienungsanleitung

Hitachi

Hitachi CP-A100 Series Technisches Dokument

Hitachi

Hitachi CP-X8150 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung